Simulation of collisions of two droplets containing two different liquids using incompressible smoothed particle hydrodynamics method

Theoretical and Computational Fluid Dynamics - The present study aims to simulate a collision of two droplets containing immiscible liquids by employing a three- dimensional incompressible smoothed...     

The required sample size in measuring oblique incidence absorption coefficient Experimental study

It is an important issue to clarify the minimum required size of a specimen for the accurate measurement of oblique incidence absorption coefficient. Investigation is made on the basis of experimental studies in a laboratory, using Aoshima's time stretched pulse technique. Measurements are carried out for glass fiber with thickness of 50 and 100 mm as highly absorbing materials and for ceramic with a thickness of 52 mm as relatively low absorbing material. The tested surface areas range from 0.0625 to 42 m² for glass fiber and from 0.1563 to 39.168 m² for ceramics. The absorption coefficients are determined at incidence angles from 0 to 45° in increments of 15°. With consideration of an active surface bounded by ellipse orbit, the minimum required surface area is 16 m² with a ratio of length to width of about 1.25. This value is twice the area size of the active surface, which is calculated from the geometry of source and microphone, and the width of the temporal window.     

Studies on glycolipids. III. Glyceroglycolipids from an axenically cultured cyanobacterium, Phormidium tenue.

Seven new monogalactosyl diacylglycerols (1-7) and six new digalactosyl diacylglycerols (11-16) were isolated from an axenically cultured cyanobacterium, P. tenue. Their structures were elucidated on the basis of physicochemical evidence and the results of enzymatic hydrolysis using a lipase (from Rhizopus arrhizus). Comparison of antialgal activity for P. tenue between monogalactosyl diacylglycerols (1-8) and digalactosyl diacylglycerols (11-19) revealed that the former showed more potent activity than the latter.     

Structural developments in synthetic rubbers during uniaxial deformation by in situ synchrotron X‐ray diffraction

The molecular orientation and strain‐induced crystallization of synthetic rubbers—polyisoprene rubber, polybutadiene rubber, and butyl rubber [poly(isobutylene isoprene)]—during uniaxial deformation were studied with in situ synchrotron wide‐angle X‐ray diffraction. The high intensity of the synchrotron X‐rays and the new data analysis method made it possible to estimate the mass fractions of the strain‐induced crystals and amorphous chain segments in both the oriented and unoriented states. Contrary to the conventional concept, the majority of the molecules (50–75%) remained in an unoriented amorphous state at high strains. Each synthetic rubber showed a different behavior of strain‐induced crystallization and molecular orientation during extension and retraction. Our results confirmed the occurence of strain‐induced networks in the synthetic rubbers due to the inhomogeneity of the crosslink distribution. The strain‐induced networks containing microfibrillar crystals and oriented amorphous tie chains were responsible for the ultimate mechanical properties. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 956–964, 2004     

Ion-pair formation of a copper(II)-ammine complex with an anionic surfactant and the recovery of copper(II) from ammonia medium by the surfactant-gel extraction method.

The extraction and separation of copper(II), zinc(II), cobalt(II), and cadmium(II) were investigated. Both copper(II) and zinc(II) formed ammine-complexes, while cadmium(II) and cobalt(II) formed hydroxide precipitates in an ammonia medium. By the addition of sodium dodecylsulfate (SDS), a copper(II) complex formed an ion-pair (copper-ammine-DS), which was extracted into the SDS phase. However, a zinc(II) complex did not form an ion-pair, and was soluble in water. Copper(II) ion was recovered by stripping (back-extraction) after the addition of hydrochloric acid. This method was applied to the separation of copper(II) in a brass alloy.     

Optical and electric properties of Nb-doped anatase TiO2 single crystal

Nb-doped anatase TiO₂ single crystal has been grown by chemical vapour transport method. Raman spectra shows that the obtained crystal with Nb of 0.08 wt% has typical anatase structure. An absorption band was observed at around 2.2 eV, which seems to be due to the d-d transition in the conduction band. The electron paramagnetic resonance and electric resistivity measurements show that the doped niobium makes quite shallow donor level whose orbital is d_xy-like centered at the titanium position of anatase.