Structure and properties of the mesophase of syndiotactic polystyrene. II. Effect of stepwise extraction on the preparation of the mesophase

In this study, a novel stepwise extraction method has been examined. The guest molecules housed between the helices of the clathrate δ form of syndiotactic polystyrene can be removed completely with this method. A systematic study of the preparation of a solvent‐free mesophase (emptied clathrate) membrane, its helical and residual solvent contents, and its structural transformations has been performed. In this first attempt, an enhancement in the TTGG helical content has been observed in the extracted membrane, and a conceptual mechanism is proposed. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 269–273, 2003     

Structure and properties of the mesophase of syndiotactic polystyrene. VIII. Solvent sorption behavior of syndiotactic polystyrene/p‐chlorotoluene mesophase membranes

A crystalline δ form of a syndiotactic polystyrene (sPS) membrane was prepared from a solution of sPS (1 wt %) and p‐chlorotoluene (p‐CT) by a solution‐casting method. The mesophase (δ empty form) of sPS was obtained by the extraction of the guest solvent from the δ form of sPS by a stepwise solvent‐extraction method. The sPS/p‐CT mesophase membrane [p‐CT (A‐M)] was used for the sorption of 1 mol % p‐CT for different times and for the sorption of different concentrations of p‐CT, chlorobenzene (CB), p‐xylene (p‐X), toluene, and chloroform for 48 h. The presence of solvents in the sPS membrane was confirmed by IR analysis. A thermal study revealed that the sorption amount of 1 mol % p‐CT increased with increasing immersion time, and the sorption amounts of different solvents increased with increasing solvent concentration. Differential scanning calorimetry results showed that the desorption peak temperature increased as the amount of the solvent increased in the clathrated sPS membrane. Wide‐angle X‐ray diffraction results showed that 2θ at 8.25° was slightly shifted toward 8°, and there was no change in the peak position at 10° for p‐CT (A‐M), which was immersed in different solvents (1 mol %); however, the intensity of 2θ at 10° was not similar for all the samples. Among the solvents used for the sorption studies at 1 mol %, p‐CT (A‐M) could sorb more p‐CT and CB than p‐X, toluene, and chloroform. The solvent sorption isotherm was the Langmuir sorption mechanism. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3439–3446, 2004     

Laser writing techniques for photomask fabrication using a femtosecond laser

Photomasks are the backbone of microfabrication industries. Currently they are fabricated by a lithographic process, which is very expensive and time consuming since it is a multi-step process. These issues can be addressed by fabricating photomasks by direct femtosecond laser writing, which is a single-step process and comparatively cheaper and faster than lithography. In this paper we discuss our investigations on the effect of two types of laser writing techniques, namely front- and rear-side laser writing, with regard to the feature size and the edge quality of a feature. It is proved conclusively that for the patterning of masks, front-side laser writing is a better technique than rear-side laser writing with regard to smaller feature size and better edge quality. Moreover the energy required for front-side laser writing is considerably lower than that for rear-side laser writing. Received: 22 May 2001 / Accepted: 14 September 2001 / Published online: 17 October 2001     

Characterization of surface deformation around Vickers indentations in InGaAsP epilayers on InP substrate

The deformation surrounding Vickers indentations on InGaAsP/InP epilayers have been studied in detail. The surface topography was characterized by using atomic force microscopy (AFM). The material pile-up and sink-in regions around the indentation impression was observed for the quaternary InGaAsP/InP epilayers. The sectional analysis mode of the AFM shows the depth profile at the indented region. Microindentation studies were carried out for different atomic fraction of the quaternary InGaAsP/InP compound semiconductor alloys. The microhardness values of InGaAsP/InP epilayers were found to be in the range of 5.08 and 5.73 GPa. These results show that the hardness value of the quaternary alloy drastically increases as the composition of As was increased by 0.01 atomic fraction and when the phosphorous concentration decreases from 0.4 to 0.38. The reason may be that the increase in As concentration hardens the lattice when phosphorous concentration was less and hardness decreases when phosphorous was increased.     

Critical phenomena in FINEMET alloy

The Fe_73.5Cu₁Nb₃Si_13.5B₉ FINEMET alloy has been prepared by the rapid solidification technique. The critical behaviour of this alloy in the amorphous as well as in its nanocrystalline states has been studied near their respective Curie temperatures. From the values of the critical exponents one can conclude that the alloy behaves like a 3D Heisenberg ferromagnet in the amorphous and nanocrystalline states. But there exists a slight increase in the value of β for the alloy annealed at 823 K (the nanocrystalline state) as observed in most of the amorphous alloys.     

Precise lattice parameter measurements in CsCl-Br solid solutions between room temperature and 90°K by powder x-ray diffraction

Solid solutions of CsCl-Br in five different concentrations were prepared in sealed quartz tubes by heating the mixture to 1123°K for 6–8 hr and quenching to room temperature. X-ray diffractograms were taken at eight different temperatures between room temperature and 90°K for these solid solutions using the YPC50NM powder diffractometer and a continuous flow cryostat. The observed lattice parameters for each sample at each temperature obtained from the powder diffractograms were then extrapolated to give the true lattice parameters using the least square method with Nelson-Riley extrapolation scheme. The values of the true lattice parameters at each concentration and at each temperature were tabulated and the results discussed. It is shown that the lattice parameters vs temperature for some concentrations exhibit an anomalous behaviour. Contribution No. 691     

Novel simulated moving-bed adsorber for the fractionation of gas mixtures

The separation of propylene-propane mixture is an energy intensive operation commercially practiced using cryogenic distillation. The separation by pressure swing adsorption has been studied as an alternative. A fixed-bed pressure swing adsorption yields the heavy component as a pure product. The product recovery and the productivity are not high. In a moving-bed process, because of the counter-current solid-gas contact, the separation achieved is similar to that of the fractionation by distillation. Although the moving-bed operation offers the upper limit for the performance of a cyclic adsorptive process, due to mechanical complexities in the handling of solids the 'simulated' moving-bed is preferred. By moving the inlet and outlet ports of streams located along the length of the bed, a moving-bed process can be realized in a fixed bed. We describe here a 'moving-port' system which permits injection or withdrawal of the fluid along the axial direction in a fixed bed. A fixed bed embedded with the moving-port systems emulates a simulated moving-bed adsorber. The proposed adsorber can fractionate a binary gas mixture into two product streams with high purities. It is similar to the Sorbex process of UOP but does not have the eluent as an additional separating agent. A parametric study indicates that high purity products and a higher productivity by an order of magnitude can be achieved with simulated moving-beds compared to the fixed beds.