零维到三维结构中三核铜自旋阻挫簇单元的磁构关系和反对称交换

量子自旋液体是最近几年刚被人们证实除铁磁体、反铁磁体之外的第三种磁性类型,因其有望解释高温超导的运行机制、改变计算机硬盘信息存储方式而在物理、材料等领域备受关注。自旋阻挫作为量子自旋液体的最小单元可能是解开量子自旋液体诸多问题的钥匙,所以在磁学、电学研究领域再一次成为人们研究的热点。基于文献报道的三核铜配合物[Cu3(μ3-OH)(μ-OPz)3(NO3)2(H2O)2]·CH3OH(1),我们合成了三维金属有机框架配合物{[Ag(HOPz)Cu3(μ3-OH)(NO3)3(OPz)2Ag(NO3)]·6H2O}n(2)(HOPz=甲基(2-吡嗪基)酮肟),并从自旋阻挫的角度对二者磁性质进行对比和详细分析。磁化率数据表明自旋间有很强的反铁磁相互作用和反对称交换。通过包含各向同性和反对称交换的哈密顿算符对两者磁学数据进行拟合并研究其磁构关系,所获最佳拟合参数为:配合物1:Jav=-426 cm^-1,g⊥=1.83,g∥=2.00;配合物2:Jav=-401 cm^-1,g⊥=1.85,g∥=2.00。     

超临界流体触媒作用下石墨-金刚石转变

 研究了超临界流体CO₂在石墨-金刚石转变中的触媒作用。实验中，采用Ag₂O作为流体触媒的先驱材料，在7.7 GPa压力下，Ag₂O在1 200 ℃分解成Ag和O₂，O₂与石墨套管在高温高压下反应形成CO₂超临界流体。研究结果表明，在7.7 GPa和1 500 ℃以上温度条件下，石墨在CO₂流体触媒的作用下可转变为金刚石晶体，在1 500～1 700 ℃温度范围内合成出的金刚石具有完好的八面体形貌，与天然金刚石的生长特征非常相似。     

93W合金有关力学参量的综合选评

 对93W合金材料进行了超声测量实验，并结合原有的超声测量结果进行了分析比较，提出了可以直接用冲击波速度关系式的三个系数c₀ 、λ和λ′来对钨合金的有关力学参量，如G₀、K₀、G₀′、K₀′等进行综合选评的方法。得到了一组对93W合金较为合理的力学参量推荐值。     

Soluble,saturated‐red‐light‐emitting poly(p‐phenylenevinylene) containing triphenylamine units and cyano groups

A conjugated poly(p‐CN‐phenylenevinylene) (PCNPV) containing both electron‐donating triphenylamine units and electron‐withdrawing cyano groups was prepared via Knoevenagel condensation in a good yield. Gel permeation chromatography suggested that the soluble polymer had a very high weight‐average molecular weight of 309,000. A bright and saturated red emission was observed under UV excitation in solution and film. Cyclic voltammetry showed that the polymer presented quasi‐reversible oxidation with a relatively low potential because of the triphenylamine unit. A single‐layer indium tin oxide/PCNPV/Mg–Ag device emitted a bright red light (633 nm). © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 3947–3953, 2004     

两个回归函数相等的Bootstrap检验

两个回归参数相等性检验一直是统计界感兴趣的问题之一．在这篇文章中，四个检验统计量被用于度量两曲线的差异，在原假设下统计量的分布采用向量数据的重复抽样来逼近，并给出了—些模拟结果．     

等离子体噻吩聚合膜的研究及I+注入的掺杂效应

以噻吩为单体,在等离子体环境中聚合成致密的有机膜。利用Rutherford背散射(RB2S)和质子弹性反冲(ERD)、傅里叶红外谱(FTIR)测定了膜的成分和结构;从近红外-可见-紫外光的反射和透射谱,运用传递矩阵方法研究了膜的光学性质;此外,还探讨了24keV的I⁺离子束的注入对等离子体噻吩聚合膜的掺杂效应。结果表明,注入层内电荷载流子的输运机理可用Mott的可变自由程跳跃(VRH)理论给以解释。 关键词：     

The influence of hard‐segments on two‐phase structure and shape memory properties of PCL‐based segmented polyurethanes

Poly(ε‐caprolactone)‐based segmented polyurethanes (PCLUs) were prepared from poly(ε‐caprolactone) diol, diisocyanates (DI), and 1,4‐butanediol. The DIs used were 4,4′‐diphenylmethane diisocyanate (MDI), 2,4‐toluenediisocyanate (TDI), isophorone diisocyanate (IPDI), and hexamethylene diisocyanate (HDI). Differential scanning calorimetry, small‐angle X‐ray scattering, and dynamic mechanical analysis were employed to characterize the two‐phase structures of all PCLUs. It was found that HDI‐ and MDI‐based PCLUs had higher degree of microphase separation than did IPDI‐ and TDI‐based PCLUs, which was primarily due to the crystallization of HDI‐ and MDI‐based hard‐segments. As a result, the HDI‐based PCLU exhibited the highest recovery force up to 6 MPa and slowest stress relaxation with increasing temperature. Besides, it was found that the partial damage in hard‐segment domains during the sample deformation was responsible for the incomplete shape‐recovery of PCLUs after the first deformation, but the damage did not develop during the subsequent deformation. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 557–570, 2007     

黄芪成分F3新制剂的工艺监测

对黄芪成分F3新制剂中多糖、蛋白质进行了工艺监测，多糖提取达99．2％，蛋白质≤0．2％，符合黄芪成分F3的质量标准要求，达到了选择最佳提取工艺的目的，结果令人满意。     

Phenylene vinylene‐based electroluminescent polymers with electron transport block in the main chain

We report a new route for the design of soluble phenylene vinylene (PV) based electroluminescent polymers bearing electron‐deficient oxadizole (OXD) and triazole (TZ) moieties in the main chains with the aryloxy linkage. Both series of the PV‐based polymers were prepared by Wittig reaction. By properly adjusting the OXD and/or TZ content through copolymerization, we can achieve an enhanced balance of hole‐ and electron injections, such that the device efficiency is significantly improved. Light‐emitting diodes fabricated from P1, P2, P3, P4, P5, P6, and P7 with the configuration of Indium–Tin Oxide (ITO)/Poly (styrene sulfonic acid) doped poly (ethylenedioxythiophene) (PEDOT)/polymer/Ca/Al, emit bright green light with the maximum peak around 500 nm. For the device using the optimal polymer (P4) as emitting layer, a maximum brightness of 1300 cd/m² at 20 V and a maximum luminance efficiency of 0.325 cd/A can be obtained. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3469–3478, 2006     

聚乙烯单晶的退火效应

用混合晶红外光谱法和ＳＡＸＳ、ＤＳＣ和ＬＡＭ等方法研究了聚乙烯单晶在７５℃、９０℃和１０５℃退火前后的结构变化，发现在９０℃以下和１０５℃以上退火，遵循不同的退火机制