Structural developments in synthetic rubbers during uniaxial deformation by in situ synchrotron X‐ray diffraction

The molecular orientation and strain‐induced crystallization of synthetic rubbers—polyisoprene rubber, polybutadiene rubber, and butyl rubber [poly(isobutylene isoprene)]—during uniaxial deformation were studied with in situ synchrotron wide‐angle X‐ray diffraction. The high intensity of the synchrotron X‐rays and the new data analysis method made it possible to estimate the mass fractions of the strain‐induced crystals and amorphous chain segments in both the oriented and unoriented states. Contrary to the conventional concept, the majority of the molecules (50–75%) remained in an unoriented amorphous state at high strains. Each synthetic rubber showed a different behavior of strain‐induced crystallization and molecular orientation during extension and retraction. Our results confirmed the occurence of strain‐induced networks in the synthetic rubbers due to the inhomogeneity of the crosslink distribution. The strain‐induced networks containing microfibrillar crystals and oriented amorphous tie chains were responsible for the ultimate mechanical properties. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 956–964, 2004     

Design and synthesis of labeling reagents (MS probes) for highly sensitive electrospray ionization mass spectrometry and their application to the detection of carbonyl, alcohol, carboxylic acid and primary amine samples.

Novel labeling reagents, called MS probes, which possess a positively charged quaternary amine moiety and can transform a neutral analyte into a charged compound by simply mixing with the analyte and allowing the mixture to stand from several minutes to 30 min at room temperature or while heating to 50 degrees C, were designed and synthesized for the highly sensitive detection of carbonyl, alcohol, carboxylic acid and primary amine samples by electrospray ionization mass spectrometry (ESI-MS). The positively charged products can be detected with high sensitivity in an ESI-MS system, which is the most popular liquid MS instrument. All of the labeled products showed a remarkably large increase in the molecular-ion peak abundance detection sensitivity of over 500-fold at picomolar concentration levels compared to that of unlabeled analytes in an ESI-MS system. These MS probes, used together with liquid MS detection, are widely applicable as a convenient method for the highly sensitive detection of less than picomolar levels of analytes, and therefore greatly enhance the power of ESI-MS analysis.     

Cerasome as an Organic-Inorganic Vesicular Nanohybrid: Characterization of Cerasome-Forming Lipids having a Single or a Dual Trialkoxysilyl Head

Morphological characterization of the organic-inorganic vesicular nanohybrids, Cerasomes, was performed in aqueous media from two aspects. Firstly, a novel Cerasome-forming lipid having two triethoxysilyl groups in the head moiety was synthesized and the physical property of the Cerasome was investigated. While the morphological stability of the Cerasomes, as evaluated from the vesicular collapse behavior against a micelle-forming nonionic surfactant, Triton-X 100, was extremely higher than that of the conventional phospholipid liposome, the stabilities were comparable to each other for the Cerasomes derived from the dual- and single-head lipids. On the other hand, the surface property of the Cerasome formed with the dual-head lipid more closely resembled the colloidal silica particles rather than that derived from the single-head lipid, as suggested by zeta-potential measurements. Secondly, the effect of the media pH on the morphological stability of the Cerasome formed with the single-head lipid was evaluated and appeared as a time difference in obtaining the morphological stability of the Cerasome. These morphological characteristics of the Cerasomes could be mainly owing to the development of the siloxane network on the vesicular surface.     

Interfacial adsorption state of protonated lipophilic porphyrins in a liquid-liquid system by using reflection spectrometry.

Analysis by reflection spectrometry was performed to clarify the interfacial adsorption of protonated lipophilic tetraphenylporphyrin derivatives in a dodecane-aqueous sulfuric acid system, and to confirm the utility of partial reflection spectroscopy. Interfacial adsorption was not observed for porphyrins substituted at the 2,6 positions of meso-phenyl groups, suggesting that the substituents prevent porphyrins from forming aggregates by steric hindrance. Polymorphous J-aggregates of acid dications were produced by tetra-p-tolylporphyrin with a saturated interfacial molecular density of 1.0 x 10(-10) mol cm(-2), which could yield 48 degrees as a mean tilting angle of the pyrrole ring plane from the interface normal. Partial-reflection spectrometry can provide sensitive detection and molecular orientation analysis of interfacial adsorbates.     

Wavelength dependence in photochemical vapor deposition of aluminum film using dimethylaluminum hydride

In photochemical vapor deposition of aluminum film on silicon using dimethylaluminum hydride, (CH₃)₂AlH, a surface reaction dominated below a (CH₃)₂AlH pressure of 0.3 m Torr at 200°C, which was induced only with the 160 nm band emitted from a deuterium lamp. A gas-phase reaction occurred above 0.3 mTorr at 200°C, which could be induced by both 160 nm and 240 nm emission bands from the lamp. To distinguish between surface ad gas-phase reactions, a thickness profile was used. At 240°C the surface reaction could be induced even by the 240 nm band, while the deposits formed under illumination of the two bands were thinner than those obtained with only the 240 nm band, indicating occurrence of vacuum ultraviolet (VUV)-enhanced desorption. The mechanism responsible for the observed wavelength dependence in unclear. The electrical resistivity of the films deposited at 200°C was 4.5 μΩ cm, which did not change with wavelength.     

Major-to-ultratrace elements in bone-marrow fluid as determined by ICP-AES and ICP-MS.

The major-to-ultratrace elements in human bone-marrow fluid were determined by ICP-AES (inductively coupled plasma atomic emission spectrometry), and ICP-MS (inductively coupled plasma mass spectrometry). The bone-marrow fluid sample was centrifuged prior to acid digestion to exclude the bone piece from bone marrow, and then digested with nitric acid. As a result, 20 elements could be determined over the concentration range from 1610 microg g(-1) for Na to 0.00043 microg g(-1) for W. It was found that Fe, Zn and Sb were enriched by ca. 264-, 7- and 15-fold, respectively, in bone-marrow fluid, compared to those in human blood serum. Alkali metals (K, Rb, Cs), except for Na, were also significantly enriched in bone-marrow fluid. Furthermore, the concentrations of various elements, such as Fe, P, Al, Zn, Cu, Se, Zr, Sn, Ag and W, were significantly higher than those in open seawater.     

Synthesis of spherical and hemispherical sugar‐containing poly(ornithine) dendrimers

A novel sugar‐containing poly(ornithine) dendrimer is synthesized for possible antigen delivery and related applications. The dendrimer contains an ornithine dendron as interior scaffolding and oligosaccharides on the periphery, which provide an attachment site for a peptide antigen. Maltose or lactose is bound to both hemispherical and spherical poly(ornithine) dendrimer generation 3 (G3) by reductive amination between its reducing end and the peripheral amino group of the dendrimer using a borane‐pyridine complex in a buffer solution at 50 °C. The degree of substitution of sugar is changed by varying the molar ratio of sugar to dendrimer. When the surface of spherical poly(ornithine) dendrimer G3 is modified by binding β‐alanine to the 16 amino groups, highly substituted maltose‐ or lactose‐β‐alanine‐poly(ornithine) dendrimer G3 is obtained in high yield after 7 days of reaction. The structures of these sugar‐containing dendrimers are characterized by NMR and matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrometry analyses. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 1400–1414, 2004     

Viscoelasticity and birefringence of polyisoprene

The complex Young's modulus, E^*(ω), and the complex strain-optical coefficient, O^*(ω), which is the ratio of the birefringence to the strain, were measured for polyisoprene (PIP) over a frequency range of 1 ～ 130 Hz and a temperature range of 22 ～ ?100°C. The imaginary part of O^*, O″, was positive at low frequencies and negative at high frequencies. The real part, O′, was always positive and showed a maximum. The complicated behavior of O^* could be understood by the assumption that E^* = E_R^* + E_G^* and O^* = C_RE_R^* + C_GE_G^*, where E_R^* and E_G^* were complex quantities and C_R and C_G were constants. The C_R value, equal to the ordinary stress-optical coefficient measured in the rubbery plateau zone, was 2.0 × 10^?9 Pa^?1. The C_G value, defined as the ratio O″/E″ in the glassy zone, was ?1.1 × 10^?11 Pa^?1. The E_G^*, which was the major component of E^* in the glassy zone, showed almost the same frequency dependence as that of polystyrene and polycarbonate. The E_R^*, which was dominant in the rubbery zone, was described well by the bead-spring theory. The temperature dependence of the E_G^* was stronger than that of the E_R^*. This difference caused the breakdown of the thermorheological simplicity for E^* and O^* around the glass-to-rubber transition zone. © 1995 John Wiley & Sons, Inc.