Copolymerization of optically active N-bornylmaleimide with vinyl monomers

Optically active N-bornylmaleimide (NBMI) was copolymerized with styrene, methyl methacrylate, and vinylidene chloride with a free-radical catalyst to obtain optically active copolymers. The monomer reactivity ratios for the radical copolymerization of NBMI (M₂) with styrene, methyl methacrylate, and vinylidene chloride were: ST-NBMI, r₁ = 0.13, r₂ = 0.05; MMA-NBMI, r₁ = 2.02, r₂ = 0.16; VCl₂-NBMI, r₁ = 1.15, r₂ = 0.47. The Q-e values for NBMI were Q₂ = 0.48 and e₂ = +1.47. The specific rotation and optical rotatory dispersion of these copolymers were measured. The correlation between the specific rotation and composition of these copolymers was not linear. The value of λ_c for each copolymer was independent of the copolymer composition and the comonomer, being 260 mμ for the St-NBMI system, 262 mμ for the MMA-system, and 260 mμ for the VCl₂-NBMI system. The effects of solvents and temperature on the specific rotation of these copolymers were investigated.     

Asymmetric induction copolymerization. Cationic copolymerization of l-menthyl vinyl ether with indene and acenaphthylene

l-Menthyl vinyl ether (l-MVE) was homopolymerized and copolymerized with the monomers indene (IN) and acenaphthylene (ANp) by BF₃OEt₂ as a catalyst. The chiral menthyl substituent was cloven from the homopolymers and copolymers using dry-hydrogen bromide gas. After the removal of optically active menthyl group, poly(vinyl alcohol) (PVA) from l-MVE homopolymer was optically inactive, and copolymers (VA-IN, VA-ANp) from l-MVE-IN and l-MVE-ANp copolymers were still optically active. Hence, in the case of l-MVE homopolymer, it was concluded that asymmetric induction in the polymer main chain can only produce pseudoasymmetry. In the case of l-MVE-IN and l-MVE-ANp copolymers, it was found that asymmetric induction proceeded in the copolymer main chain and was caused by the influence of chiral menthyl group.     

Comparison of the compact dry TC method with the standard pour plate method (AOAC official method 966.23) for determining aerobic colony counts in food samples: Performance-tested method

Compact Dry TC qualifies as a rapid method kit for determining aerobic colony counts in foods. The plates are presterilized and contain culture medium and a cold-soluble gelling agent. The medium is rehydrated by inoculating 1 mL diluted sample into the center of the self-diffusible medium and allowing the solution to diffuse by capillary action. The plates can then be incubated and the colonies counted without any additional steps. The Compact Dry TC method was validated with 5 different raw meats. The performance tests were conducted at 35 degrees and 30 degrees C. In all required performance studies, no apparent differences were observed between the Compact Dry TC method and the Standard Pour Plate method (AOAC Official Method 966.23) for the detection level of aerobic microorganisms. For the accuracy claim (n = 60), a correlation factor of r2(35) = 0.9977 (35 degrees C) and r2(30) = 0.9932 (30 degrees C) could be assigned, as stated in the application for "Performance Tested Method." Quality consistency and storage robustness studies, showed no significant variations in plate count results with different production lots or plates of diverse storage age.     

Prospects of Sol-Gel Process for Spectral Hole-Burning Glasses

Persistent spectral hole burning was studied in Eu³⁺ ions-doped Al₂O₃-SiO₂ glass prepared by a sol-gel method. The gel synthesized by the hydrolysis of Si- and Al-alkoxides and EuCl₃·6H₂O was heated in air and hydrogen gas atmospheres. For the glass heated in air to contain OH bonds, the hole was formed by the photoinduced rearrangement of the OH bonds surrounding the Eu³⁺ ions, and was thermally refilled and erased above 200 K. On the other hand, the glass heated in hydrogen gas showed the hole spectrum above 200 K. It was found that the hole depth was independent of the temperature and was 7% of the total intensity at room temperature. The proposed mechanism was the electron transfer between the Eu³⁺ ions and the defect centers formed in glass matrix.     

Polymerization of methyl methacrylate under ultrasonic irradiation. Part IV. Effect of ultrasonic irradiation on Grignard catalyst and stereoregularity of the polymers produced in dioxane–tetrahydrofuran mixed solvent

Two series of polymerization of methyl methacrylate with Grignard reagent in dioxane—tetrahydrofuran mixed solvent was carried out under ultrasonic irradiation. In series A, catalyst was added to the mixture of monomer and solvent, and in series B, catalyst was previously mixed with solvent. The effect of ultrasonic irradiation on Grignard catalyst and the microstructure in reacting sites were discussed on the basis of the stereoregularity of the polymers produced. The stereoregularity of the polymers in series A was higher than that in series B. The effect of ultrasonic irradiation on the stereoregularity was completely reversed in series A and B and it increased in the former and decreased in the latter. It was, therefore, assumed that ultrasonic irradiation affected the microstructure in the reacting sites in series A, while it increased the relative amount of R₂Mg which gave polymers with poor stereoregularity in series B.     

Hydrogen Gas Sensing of High Electrical Conducting-P2O5-SiO2 Glasses Prepared by Sol-Gel Process

High proton-conducting P₂O₅-SiO₂ glass was applied to the electrolyte of the hydrogen concentration cell for hydrogen gas sensing. 5P₂O₅·95SiO₂ glass was prepared using the sol-gel method and its electrical conductivity and electromotive force were measured at 50°C as a function of both the ambient humidity and hydrogen gas concentration. The electrical conductivities increased with increasing humidity and reached 10^–2 S/cm at 90% relative humidity. The electromotive force of the hydrogen concentration cell, where the glass was used as a membrane, showed good Nernstian response to hydrogen pressure in the high relative humidity region.     

Optically active copolyamides by melt and solution condensation polymerization

The melt and solution condensation copolymerization of nylon salts which were prepared from d-camphoric acid and adipic acid with hexamethylenediamine were carried out, and optically active copolyamides were obtained. The copolyamides obtained had a positive specific rotation. The specific rotations for the copolyamides increased with increasing content of d-camphoryl units in the copolymers. The optical rotatory dispersion of the copolyamides had positive curves and were found to fit the simple Drude equation. The λ_c values of the polymers obtained by the melt and solution condensation polymerization were 241 mμ and 245 mμ, respectively.     

Radiation-induced addition reaction of carbon tetrachloride onto 1,2-polybutadiene

The γ-ray-induced addition reaction of carbon tetrachloride onto syndiotactic 1,2-polybutadiene film and liquid 1,2-polybutadiene was carried out at room temperature. In the film gelation was pronounced and the rate of addition increased as the crystallinity of the polymer decreased. In the liquid gelation, which makes the polymer insoluble in carbon tetrachloride, did not take place, although a definite crosslinking reaction was noticed. In this case the appearance of the product changed from a viscous liquid to a white powder as the reaction proceeded. Its structure was compared with that of chlorinated 1,2-polybutadiene. The addition of carbon tetrachloride to the vinyl group in liquid 1,2-polybutadiene caused an anti-Markownikoff-type reaction and was accompanied by an unexpectedly large vinyl depletion in the polymer. The total decrease in the vinyl group was found to be much larger than that brought about by the addition of carbon tetrachloride. This discrepancy was attributed to a cyclization and crosslinking reaction ascribed to the vinyl group bound by the main chain. Cyclization and crosslinking were less noticeable in the chlorination than in the carbon tetrachloride.     

Identification of Site-Specific Degradation in Bacterially Expressed Human Fibroblast Growth Factor 4 and Generation of an Aminoterminally Truncated,Stable Form

Fibroblast growth factor 4 (FGF4) is considered as a crucial gene for tumorigenesis in humans and the development of mammalian embryos. The secreted, mature form of human FGF4 is thought to be comprised of 175 amino acid residues (proline³² to leucine²⁰⁶, Pro³²-Leu²⁰⁶). Here, we found that bacterially expressed, 6× histidine (His)-tagged human FGF4 (Pro³²-Leu²⁰⁶) protein, referred to as HishFGF4, was unstable such as in phosphate-buffered saline. In these conditions, site-specific cleavage, including between Ser⁵⁴ and Leu⁵⁵, in HishFGF4 was identified. In order to generate stable human FGF4 derivatives, a 6× His-tagged human FGF4 (Leu⁵⁵-Leu²⁰⁶), termed HishFGF4L, was expressed in Escherichia coli. HishFGF4L could be purified from the supernatant of cell lysates by heparin column chromatography. In phosphate-buffered saline, HishFGF4L was considered as sufficiently stable. HishFGF4L exerted significant mitogenic activities in mouse embryonic fibroblast Balb/c 3T3 cells. In the presence of PD173074, an FGF receptor inhibitor, the growth-stimulating activity of HishFGF4L disappeared. Taken together, we suggest that HishFGF4L is capable of promoting cell growth via an authentic FGF signaling pathway. Our study provides a simple method for the production of a bioactive human FGF4 derivative in E. coli.