Self-bonding in an amorphous polymer below the glass transition: A T-peel test investigation

Films of amorphous polystyrene (PS) with a weight-average molecular weight (M_w) of 225 × 10³ g/mol were bonded in a T-peel test geometry, and the fracture energy (G) of a PS/PS interface was measured at the ambient temperature as a function of the healing time (t_h) and healing temperature (T_h). G was found to develop with (t_h)^1/2 at T_h = T_g-bulk − 33 °C (where T_g-bulk is the glass-transition temperature of the bulk sample), and log G was found to develop with 1/T_h at T_g-bulk − 43 °C ≤ T_h ≤ T_g-bulk − 23 °C. The smallest measured value of G = 1.4 J/m² was at least one order of magnitude larger than the work of adhesion required to reversibly separate the PS surfaces. These three observations indicated that the development of G at the PS/PS interface in the temperature range investigated (<T_g-bulk) was controlled by the diffusion of chain segments feasible above the glass-transition temperature of the interfacial layer, in agreement with our previous findings for fracture stress development at several polymer/polymer interfaces well below T_g-bulk. Close values of G = 8–9 J/m² were measured for the symmetric interfaces of polydisperse PS [M_w = 225 × 10³, weight-average molecular weight/number-average molecular weight (M_w/M_n) = 3] and monodisperse PS (M_w = 200 × 10³, M_w/M_n = 1.04) after healing at T_h = T_g-bulk − 33 °C for 24 h. This implies that the self-bonding of high-molecular-weight PS at such relatively low temperatures is not governed by polydispersity. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1861–1867, 2004     

Rheological and physical properties of aliphatic hyperbranched polyesters

The effects of the size (pseudo‐generation number) and nature of end groups on physical and rheological properties were investigated for a series of hyperbranched polyesters based on an ethoxylated pentaerythritol core and 2,2‐bis‐(hydroxymethyl)propionic acid repeat units. The observed linear dependence of the melt viscosity on the molar mass in the high pseudo‐generation‐number limit indicated that entanglement effects were substantially absent. Moreover, the marked influence of end capping of the end groups on the physical and rheological properties suggested that intermolecular interactions were dominated by contacts between the outer shells of the molecules, in which the end groups were assumed to be concentrated. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1218–1225, 2004     

On the optimum set of polarization measurements for the scattering of two indentical fermions to determine the helicity amplitudes

The polarization asymmetries related to usual polarizations combine at least 4 different helicity amplitudes. The introduction of ±45° inclined transverse polarizations allows us to obtain the complete set of new polarization asymmetries combining only up to 3 helicity amplitudes. There are no further polarization asymmetries depending on a smaller number of helicity amplitudes. These expressions are most economical to determine the helicity amplitudes from observed data. Some of them are suitable to study especially the spin-flip effects. We give a complete Table of all such polarization asymmetries.     

Vanishing of local homology

 We study the vanishing properties of local homology of complexes of modules without assuming that its homology is artinian. Using vanishing results for local homology and cohomology we prove new vanishing results for Ext- and Tor-modules. Received: 1 August 2002; in final form: 23 September 2002 / Published online: 16 May 2003 Mathematics Subject Classification (1991): 13C12, 13D07, 13D45.     

Capabilities and limits of ICP-MS for direct determination of element traces in saline solutions

An ICP-MS method for the determination of ultra-traces of 24 Elements (Li, Be, Mg, Al, Cr, Mn, Co, Zn, Cu, Ga, As, Se, Rb, Sr, Mo, Ag, Cd, Sn, Sb, Ba, Tl, Pb, Bi, U) at ng/L to μg/L levels in highly saline solutions (up to 30 g/L NaCl) was developed. Calculated to the salt content of the samples, limits of detection at the sub-μg/kg level were obtained. This allows the measurement of samples like sea water, or clinical samples like urine, serum and whole blood, with few or without sample preparation and a drastic improvement to the limits of detection. Compared to the determination in solutions of 1 g/L NaCl the limits of detection in the original sample were improved by one order of magnitude. Improvements in instrumental stability are achieved by the use of an additional gas, that is introduced to the aerosol stream and avoids salt deposition in the aerosol tube of the torch, the use of High Matrix Content (HMC) cones, that show no clogging even at NaCl-concentrations up to 50 g/L. With this setup the long term stability for measurements with changing matrix concentrations is < 10% without and < 5% with use of an internal standard for the individual samples. Cleaning up is necessary after 2 days of operation. The direct analysis of the Nearshore Seawater Reference Material NRC-CNRC CASS3 showed a good agreement with the certified and measured concentrations. Elements, that do not suffer from an isobaric overlap of matrix compounds can be determined clearly at ng/L levels. Measurement of different matrix concentrations showed, that acceptable results can be achieved with a single calibration for concentrations from 5 g/L NaCl to 30 g/L NaCl, though matrix matching shows the best results.     

Multicriteria Semi-Obnoxious Network Location Problems (MSNLP) with Sum and Center Objectives

Locating a facility is often modeled as either the maxisum or the minisum problem, reflecting whether the facility is undesirable (obnoxious) or desirable. But many facilities are both desirable and undesirable at the same time, e.g., an airport. This can be modeled as a multicriteria network location problem, where some of the sum-objectives are maximized (push effect) and some of the sum-objectives are minimized (pull effect).We present a polynomial time algorithm for this model along with some basic theoretical results, and generalize the results also to incorporate maximin and minimax objectives. In fact, the method works for any piecewise linear objective functions. Finally, we present some computational results.     

Monitoring photopolymerization reactions with optical pyrometry

This article describes the development of optical pyrometry (OP) as a new analytical technique for the continuous monitoring of the progress of both free‐radical and cationic photopolymerizations. The method is rapid, reproducible, and very easy to implement. A temperature profile of a photopolymerization can be obtained. Preliminary studies have shown that the temperatures of some polymerizing monomers can easily reach temperatures in excess of 250 °C. The effects of the mass and reactivity of the monomer, light intensity, structures, and concentrations of the photoinitiators and monomers as well as the presence or absence of oxygen on various free‐radical and cationic photopolymerizations were examined with this method. Coupling of real‐time infrared spectroscopy with OP provides a convenient method for simultaneously monitoring both the chemical conversion and the temperature of a photopolymerization. This combined technique affords new insights into the effects of temperature‐induced autoacceleration on the course of photopolymerizations. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 579–596, 2003     

Dependence of impurity incorporation upon substrate misorientation during GaAs growth by metalorganic vapour phase epitaxy

Doping studies of the incorporation behaviour of three different dopants (Zn, In and Si) versus the misorientation of the (100) surface during MOVPE growth of GaAs have been carried out with diethylzinc, trimethylindium and disilane as precursors. The incorporation of the dopants has been studied as function of the input mole fraction dopant, growth temperature, degree and direction of misorientation. In order to explain the results we discuss the BCF theory and the nature of the steps as function of above mentioned parameters. It appears that the BCF theory alone cannot explain the results, a counteracting mechanism has been introduced based on preferential arsenic desorption from the step edges.