Mixing method influence on compatibility and polymorphism studies by DSC and statistical analysis

Most of the pharmaceutical products are formulated as solid dosage form, which may present drug–excipient interactions that lead to changes in the chemical nature of the drug, such as solubility and bioavailability and may compromise its safety and effectiveness. Differential scanning calorimetry (DSC) is a widely used method for the rapid evaluation of the drug-excipient compatibility and the stability of the mixture formed; however, there is no consensus on the preparation methods of the drug–excipient mixtures. The aim of this study was to investigate the influence of the mixing method on the drug–excipient compatibility studies by means of DSC analysis, using tenofovir disoproxil fumarate as a drug model. Statistical analysis revealed significant differences in the heat of fusion of the drug in the mixtures prepared by several mixing methods. Vortex Mixer with a Pop-Off Cup used for 3 min proved to be very satisfactory for these studies. A polymorphic transition was observed in the mixture prepared with the mortar and pestle. Therefore, this method should be avoided since it may induce errors in the interpretation of DSC results. In this way, the mixing method used to prepare a mixture for studies of interactions between the API and the excipients in a pharmaceutical formulation has a great influence on the results and it must be chosen carefully.     

Use of neutron activation analysis and LC–ICP-MS in the development of candidate reference materials for As species determination

Arsenic (As) is widely found in marine organisms, mainly as organic arsenical compounds. With the introduction of regulations for As species in foodstuffs and for environmental control, it has become more important to quantify the amount of arsenic species present. To address this concern new reference materials (RMs) for validation and quality assurance of As speciation measurements are being developed, including a tuna fish tissue and a robalo liver tissue. Instrumental neutron activation analysis (INAA) is used in this work as a proven analytical tool for As determinations and for validating the As mass fraction determined by liquid chromatography coupled to inductively coupled mass spectrometry (LC–ICP-MS) in extracts of the candidate RMs and other fish samples including certified RMs. Various methods for the extraction of water-soluble As species were evaluated. The best results were acquired after methanol/acetone/water extraction yielding in 93 % extractable As in the tuna RM. This procedure was used for the LC–ICP-MS studies. The results demonstrate that INAA can account for 100 % of the distribution of As species in analytical processes. It complements LC–ICP-MS for the validation of the characterization of As species in the development of RMs for such species. Excellent agreement of measured results in certified RMs with the reported values confirms the validity of the applied procedures.     

Physicochemical characterization of dipeptidyl peptidase-4 inhibitor alogliptin in physical mixtures with excipients

Alogliptin (ALG) is a hypoglycemic drug used in diabetes which inhibits the enzyme dipeptidyl peptidase-4 (DPP-4), preventing the degradation of incretins, stimulating insulin secretion. The physicochemical characteristics of ALG were evaluated by differential scanning calorimetry (DSC), thermogravimetry (TG) and scanning electron microscopy equipped with energy-dispersive X-ray spectrometer (SEM/EDS). The compatibility studies were carried out between ALG and excipients (physical mixtures, 1:1) using DSC, TG, diffuse reflectance Fourier transform infrared spectroscopy (FTIR), X-ray powder diffraction (XRPD) and hot-stage microscopy. ALG presented purity near to 99%, melted in the range of 179.4–187.2 °C, followed by decomposition which started in 198.0 °C. SEM/EMS analysis of ALG presented irregular crystals and traces of impurities as copper and lead. DSC investigations obtained by physical mixtures showed minor alterations in the melting ranges of ALG with mannitol, magnesium stearate and commercial tablets. Solubilization of ALG in the fused excipient was observed by hot-stage microscopy between mannitol and ALG, and in tablets. The interaction observed in the mixture with magnesium stearate is due to the melting of the excipient and drug separately, first the excipient and then the drug. FTIR showed additional bands related to the excipients. XRPD proved that ALG has a crystal form and no alterations in the ALG profile were observed after the mixtures. ALG was compatible with all excipients tested. These results were important to understand the characteristics, stability and compatibility of the drug, and proved to be useful in preformulation studies.

     

Feasibility of using solid sampling graphite furnace atomic absorption spectrometry for preparation of spiked filter papers with Cu and Zn as standards for direct solid analysis

An approach was developed for the preparation of cryogenic ground spiked filter papers with Cu and Zn for use as synthetic calibrating standards for direct solid microanalysis. Solid sampling graphite furnace atomic absorption spectrometry was used to evaluate the microhomogeneity and to check the applicability of the synthetic calibrating standards for the direct determination of Cu and Zn in vegetable certified reference materials. The found concentrations presented no statistical differences at the 95% confidence level. The homogeneity factors ranged from 2.7 to 4.2 for Cu and from 6.4 to 11.5 for Zn.     

Evaluation of laser induced breakdown spectroscopy for the determination of macronutrients in plant materials

Laser induced breakdown spectroscopy (LIBS) has become an analytical tool for the direct analysis of a large variety of materials in order to provide qualitative and/or quantitative information. However, there is a lack of information for LIBS analysis of agricultural and environmental samples. In this work a LIBS system has been evaluated for the determination of macronutrients (P, K, Ca, Mg) in pellets of vegetal reference materials. An experimental setup was designed by using a Nd:YAG laser operating at 1064 nm and an Echelle spectrometer with ICCD detector. The plasma temperature was estimated by Boltzmann plots and instrumental parameters such as delay time, lens-to-sample distance and pulse energy were evaluated. Certified reference materials as well as reference materials were used for analytical calibrations of P, K, Ca, and Mg. Most results of the direct analysis of plant samples by LIBS were in reasonable agreement with those obtained by ICP OES after wet acid decomposition.     

Optimization of in situ derivatization SPME by experimental design for GC-MS multi-residue analysis of pharmaceutical drugs in wastewater

This paper presents the development of a procedure, which enables the analysis of nine pharmaceutical drugs in wastewater using gas chromatography‐mass spectrometry (GC‐MS) associated with solid‐phase microextraction (SPME) for the sample preparation. Experimental design was applied to optimize the in situ derivatization and the SPME extraction conditions. Ethyl chloroformate (ECF) was employed as derivatizing agent and polydimethylsiloxane‐divinylbenzene (PDMS‐DVB) as the SPME fiber coating. A fractional factorial design was used to evaluate the main factors for the in situ derivatization and SPME extraction. Thereafter, a Doehlert matrix design was applied to find out the best experimental conditions. The method presented a linear range from 0.5 to 10 μg/L, and the intraday and interday precision were lower than 16%. Applicability of the method was verified from real influent and effluent samples of a wastewater treatment plant, as well as from samples of an industry wastewater and a river.     

Multielement determination of cadmium and lead in urine by simultaneous electrothermal atomic absorption spectrometry with an end-capped graphite tube.

A method for the multielement determination of cadmium and lead in urine is proposed by simultaneous electrothermal atomic absorption spectrometry (SIMAAS) with an end-capped transversely heated graphite atomizer (EC-THGA). The best conditions for cadmium and lead determination were obtained in the presence of NH4H2PO4 as a chemical modifier, using 500 degrees C and 1800 degrees C as the pyrolysis and atomization temperatures, respectively. Urine samples were diluted 1 + 4 directly in autosampler cups with a mixture of 0.125% (w/v) Triton X-100 + 2.5% (v/v) HNO3 + 0.31% (w/v) NH4H2PO4. The optimized heating program was carried out in 57 s, and the instrument calibration was done with aqueous reference solutions. The use of EC-THGA increased the sensitivity of cadmium and lead by 14% and 25%, respectively. The detection limits (n = 20, 3delta) were 0.03 microg L(-1) (0.36 pg) for cadmium and 0.57 microg L(-1) (6.8 pg) for lead. The performance of EC-THGA was acceptable up to 500 heating cycles. The reliability of the entire procedure was checked with the analysis of a lyophilized urine certified reference material. The found concentrations were in agreement with the recommended values (95% confidence level).     

Direct determination of iron in sand using solid sampling graphite furnace atomic absorption spectrometry

A fast and reliable method for the direct determination of iron in sand by solid sampling graphite furnace atomic absorption spectrometry was developed. A Zeeman-effect 3-field background corrector was used to decrease the sensitivity of spectrometer measurements. This strategy allowed working with up to 200 μg of samples, thus improving the representativity. Using samples with small particle sizes (1–50 μm) and adding 5 μg Pd as chemical modifier, it was possible to obtain suitable calibration curves with aqueous reference solutions. The pyrolysis and atomization temperatures for the optimized heating program were 1400 and 2500 °C, respectively. The characteristic mass, based on integrated absorbance, was 56 pg, and the detection limits, calculated considering the variability of 20 consecutive measurements of platform inserted without sample was 32 pg. The accuracy of the procedure was checked with the analysis of two reference materials (IPT 62 and 63). The determined concentrations were in agreement with the recommended values (95% confidence level). Five sand samples were analyzed, and a good agreement (95% confidence level) was observed using the proposed method and conventional flame atomic absorption spectrometry. The relative standard deviations were lower than 25% (n = 5). The tube and boat platform lifetimes were around 1000 and 250 heating cycles, respectively. Correspondence: Pedro V. Oliveira, Instituto de Química, Universidade de S?o Paulo, CP 26077, 05513-970 S?o Paulo, SP, Brazil