Photorefractive Four-Wave Mixing Switches Utilizing Pockels Effect -Longitudinal and Lateral Switches-

We carried out detailed calculations for photorefractive wave-mixing switches based on one of three crystals with high electro-optic coefficients, namely, BaTiO₃, Strontium Barium Niobate (SBN (0.75)), and Potasium Sodium Strontium Barium Niobate (KNSBN). A comparison of results for the three crystals shows that a 0_-cut BaTiO³ crystal is suitable for a longitudinal switch and requires a voltage of about 80 for a 2-mm-thick crystal to induce sufficient phase mismatch. The electrodes must be transparent for the incident and diffracted beams. A 45_-cut SBN (0.75) crystal, however, is suitable for a lateral switch and requires a voltage of about 150 for a 1-mm-wide crystal. The electrodes do not need to be transparent.     

Depolymerization Study of Pakistani Lignite Coal Influence of Pre‐treatments on Product Slate

Influence of pretreatments, i.e., demineralization and pre‐soaking in some solvents on the yields of liquefied products obtained from hydro‐depolymerization of Pakistani coal in a pool of hydrogen has been discussed. Results of hydrogenation experiments demonstrated that demineralizing the coal sample prior to liquefaction caused the yields to decrease compared with the virgin coal samples. The contribution of mineral matter of coal has been evaluated by comparing the yields of liquid products of virgin and leached samples. Increase in the yields obtained from the hydrogenation experiments of swollen coal samples was not satisfactorily significant.     

Susceptibility to Effects of UVB Irradiation on Induction of Contact Sensitivity, Relevance of Number and Function of Langerhans Cells and Epidermal Macrophages

Sensitization on skin exposed to acute low-dose UVB irradiation separates normal humans into two phenotypically distinct groups: One group, following sensitization on UVB-irradiated skin, develops contact sensitivity, designated UVB resistant (UVB-R) and the second group, following sensitization on UVB-irradiated skin, fails to develop contact sensitivity, designated UVB susceptible (UVB-S). To investigate whether UVB susceptibility in humans is related to antigen-presenting activity in the skin we studied the effect of UVB irradiation on the number and function of the epidermal antigen-presenting cells in volunteers identified as UVB-R and UVB-S. Single cell suspensions of epidermal cells from control skin and skin exposed to 3 minimal erythema doses (MED) of UVB 3 days previously were stained for Langerhans cells (CD1a+HLA-DR+) and epidermal macrophages (CD1a-HLA-DR+). The UVB exposure of the skin significantly decreased the percentage of Langerhans cells (UVB-R: n = 7, P < 0.02, UVB-S: n = 6, P < 0.03) and increased the percentage of epidermal macrophages (UVB-R: n = 7, P < 0.03, UVB-S: n = 6, P < 0.03) however to the same degree in both the UVBR and the UVB-S group. To study the effect on Langerhans cell alloreactivity, epidermal cells were harvested immediately after UVB irradiation. However, in both UVB-R and UVB-S subjects the Langerhans cell alloreactivity was blocked to the same degree immediately after UVB irradiation compared to nonirradiated epidermal cells. To determine the effect of UVB irradiation on epidermal macrophages, epidermal cells were harvested 3 days after UVB irradiation. Irradiated epidermal cells from both UVB-R and UVB-S subjects demonstrated a strong antigen-presenting capacity compared to epidermal cells from control skin leading to activation of T cells that mainly secrete interferon (1FN)-γ and not interleukin (IL)-4. In conclusion we found that UVB susceptibility was not correlated with the number of Langerhans cells or epidermal macrophages in the skin at the same time of sensitization. Neither was it correlated with the capacity of Langerhans cells nor UVB-induced epidermal macrophages to activate T cells in vitro.     

Stainless steel modified with poly(ethylene glycol) can prevent protein adsorption but not bacterial adhesion

The surface of AISI 316 grade stainless steel (SS) was modified with a layer of poly(ethylene glycol) (PEG) (molecular weight 5000) with the aim of preventing protein adsorption and bacterial adhesion. Model SS substrates were first modified to introduce a very high density of reactive amine groups by the adsorption of branched poly(ethylenimine) (PEI) from water. Methoxy-terminated aldehyde-poly(ethylene glycol) (M-PEG-CHO) was then grafted onto the PEI layers using reductive amination at the lower critical solution temperature (LCST) of the PEG in order to optimize the graft density of the linear PEG chains. The chemical composition and uniformity of the surfaces were determined using X-ray photoelectron spectroscopy (XPS) and time-of-flight static secondary ion mass spectrometry (ToF-SSIMS) in the imaging mode. The effects of PEI concentration and different substrate pre-cleaning methods on the structure and stability of the final PEG layer was examined. Piranha solution proved to be the most effective method for removing adventitious hydrocarbon contamination, compared to cleaning with ultrasonication in organic solvents, and was the SS substrate that produced the most stable and thickest PEI layer. The surface density of PEI was shown to increase with increasing PEI concentration (up to 30 mg/ml), as determined from XPS measurements, and subsequently produced the PEG layer with the highest density of attached chains. In model experiments using β-lactoglobulin no protein adsorption was detected on the optimized PEG surface as determined by XPS and ToF-SSIMS analysis. However, neither the adhesion of a Gram-negative (Pseudomonas sp.) nor a Gram-positive (Listeria monocytogenes) bacterium was affected by the coating as equal numbers adhered to all surfaces tested. Our results show that preventing protein adsorption is not a prerequisite stopping bacterial adhesion, and that other mechanisms most likely play a role.     

Hyperfine structure studies of Tantalum

A narrow bandwidth ring dye laser pumped by an argon ion laser has been used to investigate the hyperfine structure of the even and odd parity levels of tantalum by optogalvanic spectroscopy in the wavelength range 5640 to 6050 Å. Seventeen transitions have been observed and eight of these have not been reported in the literature so far. These transitions involve 27 levels with 15 odd and 12 even parity configurations. The magnetic dipole hyperfine interaction constants A and the electric quadrupole interaction constants B for these levels have been computed and compared with the data available in literature. The results for the levels at 34799.71 cm^?1, 26960.46 cm^?1 and 19657.78 cm^?1 are reported for the first time.     

Pseudochelin A,a siderophore of Pseudoalteromonas piscicida S2040

A new siderophore containing a 4,5-dihydroimidazole moiety was isolated from Pseudoalteromonas piscicida S2040 together with myxochelins A and B, alteramide A and its cycloaddition product, and bromo- and dibromoalterochromides. The structure of pseudochelin A was established by spectroscopic techniques including 2D NMR and MS/MS fragmentation data. In bioassays selected fractions of the crude extract of S2040 inhibited the opportunistic pathogen Pseudomonas aeruginosa. Pseudochelin A displayed siderophore activity in the chrome azurol S assay at concentrations higher than 50 μM, and showed weak activity against the fungus Aspergillus fumigatus, but did not display antibacterial, anti-inflammatory or anticonvulsant activity.     

Ab-initio calculations of structural,electronic,and optical properties of Zn_3(VO_4)_2

The structural, electronic, and optical properties of Zn_3(VO_4)_2 are investigated using full potential linearized augmented plane wave(FP-LAPW) method within the framework of density functional theory(DFT). Various approaches are adopted to treat the exchange and correlation potential energy such as generalized gradient approximation(GGA),GGA+U, and the Tran–Blaha modified Becke–Johnson(TB-mBJ) potential. The calculated band gap of 3.424 eV by TB-mBJ is found to be close to the experimental result(3.3 eV). The optical anisotropy is analyzed through optical constants,such as dielectric function and absorption coefficient along parallel and perpendicular crystal orientations. The absorption coefficient reveals high absorption(1.5 × 10~(6) cm~(-1)) of photons in the ultraviolet region.