A novel direct method for preparation of aromatic polyimides via microwave-assisted polycondensation of aromatic dianhydrides and diisocyanates

Possibility of imide structure formation under microwave irradiation of molecules containing anhydride and isocyanate functional groups was investigated. The microwave-assisted polycondensation of aromatic diisocyanates and dianhydrides for preparation of polyimides was studied. The effect of microwave irradiation time and power, solvent nature, solid content of monomers, effect of catalyst, effect of polymerization reactor material and possibility of pressure development during polymerization, on the inherent viscosity of prepared polyimides were discussed. Experimental results showed that polymers obtained via this method had superior inherent viscosity and yield in comparison to the polymers obtained via conventional solution method.     

Superabsorbent hydrogel composites

A new cost‐effective approach to enhance gel strength of superabsorbent hydrogels was invented. Superabsorbent hydrogel composites (SHCs) were prepared through an optimized rapid solution polymerization of concentrated partially neutralized acrylic acid in the presence of a crosslinking agent under normal atmospheric conditions. Kaolin was used as an inorganic component in the polymerization process to strengthen the hydrogel products. FT‐IR spectroscopy was used to confirm grafting of acrylic chains on to the surface of kaolin particles. Morphology of the products was studied by scanning electron microscopy (SEM). Compared with the kaolin‐free hydrogel (control), kaolin caused a reduced equilibrium swelling and swelling rate as low as 17–31% and 19–29%, respectively. Kaolin, however, resulted in enhanced gel strength as high as 21–35% compared to the control. Differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) were used to study thermal properties of the composites. The SHCs exhibited higher thermal stability than the control. Meanwhile, changes in certain thermal transitions reconfirmed the chemical interaction of the acrylic chain with kaolin. These thermostabilized strengthened superabsorbent hydrogels may be considered as good candidates for agricultural application to retain more water under soil pressure. Copyright © 2003 John Wiley & Sons, Ltd.     

Molecular structure of an alkyl-side-chain polymer-water interface: origins of contact angle hysteresis

A new and direct approach to verify surface heterogeneity as the microscopic origin of contact-angle hysteresis is demonstrated. IR-visible sum-frequency-generation spectroscopy (SFG) was used to selectively probe the molecules at the interface of an alkyl-side-chain polymer [poly(vinyl n-octadecyl carbamate-co-vinyl acetate)] with water. The spectra indicate that in contact with water, the polymer surface is heterogeneous (having areas of differing surface energies). This evidence of surface heterogeneity supports the hysteresis observed in the advancing and receding contact angles of the polymer surface with water. The same measurements made for the chemically and structurally similar surface of an octadecyltrichlorosilane self-assembled monolayer indicates a homogeneous surface at the water interface. In this case, contact-angle hysteresis measurements implicate surface roughness as the cause of hysteresis. Atomic force microscopy measurements of roughness for these surfaces further support our conclusions. The polymer-water interface was probed using SFG at above-ambient temperatures, and an order-to-disorder transition (ODT) of alkyl side chains at the interface was observed, which closely follows the melting of crystalline side chains in the bulk. This transition explains the increased wettability of the polymer, by water, when the temperature is raised above the bulk melting temperature. Furthermore, the irreversibility of this ODT suggests that the disordered polymer-water interface is the thermodynamic equilibrium state, whereas the before-heating structure of this interface is a kinetically hindered metastable state.     

Infrared-visible sum frequency generation spectroscopic study of molecular orientation at polystyrene/comb-polymer interfaces

Surface-sensitive infrared-visible sum frequency generation spectroscopy (SFG) in total internal reflection geometry has been used to study the structure of poly(vinyl n-octadecyl carbamate-co-vinyl acetate) (PVNODC) or poly(octadecyl acrylate) (PA-18) in contact with a deuterated or hydrogenated polystyrene (dPS or hPS) layer. SFG spectra from the PVNODC (or PA-18)/hPS interface show methyl and methylene peaks corresponding to PVNODC (or PA-18) and phenyl peaks corresponding to the PS. Analysis suggests that the methyl groups are tilted at angles less than 30 degrees with respect to the surface normal. The presence of a strong methylene peak suggests the PVNODC alkyl side chains contain more gauche defects at the PS/PVNODC interface in comparison to PVNODC (or PA-18)/air interfaces. On heating, the SFG intensity from the PS/PA-18 interface drops sharply near the bulk melting temperature (T(m)) of PA-18. Interestingly, a similar drop in SFG signal is also observed for the PS phenyl groups. This demonstrates the ability of the phenyl group at the PS/PA-18 interface to rearrange itself upon the solid-to-liquid transition of the PA-18 alkyl side chain, at a temperature well below the bulk PS glass transition temperature. For PS/PVNODC interfaces, the drop in SFG intensity is gradual and in agreement with the three broad transitions of PVNODC observed in the bulk.     

Synthesis and properties of biodegradable elastomeric epoxy modified polyurethanes based on poly(ε-caprolactone) and poly(ethylene glycol)

Biodegradable polyurethane elastomers with potential for applications in medical implants with tunable degradation rate and physical properties were synthesized from reaction of epoxy terminated polyurethanes (EUP) with 1,6-hexamethylene diamine (HMDA) as curing agent. Poly(ε-caprolactone) (PCL) and poly(ethylene glycol) (PEG) as well as 1,6-hexamethylene diisocyanate (HDI) were used for preparation of isocyanate terminated polyurethanes which were subsequently blocked with glycidol to prepare EUPs. All materials were characterized by conventional methods, and their properties were studied fully. Results showed that elastomers based on PEG exhibit superior degradation rate and inferior mechanical properties in comparison to elastomers based on PCL. Optimum degradation rate and mechanical properties were obtained from elastomers made from mixture of PCL and PEG base EUPs.     

Formation of PdNiZn thin film at oil‐water interface: XPS study and application as Suzuki‐Miyaura catalyst

Nanosheet of PdNiZn and nanosphere of PdNiZn/reduced‐graphene oxide (RGO) with sub‐3 nm spheres have been successfully synthesized through a facile oil‐water interfacial strategy. The morphology and composition of the films were determined by X‐ray diffraction (XRD), X‐ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM), scanning electron microscopy (SEM), energy dispersive analysis of X‐ray (EDAX) and elemental mapping. In the present study, we have developed a method to minimize the usage of precious Pd element. Due to the special structure and intermetallic synergies, the PdNiZn and PdNiZn/RGO nanoalloys exhibited enhanced catalytic activity and durability relative to Pd nanoparticles in Suzuki‐Miyaura C‐C cross‐coupling reaction. Compared to classical cross‐coupling reactions, this method has the advantages of a green solvent, short reaction times, low catalyst loading, high yields and reusability of the catalysts.     

SOLVENT-FREE CONVERSION OF OXIRANES TO THIIRANES WITH THIOUREA

A simple and efficient method for the conversion of various oxiranes to the corresponding thiiranes using thiourea under solvent free conditions is described.