Electrokinetic and contact angle measurements of grafted carbon fibers

 The grafting method that has successfully been applied to methacrylic acid and liquid crystalline monomers was expanded to prepare amphoteric carbon fiber surfaces using 2-(N,N-dimethylamino)ethyl methacrylate as monomer. The obtained carbon fiber surfaces were characterized by contact angle and ζ-potential measurements. The expected basic behavior was not observed, instead an amphoteric character of the modified carbon fiber surface was found. The fiber surfaces display a basic character in the acidic pH-range, while they are acidic in the alkaline part of the pH-scale. An important influence is derived from the amount of initiator used to graft the monomers onto the fibers. The smaller the initiator concen-tration used during polymerization, the larger the amount of amino functionalities introduced to the carbon fiber surface. The wetting behavior versus water depends on the overall conformation of the immobilized polymer. During immersion into water the polymer acts hydrophobic, while during emersion, a hydrophilic character is observed, probably derived from conformational changes and swelling during the contact angle measure-ments in water. Received: 9 June 1998 Accepted: 13 August 1998     

Surface and bulk properties of severely fluorinated carbon fibres

The development of ultra-inert composites using fluorinated carbon fibres as the reinforcement requires fluorinated carbon fibres with a durable surface composition. Here we report the effect of direct fluorination using an F₂/N₂ mixture at 653 K on the surface and bulk properties of two types of high strength carbon fibres. These were treated up to a surface fluorine content of ∼64 at.% and a bulk fluorine content of ∼15 mass%. A colour change was observed after fluorination caused by the changes in the graphitic band structure of the carbon fibres by the introduction of carbon sp³ hybridisation. The tensile strength and Young's modulus decrease after fluorination by up to 33 and 22%, respectively. XRD shows marginal changes in the interlayer distance but the crystallite size increases. Changes in the electrical conductivity of the fluorinated carbon fibres indicate that the modification is confined to the near surface volume. Predominantly covalent C-F bonds are formed as shown by X-ray photoelectron spectroscopy (XPS) and measured zeta (ζ)-potentials. Hence the fluorinated fibres are hydrophobic and have low surface tensions. This and the large increase in fibre surface area, as determined by nitrogen adsorption, is expected to facilitate interfacial interaction between fluorinated carbon fibres and fluoropolymers.     

Injectable,Interconnected, High‐Porosity Macroporous Biocompatible Gelatin Scaffolds Made by Surfactant‐Free Emulsion Templating

High‐porosity interconnected, thermoresponsive macroporous hydrogels are prepared from oil‐in‐water high internal phase emulsions (HIPEs) stabilized by gelatin‐graft‐poly(N‐isopropylacrylamide). PolyHIPEs are obtained by gelling HIPEs utilizing the thermoresponsiveness of the copolymer components. PolyHIPEs properties can be controlled by varying the aqueous phase composition, internal phase volume ratio, and gelation temperature. PolyHIPEs respond to temperature changes experienced during cell seeding, allowing fibroblasts to spread, proliferate, and penetrate into the scaffold. Encapsulated cells survive ejection of cell‐laden hydrogels through a hypodermic needle. This system provides a new strategy for the fabrication of safe injectable biocompatible tissue engineering scaffolds.

     

Self-reinforced cellulose nanocomposites

A self-reinforced cellulosic material was produced exclusively from regenerated cellulose microcrystals. The level of reinforcement was controlled by tailoring the crystallinity of cellulose by controlling the dissolution of microcrystalline cellulose (MCC) before its regeneration process. After the cellulose regeneration a self-reinforced material was obtained in which cellulose crystals reinforced amorphous cellulose. This structure was produced by dissolution of MCC in a non-derivatising cosolvent N,N-dimethylacetamide/LiCl followed by subsequent cellulose regeneration in distilled H₂O. The reduction of the overall crystallinity of self-reinforced regenerated cellulose was dependent on the dissolution time of the cellulose precursor. The crystallinity of regenerated cellulose was determined by wide angle X-ray diffraction. A reduction in crystal size from microcrystalline cellulose to regenerated cellulose was observed with increasing dissolution time in DMAc/LiCl cosolvent. The reduction in degree of crystallinity of regenerated cellulose led to a decrease in the tensile mechanical performance and thermal stability of the regenerated cellulose. The controlled dissolution of microcrystalline cellulose resulted in the modification of structural, physical, thermal properties and moisture uptake behaviour of regenerated cellulose.     

Crosslinked integrally skinned asymmetric polyaniline membranes for use in organic solvents

Solvent stable integrally skinned asymmetric nanofiltration membranes were prepared from polyaniline. These membranes were made by phase inversion and then crosslinked using two different chemical crosslinkers, α,α′-dichloro-p-xylene and glutaraldehyde. The resultant membranes were found to be stable in various organic solvents including acetone, methanol, ethyl acetate, tetrahydrofuran and N,N-dimethyl formamide. Nanofiltration experiments carried out in acetone and dimethyl formamide showed that the membranes gave stable permeate fluxes and good separation performances in the nanofiltration range. Molecular weight cut-off (MWCO) of the membranes was found to be between 150 and 250 g mol⁻¹. These membranes were also found to be stable for operations at elevated temperatures up to 70 °C and possibly higher. Furthermore, no fillers or preservative agents are required to maintain the membranes in a dry state thereby increasing the ease of handling.     

Macroporous polymers obtained in highly concentrated emulsions stabilized solely with magnetic nanoparticles

Magnetic macroporous polymers have been successfully prepared using Pickering high internal phase ratio emulsions (HIPEs) as templates. To stabilize the HIPEs, two types of oleic acid-modified iron oxide nanoparticles (NPs) were used as emulsifiers. The results revealed that partially hydrophobic NPs could stabilize W/O HIPEs with an internal phase above 90%. Depending upon the oleic acid content, the nanoparticles showed either an arrangement at the oil-water interface or a partial dispersion into the oil phase. Such different abilities to migrate to the interface had significant effects on the maximum internal phase fraction achievable and the droplet size distribution of the emulsions. Highly macroporous composite polymers were obtained by polymerization in the external phase of these emulsions. The density, porosity, pore morphology and magnetic properties were characterized as a function of the oleic acid content, concentration of NPs, and internal phase volume of the initial HIPEs. SEM imaging indicated that a close-cell structure was obtained. Furthermore, the composite materials showed superparamagnetic behavior and a relatively high magnetic moment.     

Bacterial Cellulose Nanopaper as Reinforcement for Polylactide Composites: Renewable Thermoplastic NanoPaPreg

Bacterial cellulose (BC) is often regarded as a prime candidate nano‐reinforcement for the production of renewable nanocomposites. However, the mechanical performance of most BC nanocomposites is often inferior compared with commercially available polylactide (PLLA). Here, the manufacturing concept of paper‐based laminates is used, i.e., “PaPreg,” to produce BC nanopaper reinforced PLLA, which has been called “nanoPaPreg” by the authors. It is demon­strated that high‐performance nanoPaPreg (v_f = 65 vol%) with a tensile modulus and strength of 6.9 ± 0.5 GPa and 125 ± 10 MPa, respectively, can be fabricated. It is also shown that the tensile properties of nanoPaPreg are predominantly governed by the mechanical performance of BC nanopaper instead of the individual BC nanofibers, due to difficulties impregnating the dense nanofibrous BC network.

     

High internal phase emulsion templates solely stabilised by functionalised titania nanoparticles

Porous polymer foams (poly-Pickering-HIPEs) have been synthesised from stable high internal phase emulsion templates solely stabilised by low concentrations of functionalised titania nanoparticles.     

Nanoporous asymmetric polyaniline films for filtration of organic solvents

A new family of functional materials is reported for organic solvent nanofiltration, with excellent chemical stability and high retention of solute molecules. Integrally skinned asymmetric polyaniline (PANI) membranes were fabricated from concentrated solutions of doped PANI by phase inversion. Doped PANI solutions were prepared by adding organic acids directly to PANI dissolved in a mixture of NMP and 4-methyl piperidine before casting. Among the organic acids investigated, maleic acid, phthalic acid, sulfosalicylic acid and camphorsulfonic acid were able to dope PANI without causing gelation. These acids acted as soft templates, creating nanoporosity in the thin skin layer of the asymmetric PANI film. Their removal by alkaline extraction created membranes through which small solvent molecules can pass. After extracting the organic acids, the membranes were thermally crosslinked which conferred excellent solvent stability. These membranes had a molecular weight cut-off (MWCO) in the range of 150–250 g mol⁻¹ in methanol, making them the tightest OSN membranes reported to date. It was found that an increase in crosslinking temperature or time led to a decrease in solvent flux. PANI membranes were found to be resistant to a variety of organic solvents such as ethyl acetate, acetonitrile and acetone. These remarkable membranes have the potential to be used in OSN operations at high temperatures (up to 150 °C), and gave increasing fluxes with increasing temperature while maintaining a high solute rejection.