Large-scale computer simulation of fully developed turbulent channel flow with heat transfer

Recently, with the advent of supercomputers, there has been considerable interest in the use of direct numerical simulation to obtain information about turbulent shear flow at low Reynolds number. This paper presents a pseudospectral technique to solve the full three-dimensional time-dependent Navier-Stokes and advection-diffusion equations without the use of subgrid-scale modelling. The technique has not been previously used for fully developed turbulent channel flow simulation and is based on methods applied in other contexts. The emphasis of this paper is to provide a reasonably detailed account of how the simulation is done rather than to present new calculations of turbulence. The details of an algorithm for turbulent channel flow simulation and the grid and time step sizes needed to integrate through transient behaviour to steady state turbulence have not been published before and are presented here. Results from a Cray-2 simulation of fully developed turbulent flow in a channel with heat transfer are presented along with a critical comparison between experiment and computation. The first- and second-order moments agree well with experimental measurements; the agreement is poor for higher-order moments such as the skewness and flatness near the walls of the channel. Detailed information given about the effects of spatial grid resolution on a computed results is important for estimating the size of the computation required to study various aspects of a turbulent flow.     

Monitoring photoproduct formation and photobleaching by fluorescence spectroscopy has the potential to improve PDT dosimetry with a verteporfin-like photosensitizer

In current clinical practice, photodynamic therapy (PDT) is carried out with prescribed drug doses and light doses as well as fixed drug-light intervals and illumination fluence rates. This approach can result in undesirable treatment outcomes of either overtreatment or undertreatment because of biological variations between different lesions and patients. In this study, we explore the possibility of improving PDT dosimetry by monitoring drug photobleaching and photoproduct formation. The study involved 60 mice receiving the same drug dose of a novel verteporfin-like photosensitizer, QLT0074, at 0.3 mg/kg body weight, followed by different light doses of 5, 10, 20, 30, 40 or 50 J/cm2 at 686 nm and a fluence rate of 70 mW/cm2. Photobleaching and photoproduct formation were measured simultaneously, using fluorescence spectroscopy. A ratio technique for data processing was introduced to reliably detect the photoproduct formed by PDT on mouse skin in vivo. The study showed that the QLT0074 photoproduct is stable and can be reliably quantified. Three new parameters, photoproduct score (PPS), photobleaching score (PBS) and percentage photobleaching score (PBS%), were introduced and tested together with the conventional dosimetry parameter, light dose, for performance on predicting PDT-induced outcome, skin necrosis. The statistical analysis of experimental results was performed with an ordinal logistic regression model. We demonstrated that both PPS and PBS improved the prediction of skin necrosis dramatically compared to light dose. PPS was identified as the best single parameter for predicting the PDT outcome.     

The oxidation of water by cerium(IV) catalysed by nanoparticulate RuO2 on mesoporous silica

Mesoporous silicates are prepared by templating on the hexagonal (H1) mesophase of surfactant bipyridine complexes of ruthenium(II) using a true liquid-crystal templating approach. On calcination, the surfactant template is removed except for the central metal ion that is oxidised, forming nanoparticles of RuO2 that deposit within the pores. RuO2 is a known oxidation catalyst and, despite its anhydrous nature in these silicates, is found to be very active in catalyzing the oxidation of water by acidic CeIV.     

Growth of porous single-crystal Cr2O3 in a 3-D mesopore system

Single-crystal Cr2O3 with regular mesopores has been synthesized using mesoporous silica KIT-6 as a template and characterized by using XRD, HRTEM and nitrogen adsorption/desorption.     

Mild and practical method for the alpha-arylation of nitriles with heteroaryl halides

[reaction: see text] A mild and transition-metal-free method for the alpha-arylation of aliphatic nitriles with activated heteroaryl halides was developed using NaHMDS or KHMDS as base at ambient temperature. The key to the success of this method is generation of the nitrile anion in the presence of the heteroaryl halide. The method is applicable to both primary and secondary carbonitriles and a wide range of heteroaryl halides. Selective monoarylation was observed with primary carbonitriles. The operational simplicity and the mild reaction conditions add to the value of this method as a practical alternative to the preparation of alpha-heteroaryl carbonitriles.     

Viscosity for a dense fluid of square-well rough spheres

Shear viscosity is calculated for a dense fluid of square-well rough spheres. The results are compared with calculated shear viscosities for the familiar hard-sphere, square-well and rough-sphere models.     

Measurement of labile Cu in soil using stable isotope dilution and isotope ratio analysis by ICP-MS

Isotope dilution is a useful technique to measure the labile metal pool, which is the amount of metal in soil in rapid equilibrium (<7 days) with the soil solution. This is normally performed by equilibrating soil with a metal isotope, and sampling the labile metal pool by using an extraction (E value), or by growing plants (L value). For Cu, this procedure is problematic for E values, and impossible for L values, due to the short half-life of the ⁶⁴Cu radioisotope (12.4 h), which makes access and handling very difficult. We therefore developed a technique using enriched ⁶⁵Cu stable isotope and measurement of ⁶³Cu/⁶⁵Cu ratios by quadrupole inductively coupled plasma mass spectrometry (ICP-MS) to measure labile pools of Cu in soils using E value techniques. Mass spectral interferences in detection of ⁶³Cu/⁶⁵Cu ratios in soil extracts were found to be minimal. Isotope ratios determined by quadrupole ICP-MS compared well to those determined by high-resolution (magnetic sector) ICP-MS. E values determined using the stable isotope technique compared well to those determined using the radioisotope for both uncontaminated and Cu-contaminated soils.     

Thin film platinum cuff electrodes for neurostimulation: in vitro approach of safe neurostimulation parameters

Thin film technology takes more and more importance in the development of biomedical devices dedicated to functional neurostimulation. Our research about the design of implant neurostimulating electrode is oriented toward thin film cuff electrodes based on a polyimide substrate covered by a chromium/gold/Pt film. The chromium/gold sputtered film serves as adhesion layer and current collector whereas platinum acts as an electrochemical actuator. The electrode surface has been designed to obey safe stimulation criteria (i.e. chemically inert noble metal, low electrode-electrolyte impedance, high electrochemical reversibility, high corrosion stability). The electrochemical behaviour of such platinum electrodes has been assessed and compared to a foil of platinum. Extensive in vitro characterisations of the both electrode types were carried out using AFM, SEM and electrochemical techniques. The role of enhanced surface roughness enabling high double layer capacitances to be achieved was clearly highlighted. The obtained results are discussed, with particular reference to thin film electrodes stability under in vitro electrical stimulation in NaCl 0.9% (physiological serum). Therefore, these thin film devices showed reversible PtOH formation and decomposition making them potentially attractive for the fabrication of implant stimulation cuff electrodes.