Nano-electrochemical detection of hydrogen or protons using palladium nanoparticles: distinguishing surface and bulk hydrogen.

The benefits of using nanoparticle-modified electrodes are exemplified through the electrochemical detection of protons and/or hydrogen. It is shown that a palladium-nanoparticle-modified boron-doped diamond allows voltammetric information relating to the relative roles played by the surface and the bulk metal to be obtained for the proton-hydrogen system at palladium surfaces which is not accessible using palladium macroelectrodes or microelectrodes.     

Gold ultra-microelectrode arrays: application to the steady-state voltammetry of hydroxide ion in aqueous solution.

Gold ultra-microelectrode arrays are used to explore the electrochemical oxidation of hydroxide ions and are shown to be analytical useful. Two types of ultra-microelectrode arrays are used; the first consist of 256 individual electrodes of 5 microm in radius, 170 of which are electrochemically active in a cubic arrangement which are separated from their nearest neighbour by a distance of 100 microm. The second array compromises 2597 electrodes of 2.5 microm in radius and of which 1550 of which are electrochemically active in a hexagonal arrangement separated by the nearest neighbour by 55 microm. Well defined voltammetric waves are found with peak currents proportional to the concentration of hydroxide ions in the range 50 microM to 1 mM. Detection limits of 20 microM using the 170 ultra-microelectrode and 10 microM with the 1550 ultra-microelectrode array are shown to be possible but with a higher sensitivity of 4 mA M(-1) observed using the 1550 ultra-microelectrode array compared to 1.2 mA M(-1) with the 170 ultra-microelectrode array.     

Voltammetric sizing of a sphere.

The size of a glass sphere positioned in the center of a microdisk electrode is determined by using a simple electrochemical procedure and is confirmed, additionally, by a microscopical measurement of the sphere at the time of the electrochemical measurement. The cyclic voltammetric response of the naked electrode and of the electrode with the sphere positioned in its center is recorded over a wide range of scan rates (0.002-1.5 V s(-1)). The size of the sphere is then determined by comparison of the experimental voltammogram with simulations for each individual scan rate.     

Anodic stripping voltammetry of sulphide at a nickel film: towards the development of a reagentless sensor

The determination of sulphide at an electrochemically generated nickel oxide layer at glassy carbon and screen-printed electrodes in acidic media has been examined and appraised. The NiO layer was found to produce a stripping-like signal to sulphide and gave a linear peak current response from 20 to 90 μM. The response was further enhanced by repetitive cycling allowing accumulation of nickel sulphide at the electrode surface such that lower micromolar levels of sulphide (i.e. 5 μM) can be determined. The response at the NiO layer to sulphide is shown to be reproducible over a period of 24 h, thereby offering the development of a disposable amperometric sensor for sulphide.     

Channel flow cell studies on the evaluation of surface pretreatments using phosphoric acid or polymaleic acid for calcite stone protection

The dissolution kinetics of surface-pretreated and weathered calcite was investigated in dilute acid using a channel flow cell with microdisk detection. Two pretreatments were studied, polymaleic acid and phosphoric acid. Treatment with polymaleic acid was shown to significantly passivate calcite but to a lesser extent than the phosphoric acid and the former coating was found to be less effective for protection of calcite from acid attack. However, treatment of calcite with phosphoric acid resulted in the passivation of calcite from acid attack which strongly inhibited dissolution, an effect that was enhanced even further after exposure to the environment.     

Dual microband electrodes: current distributions and diffusion layer ‘titrations’. Implications for electroanalytical measurements

The simulation of transport to double microband electrodes in generator–collector mode is reported focusing especially on the ‘titration curve’ approach to electroanalysis in which a titrant is electrogenerated from a redox active precursor on the generator electrode and reacts homogeneously with the target analyte. The current on the detector electrode reflects the amount of titrant ‘surviving’ passage between the two electrodes. The form of the titration curve – plots of detector current as a function of generator current – is shown to be highly sensitive to the electrode kinetics of the redox couple driven at the generator electrode. Accordingly the naïve use of such methodology for analysis without accompanying simulation and kinetic analysis is fraught with danger. Use of the conformal mapping approach in combination with the ADI method for investigation of the ‘titration’ current distributions at the double band system gives fast and precise simulation of this and similar problems. Convergence analysis is described which allows for the automatic selection of the simulation grid size so as to obtain a chosen accuracy (for example 1%) of the current for all experimentally meaningful values of the geometrical and physico-chemical parameters of the system to be investigated.