Cobalt promoted Ni/MgAl2O4 catalyst in lean methane catalytic oxidation

In the present research, magnesium aluminate spinel was prepared as catalyst support using a novel, facile, and efficient mechanochemical method. The Co-promoted catalysts with 20 wt.% of Ni were fabricated using an impregnation route and the samples were analyzed by the X-ray diffraction (XRD), N₂ adsorption/desorption (BET), temperature-programmed reduction and desorption (H₂-TPR and O₂-TPD), and field emission scanning electron microscopy (FESEM) tests. The results confirmed that all samples have a mesoporous structure with a high specific surface area and the presence of cobalt caused complete CH₄ oxidation at low temperatures, and no side reactions were observed. The results indicated that the 3%Co-20%Ni/MgAl₂O₄ catalyst was the optimal sample among the prepared catalysts, owing to the improvement of reduction features and oxygen mobility. The 50 and 90% of methane conversion was obtained at 530 and 600 °C, respectively. Also, the influence of calcination temperature, GHSV, and feed ratio was determined on the catalytic activity. The obtained outcomes revealed that the calcination temperature has a significant effect on the textural properties and catalytic efficiency. The sample calcined at 700 °C showed the weakest performance, which was related to the sintering of particles at high temperatures. The catalytic stability showed that the 3%Co-20%Ni/MgAl₂O₄ has acceptable stability during 600 min time of reaction.

Graphical abstract

     

Fully developed mixed convection in horizontal and inclined tubes with uniform heat flux using nanofluid

Fully developed laminar mixed convection of a nanofluid consists of water and Al₂O₃ in horizontal and inclined tubes has been studied numerically. Three-dimensional elliptic governing equations have been solved to investigate the flow behaviors over a wide range of the Grashof and Reynolds numbers. Comparisons with previously published experimental and numerical works on mixed convection in a horizontal and inclined tube are performed and good agreements between the results are observed. Effects of nanoparticles concentration and tube inclinations on the hydrodynamics and thermal parameters are presented and discussed. It is shown that the nanoparticles concentration does not have significant effects on the hydrodynamics parameters. Heat transfer coefficient increases by 15% at 4 Vol.% Al₂O₃. Skin friction coefficient continually increases with the tube inclination, but the heat transfer coefficient reaches a maximum at the inclination angle of 45°.     

Structure–retardation factor relationship of natural amino acids in two different mobile phases of RP-TLC

Abstract

Separation of amino acids (AAs) and their simple and inexpensive determination/identification is an interesting topic in biological and protein science, different food industries, and drug factories. Also, the presentation of the chromatographic behavior of compounds in a predictive model can be effective to estimate the structural/chemical properties of analyte and mobile phases. In this work for the first time, retardation factor (R_F) of 42 AAs in reversed-phase thin layer chromatography (RP-TLC) was modeled. Acetonitrile-sodium azide solution and 1,2 dioxane-sodium azide solution were two mobile phases which have been studied in this work. Results showed that the values of R_F are correlated with the structural properties of AAs and these properties had some similarities and differences in two noted mobile phases. For the TLC data in two mobile phases, five parametric linear models were suggested (R²_train = 0.93 and 0.97; R²_test = 0.93 and 0.99). The models were also evaluated with different statistical approaches. It was shown that increasing the sum of geometrical distances between N and O in AAs causes decreasing their R_F in RP-TLC using both mobile phases. Other structural effects of AAs on their separation in the desired RP-TLC system were also discussed.     

Development,In-Vitro Characterization and Preclinical Evaluation of Esomeprazole-Encapsulated Proniosomal Formulation for the Enhancement of Anti-Ulcer Activity

Objective: The present study aimed to develop and optimize esomeprazole loaded proniosomes (EZL-PNs) to improve bioavailability and therapeutic efficacy. Method: EZL-PNs formulation was developed by slurry method and optimized by 33 box-Bhekhen statistical design software. Span 60 (surfactant), cholesterol, EZL concentration were taken as independent variables and their effects were evaluated on vesicle size (nm), entrapment efficiency (%, EE) and drug release (%, DR). Furthermore, optimized EZL-PNs (EZL-PNs-opt) formulation was evaluated for ex vivo permeation, pharmacokinetic and ulcer protection activity. Result: The EZL-PNs-opt formulation showed 616 ± 13.21 nm of vesicle size, and 81.21 ± 2.35% of EE. EZL-PNs-opt exhibited negative zeta potential and spherical confirmed scanning electron microscopy. EZL-PNs-opt showed sustained release of EZL (95.07 ± 2.10% in 12 h) than pure EZL dispersion. The ex-vivo gut permeation result exhibited a significantly (p < 0.05) enhanced flux than pure EZL. The in vivo results revealed 4.02-fold enhancement in bioavailability and 61.65% protection in ulcer than pure EZL dispersion (43.82%). Conclusion: Our findings revealed that EZL-PNs formulation could be an alternative delivery system of EZL to enhance oral bioavailability and antiulcer activity.     

Formation of PdNiZn thin film at oil‐water interface: XPS study and application as Suzuki‐Miyaura catalyst

Nanosheet of PdNiZn and nanosphere of PdNiZn/reduced‐graphene oxide (RGO) with sub‐3 nm spheres have been successfully synthesized through a facile oil‐water interfacial strategy. The morphology and composition of the films were determined by X‐ray diffraction (XRD), X‐ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM), scanning electron microscopy (SEM), energy dispersive analysis of X‐ray (EDAX) and elemental mapping. In the present study, we have developed a method to minimize the usage of precious Pd element. Due to the special structure and intermetallic synergies, the PdNiZn and PdNiZn/RGO nanoalloys exhibited enhanced catalytic activity and durability relative to Pd nanoparticles in Suzuki‐Miyaura C‐C cross‐coupling reaction. Compared to classical cross‐coupling reactions, this method has the advantages of a green solvent, short reaction times, low catalyst loading, high yields and reusability of the catalysts.     

Simultaneous formation of platinum‐based nanocatalysts and degradation of dyes at oil/water interface: Comparative morphological and kinetic studies

To decrease the water pollution of textile industries with a large amount of toxic and non‐biodegradable colored dye effluents, an efficient technique is required to safely remove harmful pollutants. In this paper, the reaction between azo dyes and NaBH₄ catalyzed by nanoparticles (NPs) thin films has been studied. We report insitu degradation of methyl orange (MO) and methyl red (MR) by using Pt‐based thin films monitored by UV–Vis spectroscopy. We have synthesized different thin films such as Pt, PtPd, PtFeFe₂O₃, PtNi and PtAu films from Pt organometallic precursor in the MO and MR medium (dye degradation and NPs formation is happened simultaneously) and activity of these films were compared in the complete degradation of MO and MR dyes. Rate constants for the catalyzed reactions have been determined. PtPd NPs thin film has shown the highest rate constant for the degradation of MO and MR within only a few seconds due to its well‐ordered structure. Furthermore, the effect of presence of MO on the morphology of NPs was investigated.     

Two building blocks of microwave photonics filters in the presence of group delay ripple: a comparative survey

We have developed an analytic approach to investigate the effect of group delay ripple of the dispersive devices on the performance of two major building blocks of microwave-photonic filters. Firstly, performance of PM-based block in the presence of an arbitrary group delay ripple (GDR) is analyzed and compared with the ripple-free case to reveal the destructive effects of added group delay ripple. In the next step, we repeat the proposed approach for the AM-based one; again, the performance is compared with the ripple-free case. Two distortion metrics are also introduced to quantify this distortion. Comparison of the performance of two building blocks in the presence of group delay ripple unveils some interesting characteristics of microwave-photonic filters which have not been mentioned so far. We also add a general survey of two analyzed building blocks to present their respective most significant advantages and shortcomings. The simulated Optisystem results conform to our proposed analytical approach and verify the theoretical model.