Nanostructured Colloidal Solutions of Malachite Green Formulated: Nonlinear Optical Properties and Simulation

Journal of Fluorescence - Malachite green (MG) is a dye that has been presented to use as photosensitizers for photodynamic therapy (PDT). Nonlinear absorption coefficient (β) and nonlinear...     

Filter-radiometer-based realization of candela and establishment of photometric scale at UME

The luminous intensity unit of candela was realized based on filter-radiometer, which is traceable to detector-based primary standard electrical substitution cryogenic radiometer (ESCR). In that realization the traditional Osram Wi41/G-type incandescent lamp and filter-radiometer consisting of an aperture, a V(λ) filter and a silicon photodiode based trap detector were used as light source and detection element, respectively. Measurement techniques of effective aperture area, spectral transmittance of V(λ) filter and absolute responsivity of trap detector are also presented.     

Renewable sol-gel carbon ceramic electrodes modified with a Ru-complex for the amperometric detection of l-cysteine and glutathione

A renewable three-dimensional chemically modified carbon ceramic electrode containing Ru [(tpy)(bpy)Cl] PF₆ was constructed by sol-gel technique. It exhibits an excellent electro-catalytic activity for oxidation of l-cysteine and glutathione at pH range 2-8. Cyclic voltammetry was employed to characterize the electrochemical behavior of the chemically modified electrode. The electrocatalytic behavior is further exploited as a sensitive detection scheme for l-cysteine and glutathione by hydrodynamic amperometry. Optimum pH value for detection is 2 for both l-cysteine and glutathione. The catalytic rate constants for l-cysteine and glutathione were determined, which were about 2.1×10³ and 2.5×10³ M⁻¹ s⁻¹, respectively. Under the optimized condition the calibration curves are linear in the concentration range 5-685 and 5-700 μM for l-cysteine and glutathione determination, respectively. The detection limit (S/N=3) and sensitivity is 1 μM, 5 nA/μM for l-cysteine and 1 μM, 7.8 nA/μM for glutathione. The relative standard deviation (RSD) for the amperogram's currents with five injections of l-cysteine or glutathione at concentration range of linear calibration is <1.5%. The advantages of this amperometric detector are: high sensitivity, good catalytic effect, short response time (t<3 s), remarkable long-term stability, simplicity of preparation and reproducibility of surface fouling (RSD for six successive polishing is 3.31%). This sensor can be used as a chromatographic detector for analysis of l-cysteine and glutathione.     

The facile and efficient Michael addition of indoles and pyrrole to alpha,beta-unsaturated electron-deficient compounds catalyzed by aluminium dodecyl sulfate trihydrate [Al(DS)3].3H2O in water

Aluminium dodecyl sulfate trihydrate [Al(DS)3].3H2O is easily prepared and can be used as a Lewis acid surfactant catalyst in water to conduct the highly efficient Michael addition of indoles and pyrrole to alpha,beta-unsaturated electron-deficient compounds at room temperature.     

Synthesis of 11C-amides using [11C]carbon monoxide and in situ activated amines by palladium-mediated carboxaminations

[11C]Carbon monoxide at low concentrations, aryl halides and amines were used in the palladium-mediated synthesis of twenty 11C-amides. In the study several approaches to improve the radiochemical yield were explored. Eight of the selected amides were prepared by in situ activation of the amines using lithium bis(trimethylsilyl)amide and the radiochemical yields of these reactions were improved compared to utilising a previous reported method. In the synthesis of 1-[carbonyl-11C]benzoyl-3-methyl-1H-indole (11) from 3-methyl-1H-indole (25), the corresponding organotin-amine was prepared prior to the acylation reaction. In a typical experiment, N-(4-hydroxyphenyl)[carbonyl-11C]acetamide (5) was prepared in 15% radiochemical yield using 4-aminophenol (20) but the yield increased to 63% when the amine was activated by lithium bis(trimethylsilyl)amide.     

Sonoelectroanalysis: investigation of bismuth-film-modified glassy carbon electrodes

Bismuth-modified glassy carbon electrodes have been investigated for their suitability in sonoelectroanalysis. The stability of the bismuth film to the application of ultrasound was assessed via voltammetric and atomic force microscopy (AFM) studies which revealed little ablation at powers up to an intensity of 130 W cm^–2 delivered from a 25-kHz sonic horn. Furthermore, bismuth-film-modified glassy carbon electrodes were evaluated for the sonoelectroanalytical quantification of zinc and cadmium. Detection limits of 2×10^–7 M and 6×10^–9 M respectively were found after a 60-s deposition time via an acoustically assisted deposition protocol.     

Renewable-surface sol-gel derived carbon ceramic electrode fabricated by [Ru(bpy)(tpy)Cl]PF6 and its application as an amperometric sensor for sulfide and sulfur oxoanions

A highly sensitive and fast responding sensor for the determination of thiosulfate, sulfite, sulfide and dithionite is described. It consists of a chemically modified carbon ceramic composite electrode (CCE) containing [Ru(bpy)(tpy)Cl]PF6 complex that was constructed by the sol-gel technique. A reversible redox couple of Ru(II)/Ru(III) was observed as a solute in acetonitrile solution and as a component of carbon based conducting composite electrode. Electrochemical behavior and stability of modified CCE were investigated by cyclic voltametry, the apparent electron transfer rate constant (kappa(S)) and transfer coefficient (a) were determined by cyclic voltametry which were about 28 s(-1) and 0.43 respectively. Electrocatalytic oxidation of S(2-), SO3(2-), S2O4(2-) and S2O3(2-) were effective at the modified electrode at significantly reduced overpotentials and in the pH range 1-11. Optimum pH values for amperometric detection of thiosulfate, dithionite, sulfide and sulfite are 7, 9, 2 and 2. Under the optimized conditions the calibration curves are linear in the concentration ranges 1-500, 3-80, 2-90 and 1-100 microM for S2O3(2-), SO3(2-), S2- and S2O4(2-) determination. The detection limit (signal to noise is 3) and sensitivity are 0.5 and 12, 2.8 and 6, 1.6 and 8, and 0.65 microM and 80 nA microM(-1) for thiosulfate, sulfite, sulfide and dithionite detection. The modified carbon ceramic electrode doped with Ru-complex shows good reproducibility, a short response time (t < 2 s), remarkable long term stability (> 6 month) and especially good surface renewability by simple mechanical polishing (RSD for eight successive polishing is 2%). The advantages of this sulfur compound amperometric detector based on ruthenium doped CCE are high sensitivity, inherent stability at a broader pH range, excellent catalytic activity, less expense and simplicity of preparation in comparison with recently published papers. This sensor can be used as a chromatographic detector for analysis of sulfur derivatives.     

Modification of carbon ceramic electrode prepared with sol-gel technique by a thin film of chlorogenic acid: application to amperometric detection of NADH

The carbon ceramic electrode prepared with sol-gel technique is modified by a thin film of chlorogenic acid (CGA). By immersing the carbon ceramic electrode in aqueous solution of chlorogenic acid at less than 2 s a thin film of chlorogenic acid adsorbed strongly and irreversibly on the surface of electrode. The cyclic voltammetry of the resulting modified CCE prepared at optimum conditions shows a well-defined stable reversible redox couple due to hydroquinone/quinone system in both acidic and basic solutions. The modified electrode showed excellent electrocatalytic activity toward NADH oxidation and it also showed a high analytical performance for amperometric detection of NADH. The catalytic rate constant of the modified carbon ceramic electrode for the oxidation of NADH is determined by cyclic voltammetry measurement. Under the optimised conditions the calibration curve is linear in the concentration range 1-120 μm. The detection limit (S/N = 3) and sensitivity are 0.2 μM and 25 nA μM⁻¹.The results of six successive measurement-regeneration cycles show relative standard deviations of 2.5% for electrolyte solution containing 1 mM NADH, indicating that the electrode renewal gives a good reproducible and antifouling surface. The advantages of this amperometric detector are: high sensitivity, excellent catalytic activity, short response time t < 2 s, remarkable long-term stability, simplicity of preparation at short time and good reproducibility.     

Electrocatalytic Reduction of H2O2 and Oxygen on the Surface of Thionin Incorporated onto MWCNTs Modified Glassy Carbon Electrode: Application to Glucose Detection

A new H₂O₂ enzymeless sensor has been fabricated by incorporation of thionin onto multiwall carbon nanotubes (MWCNTs) modified glassy carbon electrode. First 50 μL of acetone solution containing dispersed MWCNTs was pipetted onto the surface of GC electrode, then, after solvent evaporations, the MWCNTs modified GC electrode was immersed into an aqueous solution of thionin (electroless deposition) for a short period of time <5–50 s. The adsorbed thin film of thionin was found to facilitate the reduction of hydrogen peroxide in the absence of peroxidase enzyme. Also the modified electrode shows excellent catalytic activity for oxygen reduction at reduced overpotential. The rotating modified electrode shows excellent analytical performance for amperometric determination of hydrogen peroxide, at reduced overpotentials. Typical calibration at ?0.3 V vs. reference electrode, Ag/AgCl/3 M KCl, shows a detection limit of 0.38 μM, a sensitivity of 11.5 nA/μM and a liner range from 20 μM to 3.0 mM of hydrogen peroxide. The glucose biosensor was fabricated by covering a thin film of sol–gel composite containing glucose oxides on the surface of thionin/MWCNTs modified GC electrode. The biosensor can be used successfully for selective detection of glucose based on the decreasing of cathodic peak current of oxygen. The detection limit, sensitivity and liner calibration rang were 1 μM, 18.3 μA/mM and 10 μM–6.0 mM, respectively. In addition biosensor can reach 90% of steady currents in about 3.0 s and interference effect of the electroactive existing species (ascorbic acid–uric acid and acetaminophen) is eliminated. The usefulness of biosensor for direct glucose quantification in human blood serum matrix is also discussed. This sensor can be used as an amperometric detector for monitoring oxidase based biosensors.     

Effects of strain on shot noise properties in graphene superlattices

In this paper the transmission and the shot noise properties through the strain-inducedgraphene superlattices are studied. It is found that for the zigzag direction strain theFano factor shows a peak at new Dirac-like point and the position of the new Dirac pointvaries against the strain. Also, Fano factor has an oscillatory behavior with respect tostrain strength and the oscillation period decreases by increasing the number of barriers.However, for the armchair direction strain the transmission can be blocked by the electricbarrier and the Fano factor approaches 1, this is different from the zigzag directionstrain.