Modelling and design of a travelling-wave electro-optic modulator on InP

Based on a rigorous vectorial analysis, a fast travelling-wave Mach–Zehnder modulator is modelled and designed. The cross-section of the semiconductor layer stack and the lossy electrodes are carefully modelled using the method of lines in order to investigate propagation characteristics, velocity and losses. This yields an accurate microwave and optical field distribution to explain the behaviour of the component. In order to enhance the modulation efficiency, design curves are derived and the cross-sectional dimensions for minimum microwave loss are determined. The loss of the optimized modulator agrees very well with small-signal measurements up to 40 GHz and HFSS simulations. The layerstack of the fabricated device is suitable for integration with InP multi-wavelength lasers.     

Metallo‐supramolecular block copolymer micelles: Improved preparation and characterization

Micelles prepared from amphiphilic block copolymers in which a poly(styrene) segment is connected to a poly(ethylene oxide) block via a bis‐(2,2′:6′,2″‐terpyridine‐ruthenium) complex have been intensely studied. In most cases, the micelle populations were found to be strongly heterogeneous in size because of massive micelle/micelle aggregation. In the study reported in this article we tried to improve the homogeneity of the micelle population. The variant preparation procedure developed, which is described here, was used to prepare two “protomer”‐type micelles: PS₂₀‐[Ru]‐PEO₇₀ and PS₂₀‐[Ru]‐PEO₃₇₅. The dropwise addition of water to a solution of the compounds in dimethylformamide was replaced by the controlled addition of water by a syringe pump. The resulting micelles were characterized by sedimentation velocity and sedimentation equilibrium analyses in an analytical ultracentrifuge and by transmission electron microscopy of negatively stained samples. Sedimentation analysis showed virtually unimodal size distributions, in contrast to the findings on micelles prepared previously. PS₂₀‐[Ru]‐PEO₇₀ micelles were found to have an average molar mass of 318,000 g/mol (corresponding to 53 protomers per micelle, which is distinctly less than after micelle preparation by the standard method) and an average hydrodynamic diameter (d_h) of 18 nm. For PS₂₀‐[Ru]‐PEO₃₇₅ micelles, the corresponding values were M = 603,000 g/mol (31 protomers per micelle) and d_h = 34 nm. The latter particles were found to be identical to the “equilibrium” micelles prepared in pure water. Both micelle types had a very narrow molar mass distribution but a much broader distribution of s values and thus of hydrodynamic diameters. This indicates a conformational heterogeneity that is stable on the time scale of sedimentation velocity analysis. The findings from electron microscopy were in disagreement with those from the sedimentation analysis both in average micelle diameter and in the width of the distributions, apparently because of imperfections in the staining procedure. The preparation procedure described also may be useful in micelle formation from other types of protomers. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4458–4465, 2004     

Nanostructured Ion-Selective MCM-48 Membranes

Templated MCM-48 silica was prepared using CTAB as surfactant. The MCM-48 powders and thin films were characterized by different techniques. MCM-48 layers were deposited on macroporous α-alumina supports and silicon nitride microsieves. The water permeability of MCM-48 was compared with the permeability of conventional mesoporous γ-alumina membranes. The applicability of MCM-48 as ion-selective electric field-driven switchable interconnect for microfluidic devices was demonstrated.     

Picosecond control of coherent magnetisation dynamics in permalloy thin films by picosecond magnetic field pulse shaping

We have measured the response of a 20×10 μm, 8 nm thin NiFe (80:20) permalloy film due to excitation by short in-plane magnetic field pulses. We will show that using a two-pulse-technique a complete control of the precessional motion of the magnetisation can be achieved on picosecond timescales. Furthermore, we will present numerical calculations which show that a complete suppression of magnetisation ringing after switching can only be realised by a cascade of short field pulses.     

Quantification problems in depth profiling of pwr steels using Ar+ ion sputtering and XPS analysis.

The oxide scales of AISI 304 formed in boric acid solutions at 300 degrees C and pH = 4.5 have been studied using X-ray photoelectron spectroscopy (XPS) depth profiling. The present focus is depth profile quantification both in depth and chemical composition on a molecular level. The roughness of the samples is studied by atomic force microscopy before and after sputtering, and the erosion rate is determined by measuring the crater depth with a surface profilometer and vertical scanning interferometry. The resulting roughness (20-30 nm), being an order of magnitude lower than the crater depth (0.2-0.5 microm), allows layer-by-layer profiling, although the ion-induced effects result in an uncertainty of the depth calibration of a factor of 2. The XPS spectrum deconvolution and data evaluation applying target factor analysis allows chemical speciation on a molecular level. The elemental distribution as a function of the sputtering time is obtained, and the formation of two layers is observed-one hydroxide (mainly iron-nickel based) on top and a second one deeper, mainly consisting of iron-chromium oxides.     

Small silver particles in glass surface layers produced by sodium-silver ion exchange — their concentration and size depth profile

Small spherical silver particles in a surface layer of commercial flat glass were produced by means of sodium-silver ion exchange. In each volume element of the layer there is a Gaussian distribution of the particle diameters. The mean diameter increases with penetration depth. Within one individual sample it can vary from 4.5 nm immediately at the glass surface up to more than 50 nm at the end of the layer. Due to a special preparation technique the results were gained by microspectrophotometric measurements as well as by investigations carried out with the transmission electron microscope and the electron-probe microanalyzer on one and the same sample always as function of the penetration depth.     

Parallel processing of remotely sensed data: Application to the ATSR-2 instrument

Massively parallel computational paradigms can mitigate many issues associated with the analysis of large and complex remotely sensed data sets. Recently, the Beowulf cluster has emerged as the most attractive, massively parallel architecture due to its low cost and high performance. Whereas most Beowulf designs have emphasized numerical modeling applications, the Parallel Image Processing Environment (PIPE) specifically addresses the unique requirements of remote sensing applications. Automated, parallelization of user-defined analyses is fully supported. A neural network application, applied to Along Track Scanning Radiometer-2 (ATSR-2) data shows the advantages and performance characteristics of PIPE.     

Mesophase behaviour of 2,5-dibenzoyloxy-p-benzoquinone derivatives and tetrahydrobenzene tetraesters

The synthesis of 2,5-dibenzoyloxy-p-benzoquinone derivatives, their products after reduction and tetraesters from tetrahydroxybenzene prepared from those products is described. Their phase behaviour was investigated by differential scanning calorimetry and polarizing microscopy and is discussed in terms of their detailed structure.     

C^＊—模理论的若干结果

本文把代数结构与分析体系结合起来，运用同调的方法，较系统地确定了A上C^*－模的部分理论，这里A为复数域C上的交换C^*－代数。即不仅定义了与C^*－模有关的某些新概念，而且还得到了有关C^*－模的若干结果。