Improvement in flow-sheet of extraction chromatography for trivalent minor actinides recovery

Journal of Radioanalytical and Nuclear Chemistry - Extraction chromatography flow-sheet employing octyl(phenyl)-N,N-diisobutylcarbonoylmethylphosphine oxide and bis(2-ethylhexyl) hydrogen phosphate...     

The required sample size in measuring oblique incidence absorption coefficient Experimental study

It is an important issue to clarify the minimum required size of a specimen for the accurate measurement of oblique incidence absorption coefficient. Investigation is made on the basis of experimental studies in a laboratory, using Aoshima's time stretched pulse technique. Measurements are carried out for glass fiber with thickness of 50 and 100 mm as highly absorbing materials and for ceramic with a thickness of 52 mm as relatively low absorbing material. The tested surface areas range from 0.0625 to 42 m² for glass fiber and from 0.1563 to 39.168 m² for ceramics. The absorption coefficients are determined at incidence angles from 0 to 45° in increments of 15°. With consideration of an active surface bounded by ellipse orbit, the minimum required surface area is 16 m² with a ratio of length to width of about 1.25. This value is twice the area size of the active surface, which is calculated from the geometry of source and microphone, and the width of the temporal window.     

Non-destructive rapid analysis of brominated flame retardants in electrical and electronic equipment using Raman spectroscopy.

Using Raman spectroscopy without any preparation, we analyzed the brominated flame retardant, polybromodiphenyl ethers (PBDEs), which has been prohibited by the European Union. The typical Raman bands of PBDEs, which are clearly different from those of other brominated flame retardants, are from 100 to 300 cm(-1). In our analysis, the detection limit was about 100 ppm, and the analysis took about 1 min, whereas the usual method of solvent extraction using gas chromatography/mass spectroscopy takes 50 h.     

A system for measuring absolute frequencies of up to 4.25 THz using a Josephson point contact

A system for measuring the absolute frequency of a far-infrared (FIR) laser is described. Josephson point contacts have been utilized in the system as a frequency harmonic mixer connecting microwaves and optically pumped CH₃OH laser lines. The Josephson point contacts are capable of generating beat signals of 90 GHz microwaves and FIR waves of up to 4.25 THz. To measure the frequency of the beat signals from the Josephson junction with a frequency counter, tracking oscillators have been developed, which tracks the beat signals by phase locking and regenerate clean signals for frequency counting. It is shown that the absolute frequency can be measured to an accuracy of about 100 Hz by using the tracking oscillators.     

A new route for the construction of the AB-ring core of Taxol

A new method for the construction of the AB-ring core of Taxol was developed utilizing a new skeletal transformation protocol as a pivotal step. The acid-catalyzed rearrangement of the cyclopentenone-allene photoadduct gave a bridged seven-membered ketone, which was easily transformed, using the intramolecular Suzuki reaction and the oxidative cleavage of the vicinal diol, to the bicyclic diketone.     

Development of Non-Halogen Flame Retardant Optical Fiber and Optical Fiber Cord

A non-halogen highly flame-retardant 0.9mm optical fiber and 2.0mm simplex optical cord, which are harmonized with the ecosystem, have been developed. The characteristics of them are presented in this paper.     

Optical current transducers using flint glass fiber as the faraday sensor element

This paper describes development of the optical current transducers using flint glass fiber as the Faraday effect sensing element. Excellent polarization properties of the fiber with low birefringence are described, and the design and test data of a current transducer using the fiber manufactured for use in electric power facilities are reviewed. Experimental results on flexible characteristics of a scheme with round trip light transmission in the fiber is also reported.     

Effect of structural variation within cationic azo-surfactant upon photoresponsive function in aqueous solution

The cationic azo-surfactants possessing different spacers and tail alkyl chain lengths have been synthesized by azocoupling ofp-alkylaniline orop-ethoxyaniline with phenol, followed by alkylation and quaternalization with dibromoalkane and trimethylamine, respectively. These surfactants showed a good solubility in water. A reversibletrans-cis isomerization of the azosurfactants by photoirradiation was assessed by UV-Vis absorption spectra. Due to a difference in HLB between thetrans- andcis-surfactants, the observed critical micelle concentration (CMC) values and the electric conductivity of the surfactant solution at above the CMC were significantly affected by the photoinducedtrans-cis isomerization. The azo-surfactants bearing moderate alkyl chain lengths such as surfactants 6 (R₂=C₂H₄, R₃=C₄H₉) and 9 (R₂=C₄H₈, R₃=C₂H₅) were found to be effective to achieve large CMC changes (3.6 mmol/L for 6 and 5.9 mmol/L for 9) by UV-light irradiation. The replacement of the tail chain species also affected the photoresponsive function. The surfactant 12, possessingp-ethoxy group as the tail chain, was found to form a stable micelle aggregation as compared with the structurally related surfactant 10 having ethyl unit as its tail group, but it exhibited a large CMC change (5.3 mmol/L) by UV-light irradiation.     

Anomalous PL brightening caused by partial Auger recombination of a (D, X) complex during an impact ionization avalanche in n-GaAs

Partial Auger recombination of the (D⁰, X) bound-exciton in n-GaAs at 4.2 K during an impact ionization avalanche under an applied pulse voltage has been investigated. The bright photoluminescence (PL)-pattern observed by applying the pulse voltage, characterizes well the formation of a current density filament. The observation of the bright PL spectra inside the current density filament gives a quite new result concerning the partial Auger recombination process of the (D⁰, X) complex, leaving the neutral donor in the excited states.     

Ethylene polymerization by chromium complexes with phosphorous‐bridged bisphenoxy ligand

Chromium catalysts combined with phosphorous‐bridged bisphenoxy ligands were found to be highly active for ethylene polymerization. The most efficient catalyst precursor among them, generated by combining bis[3‐tert‐butyl‐5‐methyl‐2‐hydroxyphenyl](phenyl)phosphine hydrochloride ( 1a ) and CrCl₃(THF)₃, was characterized. X‐ray analysis of (3‐tert‐butyl‐5‐methyl‐2‐phenoxy)(3‐tert‐butyl‐5‐methyl‐ 2‐hydroxyphenyl)(phenyl)phosphine bis(tetrahydrofuran)chromium dichloride ( 6 ), obtained by the reaction of 1a and CrCl₃(THF)₃ in the presence of NaH, revealed a unique structure in which one phenol moiety of the bisphenol did not coordinate to the chromium center. Complex 6 showed higher activities than those observed in the in situ catalyst system. Polyethylene of various molecular weights was obtained with differing activators. The highest activity (113.5 kg mmol (cat)^?1 h^?1) was observed when TIBA/TB was used as a cocatalyst. A medium molecular weight polymer with narrow molecular weight distribution (M_w = 128,700, M_w/M_n = 1.8) was obtained using a 6 ‐TIBA/B(C₆F₅)₃ system. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3668–3676, 2007