Magnetic hysteresis of the magnetoresistance and the critical current density in polycrystalline YBa2Cu3O7−δ–Ag superconductors

A systematic study of the magnetic hysteresis in transport properties of polycrystalline YBa₂Cu₃O_7−δ–Ag compounds has been made based on two kinds of measurements at 77 K and under applied magnetic fields up to 30 mT: critical current density J_c(B_a) and magnetoresistance R(B_a). The R(B_a) curves show a minimum in their decreasing branch occurring at B=B_min which was found to be both the excitation current I_ex and the maximum applied magnetic field B_am dependent. In addition, for a certain value of B_am>5 mT, we have observed that B_min increases with increasing I_ex and reaches a saturation value. The J_c(B_a) curves show a maximum in decreasing applied magnetic fields occurring at B=B_max. We have also found that B_max increases with increasing B_am and reaches a saturation value. The minimum in the R(B_a) and the maximum in J_c(B_a) curves were found to be related to the trapped flux within the grains. All the experimental results are discussed within the context of the flux dynamics and transport mechanisms in these high-T_c materials.     

Immobilized polysiloxanes as stationary phases for high-performance liquid chromatography and solid phase extraction

Polysiloxanes immobilized onto the surfaces of porous silica particles have proven to be good stationary phases for the separation of multiresidues of pesticides and their metabolic/degradation products by reversed-phase high-performance liquid chromatography (RP-HPLC). Similar materials have proven effective for pre-concentration and clean-up procedures using solid phase extraction. The present paper describes the preparation and some applications of several of these packing materials.     

Spherical Particles of Zirconia-Titania of Hexagonal Structure from a Neutral Amine Route

Through the sol–gel process, using the so-called neutral amine route, spherical particles of 1:1 zirconia–titania were synthesized from zirconium(IV) and titanium(IV) butoxides as well as 1,12-diaminododecane as precursor species. The obtained product exhibited a hexagonal structure, as determinated by X-ray diffraction data. The obtained material was also characterized by thermogravimetry, differential scanning calorimetry, infrared spectroscopy, scanning electron microscopy, and surface area measurements. Despite the release of template molecules on heating, the spherical morphology was retained up to about 1200°C, at which the disruption of the spheres took place.     

The spatial distribution of poly(methyloctylsiloxane) deposited by solvent evaporation in the pores of HPLC silica particles

Summary Poly(methyloctylsiloxane) (PMOS), sorbed into the pores of HPLC silica particles by solvent evaporation, can function as a useful stationary phase for reversed-phase chromatography. The present work addresses the question of how the PMOS is distributed in the pores. Measurements of the surface area (BET, N₂) of a series of partially loaded samples (0–40% PMOS, m/m) using a typical batch of HPLC silica (10 μm irregular particles with 6 nm pores) show that the specific surface area of the samples decreases linearly with the specific loading (mass of PMOS per gram of silica). This result is not consistent with a “film” model in which the PMOS is deposited uniformly on the pore walls, but is consistent with a model in which long segmented “plugs” of PMOS are deposited within the pore system. Presented at the 21^st ISC held in Stuttgart, Germany, 15^th–20^th September, 1996     

A simple spectrophotometric procedure for the determination of antimony (III) and (V) in antileishmanial drugs

A spectrophotometric method for the selective determination of antimony (III) and (V) in antileishmanial drugs is described. The procedure is based on the reaction of Sb(III) with bromopyrogallol red (BPR) in neutral solution. As a consequence of the Sb-BPR complex formed, the absorbance of BPR, at 560 nm, decreases proportionally to the amount of Sb(III) in the analyte solution. The calculated apparent molar absorptivity and determination limits are 3.67 × 10⁴ L · cm^–1 · mol^–1 and 1.65 × 10^–6 mol/L, respectively. Sb(V) is determined after reduction to Sb(III) by iodide. The Sb(V) content determined in ten samples of Glucantime varied from 75.40 ± 0.97 to 94.47 ± 1.0 mg/mL. Sb(III) was detected in all samples analyzed, and mean values ranged from 5.19 ± 0.16 to 10.52 ± 0.15 mg/mL. The method is suitable for the routine quality control of pharmaceutical formulations. Received: 26 July 1996 / Revised: 17 October 1996 / Accepted: 11 December 1996     

Chromatographic and column stability at pH 7 of a C18 dimethylurea polar stationary phase

Chromatographic evaluations of a C18 dimethylurea phase in 150 mm x 3.9 mm HPLC columns were performed using the Tanaka and Engelhardt test mixtures. The applicability of the new C18 dimethylurea phase was also evaluated with a mixture of some herbicides and their metabolites. An artificial aging procedure was also performed by passing a potassium phosphate mobile phase buffered at pH 7.0 through C18 50 mm x 3.9 mm dimethylurea columns. The column stability was evaluated by means of the chromatographic parameters obtained for the separation of some compounds from the Neue test mixture, using apolar, polar and highly basic analytes.     

Effects of Adsorbed Polyaniline on Redox Process on MoO3 Surface

The effects exhibited by adsorbed conducting polyaniline on the redox process on a molybdenum oxide surface were studied. Thermogravimetric results indicate a 4% polyaniline deposition. Cyclic voltammograms of the adsorbed polymer on MoO3 show that polyaniline exerts remarkable effects on the molybdenum blue oxidation-reduction process, with oxidation and reduction potentials of 0.33 and 0.18 V, respectively. This effect strongly enhances the electrode response, and can be used as an important tool in qualitative and/or quantitative determinations of molybdenum in solution as well as in any substrate. Copyright 1999 Academic Press.     

Thermochemistry of Surfactant-Templating of USY Zeolite

With the aim of understanding the thermochemistry of the introduction of mesoporosity in zeolites by using surfactants, high temperature oxide melt solution calorimetry was used to determine the change in the enthalpy of formation of USY zeolite before and after the introduction of mesoporosity. Our results confirm that this process only slightly destabilizes the zeolite by the additional surface area. However, this can be overcome by the stabilizing effect of the interactions between the surfactant and the zeolite framework.