A study of electrostatic spring softening for dual-axis micromirror

Electrostatic spring softening is an important characteristic of electrostatically actuated dual-axis micromirror, since it lowers the resonant frequencies. This paper presents an approach based on approximating the electrostatic forces by the first-order Taylor's series expansion to investigate this characteristic. The dual-axis micromirror studied in this paper has three motion modes, two torsional (about x- and y-axis, respectively) and one translational (about z-axis). The stiffnesses of all these modes are softened by a DC bias voltage applied to the mirror plate. The resonant frequencies are lowered with the increment of the bias voltage. The relationship of the bias voltage and the resonant frequencies of all the motion modes is derived. The analytical results show that the resonant frequency curves are affected by the capacitor geometries, i.e. the gap between the mirror plate and the electrodes and the electrodes size. The lowering curves drop slowly when the bias voltage is small. While for large bias voltage, the lowering curves drop rapidly. The experiment results are consistent with those obtained by the analytical approach.     

Adsorptive stripping voltammetric determination of traces of molybdenum in natural water in the presence ofα-benzoinoxime

The electrochemical behavior of the molybdenum complex of -benzoinoxime was investigated using cyclic voltammetry and linear scan voltammetry, after adsorptive accumulation of the complex onto a hanging mercury drop electrode (HMDE). The signal corresponds to the reduction of molybdenum in the complex adsorbed at the HMDE surface. Under optimal conditions, the adsorptive stripping voltammetric procedure gave an extremely low detection limit of 0.1 nM (9.6ng/l) Mo(VI) following stirred accumulation for 5 min at 0.0 V (vs. Ag/AgCl). The reduction cur rent-[Mo(VI)] relationships were linear up to 25 and 100 nM. Repetitive determinations of 10 nM solutions gave relative standard deviations of 2.2 and 3.5%, for 1 and 5-min accumulation periods, respectively. Most of the ions investigated did not interfere with the determination of molybdenum, except for tungsten. Excellent selectivity against copper was observed. The proposed procedure was applied to the direct determination of molybdenum in natural water.     

X-Ray Structure and Proton NMR Study of a Hexacoordinated Lithium Complex

The structure of the lithium complex with1,3,5-tris[oxymethylene(N,N-dicyclohexyl)carboxyamido]cyclohexanehas been determined by the X-ray method.The compound is triclinic, space group P¯1,a = 15.623(3), b = 19.279(4),c = 19.295(4)Å = 102.32(3), = 92.45(3), = 105.67(3)0, V = 5436(2)Å3, Z = 4. Itscomposition is represented by the formulaC48H82N3O6LiI 0.5H2O. The lithium cationis encapsulated in a polar pseudo-cavity of six oxygen atoms of the ligandmolecule and displays a distorted trigonal prism coordination. The conformationof the ligand in the solid state complex has been compared with the conformationof the complex in solution determined by 1H-NMR measurements.Supplementary data relevant to this publication have been deposited with the British Library, No. SUP 82224 (21 pages).     

Filter-based microfluidic device as a platform for immunofluorescent assay of microbial cells

A filter-based microfluidic device was combined with immunofluorescent labeling as a platform to rapidly detect microbial cells. The coin-sized device consisted of micro-chambers, micro-channels and filter weirs (gap = 1-2 microm), and was demonstrated to effectively trap and concentrate microbial cells (i.e., Cryptosporidium parvum and Giardia lamblia), which were larger in size than the weir gap. After sample injection, a staining solution containing fluorescently-labeled antibodies was continuously provided into the device (flow rate = 20 microl min(-1)) to flush the microbial cells toward the weirs and to accelerate the fluorescent labeling reaction. Using a staining solution that was 10 to 100 times more dilute than the recommended concentration used in a conventional glass method, those target cells with a fluorescent signal-to-noise ratio of 12 could be microscopically observed at single-cell level within 2 to 5 min prior to secondary washing.     

High‐efficiency polymer solar cells based on phenylenevinylene copolymer with BF2‐azopyrrole complex and CN‐PC70BM with solvent additive

Power conversion efficiency (PCE) of phenylenevinylene‐based copolymer with BF₂ azopyrrole complex (PB)/modified PC₇₀BM, that is, CN‐PC₇₀BM bulk heterojunction solar cells improves from 2.16 to 4.90% using a processing additive and drying condition. The results demonstrate that a processing additive and drying condition provides an effective means to control both the surface roughness and finer interpenetrating networks to enhance the exciton dissociation into free charge carriers, charge transportation, and collection. Taking into the account of simple device fabrication process without thermal annealing, the PCE of the polymer solar cell can further improved by chloronapthalene (CN) additive under the fast drying condition. The average carrier lifetimes extracted from the impedance spectra and found to correlate with measured PCEs. At short circuit conditions and illumination, the average charge carrier lifetime was found vary from 16.8 to 32 μs with power conversion efficiencies ranging from 3.0 to 4.9%. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Experimental results on neutrino-electron scattering

A determination of sin² θ _w based on measurements of elastic scattering of muon-neutrinos and muon-anti-neutrinos on atomic electrons is described. These purely leptonic processes were studied using the CHARM calorimeter exposed to neutrino and antineutrino wide-band beams at the CERN super proton synchrotron. A total of 83±16 neutrino-electron and 112±21 antineutrino-electron events have been detected. From the measurement of the ratio of muon-neutrino and muon-antineutrino cross-sections a value of sin² θ _w =0.211±0.037 was obtained.     

Properties of a vector soliton laser passively mode-locked by a fiber-based semiconductor saturable absorber operating in transmission

We experimentally demonstrate a passively mode-locked fiber laser employing a fiber-based semiconductor saturable absorber (SSA) operating in transmission. Polarization rotation locked vector solitons are observed in the laser. Due to the intrinsic dynamic feature of the laser, period-doubling of these vector solitons has also been observed. Furthermore, extra spectral sidebands are formed on the optical spectrum, caused by the energy exchange between the two orthogonal polarization components of the vector solitons. By careful reduction of the pump power together with fine adjustment to the cavity birefringence, period-one state can further be obtained. Additionally, the phase noise properties of the vector soliton fiber laser have also been characterized experimentally and analytically.     

Truncation rules for modelling discontinuities with Galerkin method in electromagnetic theory

It is well known that apparently similar discretization schemes of Maxwell's equations in Fourier series may provide very different convergence performances because of truncation. We argue that this work performed in grating theory can be applied to other electromagnetic theories relying on expansions over series different from Fourier series. This generalization is supported by an intuitive argument and by a simple numerical example with Hermite–Gauss functions.     

Numerical study of steady/unsteady flow and heat transfer in porous media using a characteristics-based matrix-free implicit FV method on unstructured grids

In this study, a high-resolution characteristic-based finite-volume (FV) method on unstructured grids [Int. J. Numer. Method Eng. 50 (2001) 11; Int. J. Heat Fluid Flow 21 (2000) 432] is extended by a matrix-free implicit dual-time stepping scheme for the numerical simulation of steady and unsteady flow and heat transfer with porous media. The method has been used to study the characteristics of a complex problem: flow and heat transfer in a channel with multiple discrete porous blocks, which was originally proposed by Huang and Vafai [J. Thermophys. Heat Transfer 8 (3) (1994) 563]. In addition, flow and heat transfer in a channel partially or fully filled with porous layers and containing solid protruding blocks with constant heat flux on its lower surface are also investigated in details. Hydrodynamic and heat transfer results are reported for both steady and transient flow cases. In particular, the effects of Darcy and Reynolds numbers on heat transfer augmentation and pressure loss are studied. An in-depth discussion of the formation and variation of recirculation is presented and the existence of optimum porous insert is demonstrated. At high Reynolds numbers the flow in the porous channel exhibits a cyclic characteristics although unlike the non-porous channel flow, the cyclic vortex development is only restricted to a small area behind the last solid block, while temperature changes more slowly and does not exhibit cyclic variations over a long period of time. It is shown that for all the cases studied altering some parametric values can have significant and interesting effects on both flow pattern as well as heat transfer characteristics.