Gas chromatographic-mass spectrometric method for polycyclic aromatic hydrocarbon analysis in plant biota

Using gas chromatography-mass spectrometry, a new method was developed for the identification and the quantification of polycyclic aromatic hydrocarbons (PAHs) in plants. This method was particularly optimised for PAH analyses in marine plants such as the halophytic species, Salicornia fragilis Ball et Tutin. The saponification of samples and their clean up by Florisil solid-phase extraction succeeded in eliminating pigments and natural compounds, which may interfere with GC-MS analysis. Moreover, a good recovery of the PAHs studied was obtained with percentages ranging from 88 to 116%. Application to the determination of PAH in a wide range of coastal halophytic plants is presented and validated the efficiency, the accuracy and the reproducibility of this method.     

Thermosensitive copolymer coatings with enhanced wettability switching

Expanded cross-linked copolymers of poly(N-isopropylacrylamide) (PNiPAAm) and poly(acrylic acid) (PAAc) of varying monomer ratios were grafted from a crystalline silicon surface. Surface-tethered polymerization was performed at a slightly basic pH, where electrostatic repulsion among acrylic acid monomer units forces the network into an expanded polymer conformation. The influence of this expanded conformation on switchability between a hydrophilic and a hydrophobic state was investigated. Characterization of the copolymer coating was carried out by means of X-ray photoelectron spectroscopy (XPS) ellipsometry, and diffuse reflectance IR. Lower critical solution temperatures (LCSTs) of the copolymer grafts on the silicon surfaces were determined by spectrophotometry. Temperature-induced wettability changes were studied using sessile drop contact angle measurements. The surface topography was investigated by atomic force microscopy (AFM) in Milli-Q water at 25 and 40 degrees C. The reversible attachment of a fluorescently labeled model protein was studied as a function of temperature using a fluorescence microscope and a fluorescence spectrometer. Maximum switching in terms of the contact angle change around the LCST was observed at a ratio of 36:1 PNiPAAm to PAAc. The enhanced control of biointerfaces achieved by these coatings may find applications in biomaterials, biochips, drug delivery, and microfluidics.     

Metalization of polymer beads via polymer‐supported hydrazines as reducing agents

A new method for depositing metal onto a polymer surface has been developed in which the metal coating of polymer beads is performed with hydrazine functions as reducing agents on the surface of the polymer itself. In this study, glycidyl methacrylate–methyl methacrylate–divinyl benzene terpolymer was prepared as spherical beads with a suspension polymerization methodology. Beads of the polymer sample (210–420‐μm fraction) containing 3.4 mmol g^?1 epoxy were treated with an excess of hydrazinium hydroxide to yield a polymer with 2.3 mmol g^?1 hydrazine functions. The hydrazine functions on the polymer surfaces were efficient in metal reductions. Therefore, the modified bead polymer samples, when soaked in aqueous ammonia solutions of Ni(II), Ag(I), and Cu(II) ions (0.1 M), were covered rapidly by the corresponding zero‐valent metal ions. Metal deposition took place almost quantitatively (ca. 4.5 mmol/g of the polymer) within 60 min of the contact times. The accumulations of metal were followed visually and occurred only on the polymer beads. There was no evidence that the reaction occurred within the solution. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 748–754, 2002; DOI 10.1002/pola.10158     

Discrimination of allied species within the genus Turbinaria (Fucales, Phaeophyceae) using HRMAS NMR spectroscopy

A novel chemotaxonomical method based on 1D (1)H HRMAS NMR spectroscopy is being tested for taxonomical purposes. This powerful technique allowed us to discriminate between specimens belonging to two sister species of Turbinaria, which are difficult to tell apart using only morphological characters. Based on spectra analysis, the results allowed us to successfully group the specimens according to their species. Thus, the efficiency of HRMAS NMR spectroscopy for the discrimination of algal species and for the pre-screening of potential chemomarkers is demonstrated.     

ToF‐SIMS characterisation of methane‐ and hydrogen‐plasma‐modified graphite using principal component analysis

Time of flight secondary ion mass spectrometry (ToF‐SIMS) has been used to determine the extent of surface modification of highly ordered pyrolytic graphite (HOPG) samples that were exposed to radio‐frequency methane and hydrogen plasmas. The ToF‐SIMS measurements were examined with the multivariate method of principal component analysis (PCA), to maximise the amount of spectral information retained in the analysis. This revealed that the plasma (methane or hydrogen plasma) modified HOPG exhibited greater hydrogen content than the pristine HOPG. The hydrogen content trends observed from the ToF‐SIMS studies were also observed in elastic recoil detection analysis measurements. The application of the ToF‐SIMS PCA method also showed that small hydrocarbon fragments were sputtered from the hydrogen‐plasma‐treated sample, characteristic of the formation of a plasma‐damaged surface, whereas the methane‐plasma‐treated surface sputtered larger hydrocarbon fragments, which implies the growth of a polymer‐like coating. Scanning tunnelling microscopy measurements of the modified surfaces showed surface features that are attributable to either etching or film growth after exposure to the hydrogen or methane plasma. Copyright © 2009 John Wiley & Sons, Ltd.     

High‐speed tomography under extreme conditions at the PSICHE beamline of the SOLEIL Synchrotron

In situ microtomography at high pressure and temperature has developed rapidly in the last decade, driven by the development of new high‐pressure apparatus. It is now routinely possible to characterize material under high pressure with acquisition times for tomograms of the order of tens of minutes. Here, advantage was taken of the possibility to combine the use of a pink beam projected through a standard Paris–Edinburgh press in order to demonstrate the possibility to perform high‐speed synchrotron X‐ray tomography at high pressure and temperature allowing complete high‐resolution tomograms to be acquired in about 10 s. This gives direct visualization to rapidly evolving or unstable systems, such as flowing liquids or reacting components, and avoids assumptions in the interpretation of quenched samples. Using algebraic reconstruction techniques allows the missing angle artefacts that result from the columns of the press to be minimized.     

The Surface Modification of Pure Cellulose Paper Induced by Low-Pressure Nitrogen Plasma Treatment

We have used Time of Flight Secondary Ion Mass Spectroscopy (TOF-SIMS) in combination with X-ray photoelectron spectroscopy (XPS) to study chemical changes taking place at the surface of pure cellulose paper samples treated in N₂ plasma for periods of time up to 60 seconds. High resolution TOF-SIMS spectra permit the detection of various functionalities containing nitrogen, even following very brief (2s) plasma exposure. Correlations between chemistry and surface properties, such as water wettability, are presented and discussed.     

Hydrogenation of sp-bonded carbon surfaces using methane plasma

Highly ordered pyrolytic graphite was exposed to radio-frequency methane plasma to produce a hydrogen-terminated carbon surface. The effects of treatment parameters, namely exposure time, applied power and methane pressure, upon the treated surfaces’ chemical and morphological properties were systematically investigated. Scanning tunnelling microscopy measurements showed growth features on the plasma treated surface, the coverage of which was shown to increase with plasma exposure time or applied plasma power and decrease with gas pressure. Analyses of post-treated surface structures (via static secondary ion mass spectrometry with the aid of principle component analysis) showed an increase in surface hydrogen with plasma exposure time, applied plasma power and decreasing gas pressure. The results of these analyses were further supported by elastic recoil detection analysis measurements, which showed similar trends for the experimental parameters on the resultant surface hydrogen content.