Studies on photoinduced effects in pulse-electrodeposited Ag/Hg-1212/CdSe hetero-nanostructures

Metal/superconductor/semiconductor (Ag/Hg-1212/CdSe) hetero-nanostructures have been fabricated using pulse-electrodeposition technique and are characterized by X-ray diffraction (XRD), full-width at half-maximum (FWHM) and scanning electron microscopy (SEM) studies. The junction capacitance of Ag/Hg-1212, Hg-1212/CdSe and Ag/Hg-1212/CdSe heterojunctions is measured in dark and under laser irradiation at room temperature. The nature of the junction formed and built-in-junction potentials were determined. The increase in carrier concentration across the junction due to photo-irradiation has been observed.     

Effect of laser irradiation of C-V characteristics of electrodeposited Ag/Tl-2223/CdSe hetero-nanostructures

One of the innovative technological directions for the high-temperature superconductors has been persued by fabricating the heteroepitaxial multilayer structures such as superconductor-semiconductor heterostructures. In the present investigation, metal/superconductor/semiconductor (Ag/Tl-2223/CdSe) hetero-nanostructures have successfully been fabricated using dc electrodeposition technique and were characterized by X-ray diffraction (XRD), full-width at half-maximum (FWHM) and scanning electron microscopy (SEM) studies. The measurement of junction capacitance as a function of biasing voltage was used for the estimation of junction built-in-potential (V _D) and to study the charge distribution in a heterojunction. The Mott-Schottky plots were measured for each junction in dark and under the photo-irradiation. The effect of laser irradiation on C-V characteristics of hetero-nanostructure has been studied.     

Deformation and failure mechanism of secondary cell wall in Spruce late wood

The deformation and failure of the secondary cell wall of Spruce wood was studied by in-situ SEM compression of micropillars machined by the focused ion beam technique. The cell wall exhibited yield strength values of approximately 160 MPa and large scale plasticity. High resolution SEM imaging post compression revealed bulging of the pillars followed by shear failure. With additional aid of cross-sectional analysis of the micropillars post compression, a model for deformation and failure mechanism of the cell wall has been proposed. The cell wall consists of oriented cellulose microfibrils with high aspect ratio embedded in a hemicellulose-lignin matrix. The deformation of the secondary wall occurs by asymmetric out of plane bulging because of buckling of the microfibrils. Failure of the cell wall following the deformation occurs by the formation of a shear or kink band.     

Characterization of Irradiation Damage of Ferritic ODS Alloys with Advanced Micro-Sample Methods

Oxide dispersion strengthened (ODS) steels are candidate materials for advanced electric energy and heat generation plants (nuclear, fossil). Understanding the degradation of mechanical properties of these alloys as a result of service exposure is necessary for safe design. For advanced nuclear applications combinations of temperature, irradiation and stress are important damage conditions. They are studied either with neutron irradiated samples (often highly active) or with ion-irradiated samples (irradiation damage often limited to only a few micrometer deep areas). High activity of samples and limited sample volume claim to subsized samples like nano-indentation, micro-pillar compression or thin strip creep testing. Irradiation hardening and irradiation creep were studied with these methods. Ferritic ODS steels with 19% chromium were investigated. The materials were studied in qualities differing in grain sizes and in sizes of the dispersoids. Irradiation was performed in an accelerator using He-ions. Irradiation damage profiles could be well analyzed with indentation. Yield stress determined with compression tests of single-crystal micropillars was well comparable with tension tests performed along the same crystallographic orientation. Irradiation creep of samples with different sizes of dispersoids revealed only a small influence of particle size being is in contrast with thermal creep but consistent with expectations from other investigations.     

玫瑰红与介孔二氧化硅生物光敏复合体的激发态性质

以光动力治疗药物玫瑰红( Rose Bengal,RB)与孔径为2.7nm的介孔二氧化硅MCM-41为主体材料进行结构组装,制备了具有生物光敏功能的介孔复合载体.对介孔复合载体的性质进行了表征,通过紫外吸收和荧光光谱对玫瑰红RB在介孔孔道内的光学性质进行了分析.由于介孔道表面与RB的相互作用,不同结构和性质的内孔道中的...     

Development and validation of liquid chromatographic and ultraviolet derivative spectrophotometric methods for determination of epinastine hydrochloride in coated tablets

High-performance liquid chromatographic (LC) and ultraviolet derivative spectrophotometric (UVD) methods were developed and validated for the quantitative determination of epinastine hydrochloride in coated tablets. LC was performed on a reversed-phase RP-18 column with a mobile phase composed of 0.3% triethylamine (pH adjusted to 4.0 with 10% orthophosphoric acid)-methanol (60 + 40, v/v). The first-order derivative method was performed at 243.8 nm using HCI and methanol as the solvent. The methods were validated according to U.S. Pharmacopoeia and International Conference on Harmonization guidelines. The statistical analysis by Student's t-test showed no significant difference between the results obtained by the 2 methods. The proposed methods were found to be simple, rapid, precise, accurate, robust, and sensitive, allowing perfect interchange. The LC and UVD methods can be used in the routine quantitative determination of the epinastine hydrochloride in coated tablets.     

High Precision Diamond Machining of Hybrid Sol-Gel Coatings

Flexible and economic production of complex reflective optical elements is achieved by high-precision machining of aluminum and copper with diamond tools. There is also an increasing demand for complex refractive optical elements like micro lens arrays, Fresnel lenses or prismatic surfaces on silicon wafers or metallic surfaces. For the production of these optical elements, hybrid sol-gel coatings based on methacryloxypropyltrimethoxysilane (MATMS) and zirconium (IV) tetra n-propoxide (ZTP) were deposited on aluminum substrates by spin-coating. The influence of the rotational velocity and the chemical sol composition on the coating thickness was determined. The hardness and elastic modulus of these coatings was measured as a function of the chemical composition. The machining characteristics of these coatings were investigated by high precision turning and fly cutting with diamond tools of different geometry. The resulting surface finish obtained was determined as a function of the machining parameters.     

环形区域上Zernike模式法波前重构

 针对激光技术领域常见的环形激光光束,利用圆域Zernike多项式和环域Zernike多项式进行模式法波前重构,结果显示,如果环形激光光束波前相位畸变主要由低空间频率成分组成,则可以直接利用圆域Zernike多项式进行波前重构;如果环形激光光束波前相位畸变含有较多的高阶频率成分,则利用环域Zernike多项式进行波前重构。