STABILITY ANALYSIS OF A CAPACITIVE FGM MICRO-BEAM USING MODIFIED COUPLE STRESS THEORY

Based on the Modified Couple Stress Theory,a functionally graded micro-beam under electrostatic forces is studied.The FGM micro-beam is made of two materials and material properties vary continuously along the beam thickness according to a power-law.Dynamic and static pull-in voltages are obtained and it is shown that the static and dynamic pull-in voltages for some materials cannot be obtained using classic theories and components of couple stress must be taken into account.In addition,it is shown that the values of pull-in voltages depend on the variation through the thickness of the volume fractions of the two constituents.     

甲烷氧化偶联锂/氧化镁催化剂和纳米催化剂

采用初湿浸渍和溶胶凝胶法分别制备了Li/MgO催化剂和Li/MgO纳米催化剂. 比较两种Li/MgO催化剂对于甲烷氧化偶联反应的催化性能. 采用X射线衍射、BET吸附和透射电镜进行了表征.在973-1073 K和总压力为101 kPa下对催化剂进行了测试. 实验结果表明,Li/MgO纳米催化剂比普通催化剂对于甲烷氧化偶联反应表现为更高的甲烷转换率,较高选择性和较高的的主要产品(乙烷和乙烯)的产率.     

Pure parametric excitation of a micro cantilever beam actuated by piezoelectric layers

This paper deals with the stability analysis of transverse motions of a cantilever microbeam sandwiched by two piezoelectric layers located on the lower and upper surfaces of the microbeam. Application of same DC and AC voltages to the upper and lower piezoelectric layers creates an axial force with steady and time-varying components. The eigenfunction expansion of the transverse motion equation leads to the creation of a Mathieu type parametric equation which is mostly seen in the stability analysis of the structures in the literature; using Floquet theory for single degree of freedom systems the stable and unstable regions of the problem are investigated. The effect of viscous damping and DC voltage on the stability region of the problem is also studied. The results show the stabilizing effect of the viscous damping and positive DC voltage on the behavior of the microbeam. The achieved results are finally compared with those reported in the literature.     

Study on Steady Shear,Morphology and Mechanical Behavior of Nanocomposites based on Polyamide 6

Nanocomposites of two different grades of polyamide 6 (PA6) with organically modified nanoclay were prepared via melt compounding in a twin‐screw extruder. The rheological behavior, morphology and mechanical properties of the nanocomposites were studied using a capillary rheometer, x‐ray diffraction (XRD), tapping‐mode atomic force microscopy (AFM), and tensile and flexural tests. XRD patterns indicate that the organically modified layered silicate was well dispersed in the PA6 matrix. From the AFM images the surface roughness of PA6 slightly increases with addition of organoclay. The rheological studies showed that the prepared nanocomposites have shear thinning behavior, obeying the power law equation. Addition of organoclay increases the shear stress and shear viscosity. At high rate of shear deformation the viscosity of nanocomposites are comparable to those of the pure polyamides. The activation energy of flow decreases with increasing nanoclay content. For most of the prepared nanocomposites the activation energy values increase with increasing shear rate. The tensile strength and flexural modulus and strength of the nanocomposites increase with increase of nanoclay content, but the extension at yield decreases with increasing clay loading.     

A new mathematical model towards the integration of cell formation with operator assignment and inter-cell layout problems in a dynamic environment

This paper proposes a new mathematical model to solve the cell formation, operator assignment and inter-cell layout problems, simultaneously. The objectives of proposed model are minimization of inter–intra cell part trips, machine relocation cost and operator related issues. Since the objective function of the proposed model consists of none commensurable statements, the preferred solution is obtained by the LP-metric approach. In order to validate the proposed model, some numerical examples are generated randomly and solved by branch and bound technique. Moreover; a real case study is illustrated in order to verify its applicability in an automobile producer company. Moreover the sensitivity analysis of proposed model shows that considering the operator assignment problem has significant impact on the overall system efficiency.     

Improved photoelectrochemical hydrogen production over decorated titania with copper and nickel oxides by optimizing the photoanode and reaction characteristics

We optimized photocatalytic hydrogen production over TiO₂-based photocatalyst by varying the dopant (nickel and copper oxide), thin film active area, nature and concentration of sacrificial agents, and light intensity in a photoelectrochemical (PEC) cell/dye-sensitized solar cell (DSSC). Various characterization techniques have been used to investigate the structural, morphological, optical, and PEC behavior of single and codoped TiO₂. The TiO₂ decorated with both Cu and Ni oxides with active area of 1 cm² in a mixture of 5 vol % glycerol and 1 M KOH under light intensity of 100 mWcm^?2 produced the maximum hydrogen of 338.4 μmol cm^?2 for 2 h. The superior photocatalyst performance of this photocatalyst is attributed to its small crystallite size and large pore size, as confirmed by X-ray diffractometer, Transmission electron microscopy (TEM), and surface area of Brunauer-Emmet-Teller (S_BET). The absorption edges of this photocatalyst had the highest red shift compared with single doped and pure TiO₂ because of more indirect transitions of the photoexcited electrons, greater charge carrier separation, and lower recombination rate. The photoanode active area of 1 cm² with better photocatalytic performance correlated with the number of defects and grain boundaries. Glycerol shifted the conduction band of the photocatalyst to more negative flat potential compared with others. Increasing the concentration of glycerol further than 5 vol% saturated the photocatalyst active sites, increased photooxidation intermediates of glycerol, and reduced the hydrogen production. The light intensity had the maximum impact on the hydrogen production and could strongly control the number of charge carriers in both the PEC cell and the DSSC.     

Kinetic study of hydrogen sulfide decomposition on Pt(111) surface

In this work, kinetic of H₂S conversion to H₂ molecule on the surface of Pt(111) is studied using kinetic Monte Carlo simulation. The results of simulation were fitted to the experimental temperature-programed desorption spectra. The good agreement between the empirical and the simulated data confirms the proposed mechanism and kinetic data (activated energies and pre-exponential factors). The influence of variables such as temperature and concentrations of H₂S and H₂ on the overall results of hydrogen production is studied. The condition is proposed in which the best yield of reaction at minimum temperature is obtained. Results show that platinum is a perfect catalyst for converting H₂S to H₂ and it has a perfect performance (98%) after 5 μs at low temperature of 227°C.     

Adsorption kinetics at the solid/solution interface: statistical rate theory at initial times of adsorption and close to equilibrium

The kinetics of solute adsorption at the solid/solution interface has been studied by statistical rate theory (SRT) at two limiting conditions, one at initial times of adsorption and the other close to equilibrium. A new kinetic equation has been derived for initial times of adsorption on the basis of SRT. For the first time a theoretical interpretation based on SRT has been provided for the modified pseudo-first-order (MPFO) kinetic equation which was proposed empirically by Yang and Al-Duri. It has been shown that the MPFO kinetic equation can be derived from the SRT equation when the system is close to equilibrium. On the basis of numerically generated points ( t, q) by the SRT equation, it has been shown that we can apply the new equation for initial times of adsorption in a larger time range in comparison to the previous q vs radical t linear equation. Also by numerical analysis of the generated kinetic data points, it is shown that application of the MPFO equation for modeling of whole kinetic data causes a large error for the data at initial times of adsorption. The results of numerical analysis are in perfect agreement with our theoretical derivation of the MPFO kinetic equation from the SRT equation. Finally, the results of the present theoretical study were confirmed by analysis of an experimental system.     

Generation of Haploid Spermatids on Silk Fibroin-Alginate-Laminin-Based Porous 3D Scaffolds

In vitro production of sperm is a desirable idea for fertility preservation in azoospermic men and prepubertal boys suffering from cancer. In this study, a biocompatible porous scaffold based on a triad mixture of silk fibroin (SF), alginate (Alg), and laminin (LM) is developed to facilitate the differentiation of mouse spermatogonia stem cells (SSCs). Following SF extraction, the content is analyzed by SDS-PAGE and stable porous 3D scaffolds are successfully prepared by merely Alg, SF, and a combination of Alg-SF, or Alg-SF-LM through freeze-drying. Then, the biomimetic scaffolds are characterized regarding the structural and biological properties, water absorption capacity, biocompatibility, biodegradability, and mechanical behavior. Neonatal mice testicular cells are seeded on three-dimensional scaffolds and their differentiation efficiency is evaluated using real-time PCR, flow cytometry, immunohistochemistry. Blend matrices showed uniform porous microstructures with interconnected networks, which maintained long-term stability and mechanical properties better than homogenous structures. Molecular analysis of the cells after 21 days of culture showed that the expression of differentiation-related proteins in cells that are developed in composite scaffolds is significantly higher than in other groups. The application of a composite system can lead to the differentiation of SSCs, paving the way for a novel infertility treatment landscape in the future.