Optimization of the surface texture for silicon carbide sliding in water

Surface texturing has been recognized as an effective means to improve the tribological performances of sliding surfaces. Usually, generation additional hydrodynamic pressure to increase the load carrying capacity is regarded as the most significant effect of surface texture. In the case of silicon carbide sliding against identical material in water, the experimental results indicate that surface texture is also helpful to improve the running-in progress to smooth the contact surfaces, showing another reason to result in low friction. Based on the consideration of enhancing the generation of hydrodynamic pressure and improving running-in progress, a surface texture pattern, which was combined with large (circle, 350 μm in diameter) and small (rectangular, 40 μm in length) dimples, was designed to maximize the texture effect on the load carrying capacity of SiC surfaces sliding in water. The friction coefficient of such textured surface was evaluated and compared with that of untextured and those only with large or small dimples only. The friction reduction mechanisms of the patterns with different dimples in size are discussed.     

Estimation of growth rate in unidirectionally solidified multicrystalline silicon by the growth-induced striation method

Multicrystalline silicon was grown by unidirectional solidification method using the accelerated crucible rotation technique. The application of the accelerated crucible rotation technique in unidirectional solidification method induced growth striations across the axial direction of the grown crystal. This striation pattern was observed from carbon concentration distribution, obtained by using Fourier transform infrared spectroscopy. The generated striation pattern was found to be weak and discontinuous. Some striations were absent, probably due to back melting, caused during each crucible rotation. From the growth striations and applied time period in crucible rotation, the growth rate was estimated by using Fourier transformation analysis.     

Design and synthesis of labeling reagents (MS probes) for highly sensitive electrospray ionization mass spectrometry and their application to the detection of carbonyl, alcohol, carboxylic acid and primary amine samples.

Novel labeling reagents, called MS probes, which possess a positively charged quaternary amine moiety and can transform a neutral analyte into a charged compound by simply mixing with the analyte and allowing the mixture to stand from several minutes to 30 min at room temperature or while heating to 50 degrees C, were designed and synthesized for the highly sensitive detection of carbonyl, alcohol, carboxylic acid and primary amine samples by electrospray ionization mass spectrometry (ESI-MS). The positively charged products can be detected with high sensitivity in an ESI-MS system, which is the most popular liquid MS instrument. All of the labeled products showed a remarkably large increase in the molecular-ion peak abundance detection sensitivity of over 500-fold at picomolar concentration levels compared to that of unlabeled analytes in an ESI-MS system. These MS probes, used together with liquid MS detection, are widely applicable as a convenient method for the highly sensitive detection of less than picomolar levels of analytes, and therefore greatly enhance the power of ESI-MS analysis.     

Ion-exchange selectivity of anion exchange resin modified with polystyrenesulfonic acid.

In order to change the ion-exchange selectivity of anion-exchange resin, the surface of a gel-type anion exchange resin was modified with anionic polyelectrolyte, polystyrenesulfonic acid. Using this modified resin, the ion-exchange rate of nitrate was little decreased, but that of sulfate was evidently decreased. It is considered that the ion-exchange reaction of the multivalent anion is suppressed by the greater electrostatic repulsive force against the modification layer than that against the monovalent anion. Thus, this modified resin may be suitable for the selective separation of monovalent anions. The influence of the modified condition on the ion-exchange rate was examined. Furthermore, this modified resin was used to separate nitrate ions from sulfate ions in the aqueous solution.     

Ruijsenaars' Commuting Difference Operators as Commuting Transfer Matrices

For Belavin's elliptic quantum R-matrix, we construct an L-operator as a set of difference operators acting on functions on the type A weight space. According to the fundamental relation RLL=LLR, taking the trace of the L-operator gives a set of commuting difference operators. We show that for the above mentioned L-operator this approach gives Macdonald type operators with elliptic theta function coefficient, actually equivalent to Ruijsenaars' operators. The relationship between the difference L-operator and Krichever's Lax matrix is given, and an explicit formula for elliptic commuting differential operators is derived. We also study the invariant subspace for the system which is spanned by symmetric theta functions on the weight space. Received: 27 December 1995 / Accepted: 11 November 1996     

High-quality hydroxyapatite coating on biocompatible materials by laser-assisted laser ablation method

A new method for high-quality hydroxyapatite (HAp) coating is developed, the laser-assisted laser ablation method. In this method, two lasers are used. One is used for ablation of a HAp target. The other, the assist laser, is used to irradiate a Ti substrate surface. The effects of the assist laser irradiation are to anneal the HAp coating and to improve its adhesive strength to the Ti substrate. The quality of the HAp coating depends on the delay time of the assist-laser irradiation. HAp coatings obtained at a delay time of 10 microseconds or more are more amorphous. It was confirmed that the amorphous part of a coating dissolves in simulated body fluid, while the crystalline part does not. The value of the Ca/P ratio in a coating obtained at a delay time of a few microseconds is close to the stoichiometric value. PACS 81.16.Mk     

Keratinized epithelial transport of beta-blocking agents. I. Relationship between physicochemical properties of drugs and the flux across rat skin and hamster cheek pouch.

The maximum fluxes (Jmax) of beta-blockers through keratinized membranes were determined in vitro and compared with their physiochemical parameters such as lipophilicity (log k'0) and melting point (mp). Rat abdominal skin and hamster cheek pouch mucosa were used as the model membranes. Propranolol, metoprolol, timolol, pindolol, nadolol and agenolol were used as beta-blockers with a variety of physicochemical characters. Linear relations of Jmax with either log k'0 or mp were observed both in intact rat skin and in intact hamster cheek pouch, suggesting that the lipophilicity and thermodynamic activity of a drug in the crystal state primarily affect the drug's permeation through these membranes. However, the slope, dJmax/d(log k'0), for cheek pouch mucosa was greater than that for rat skin, corresponding to the lack of appendigeal shunt pathways in cheek pouch. Penetration studies using the delipidized membranes and the isolated stratum corneum sheet of hamster cheek pouch mucosa clarified that the primary rate-limiting barrier function might exist in the lipid layer of the stratum corneum. Jmax values for the tape-stripped and delipidized skins correlated with both the solubilities of drugs in the vehicle and with the mp, suggesting the polar porous characteristics of both model membranes. However, a theoretical approach confirmed that the contribution of an intracellular or aqueous pore route in the intact membrane to the permeation of drugs with positive lipophilic indexes is negligible.     

Simple and rapid determination of trace amounts of gold(III), palladium(II), and platinum(IV) in industrial waste solutions after recovery of noble metals by combined use of GFAAS and anion-exchange separation.

A simple and rapid method for the analysis of trace amounts of gold(III), palladium(II), and platinum(IV) by the combined use of graphite furnace atomic absorption spectrometry and anion-exchange separation was proposed, and successfully applied to the rapid determination of metals in industrial waste solutions obtained from the final process of noble-metal recovery factories, because noble metals can be selectively and quantitatively separated to a high degree by using a small column containing only a 0.7 g-portion of a common anion-exchange resin and a dilute thiourea solution.     

Spectrophotometric determination of copper(II) with carbon disulfide,a secondary amine and triton X-100

Copper(II) is determined by non-extractive spectrophotometry as a complex of butylene dithiocarbamate formed in situ by reaction between carbon disulfide and pyrrolidine in aqueous Triton X-100 medium. This method is similar to that with butylene dithiocarbamate as starting material in the sense of simplicity, sensitivity, precision and accuracy. Pyrrolidine is the best of seven secondary amines tested in this way for copper determinations.