Intracellular Delivery and Triggered Release of DNA Using Biodegradable Poly(2‐hydroxypropylene imine)s Containing Cystamine Units

Poly(2‐hydroxypropylene imine)s containing segments of cystamine (PHPI‐CA) are synthesized by polycondensation of 1,3‐dibromo‐2‐propanol with a mixture of 1,3‐diamino‐2‐propanol and cystamine. High molecular weight fractions of these polymers are collected by ultrafiltration and characterized by chemical analysis, ¹H and ¹³C‐NMR spectroscopy, size‐exclusion chromatography with triple detection, and potentiometric titration, and are tested for DNA delivery in vitro. It is shown that PHPI‐CA are highly branched polymers containing disulfide linkages. Transfection efficiency of PHPI‐CA for DNA gives similar results to that of PHPI with GFP⁺ cell percent reaching 80–90%. Cytotoxicity levels for PHPI‐CA are lower than that of PHPI. Novel polymers containing different amounts of disulfide linkages are able to disintegrate and release DNA following the treatment with reducing agent 1,4‐dithiothreitol. Downstream application of PHPI‐CA transfected cells for RNA purification shows that RNA yield is not affected even after the double transfection suggesting that these polymers could be great candidates for in vitro and in vivo transfection.

     

Surface properties of bottle-brush polyelectrolytes on mica: effects of side chain and charge densities

Surface properties of a series of cationic bottle-brush polyelectrolytes with 45-unit-long poly(ethylene oxide) side chains were investigated by phase modulated ellipsometry and surface force measurements. The evaluation of the adsorbed mass of polymer on mica by means of ellipsometry is complex due to the transparency of mica and its birefringence and low dielectric constant. We therefore employed a new method to overcome these difficulties. The charge and the poly(ethylene oxide) side chain density of the bottle-brush polymers were varied from zero charge density and one side chain per segment to one charge per segment and no side chains, thus spanning the realm from a neutral bottle-brush polymer, via a partly charged brush polyelectrolyte, to a linear fully charged polyelectrolyte. The adsorption properties depend crucially on the polymer architecture. A minimum charge density of the polymer is required to facilitate adsorption to the oppositely charged surface. The maximum adsorbed amount and the maximum side chain density at the surface are obtained for the polymer with 50% charged segments and the remaining 50% of the segments carrying poly(ethylene oxide) side chains. It is found that brushlike layers are formed when 25-50% of the segments carry poly(ethylene oxide) side chains. In this paper, we argue that the repulsion between the side chains results in an adsorbed layer that is non-homogeneous on the molecular level. As a result, not all side chains will contribute equally to the steric repulsion but some will be stretched along the surface rather than perpendicular to it. By comparison with linear polyelectrolytes, it will be shown that the presence of the side chains counteracts adsorption. This is due to the entropic penalty of confining the side chains to the surface region.     

Soluble complexes in aqueous mixtures of low charge density comb polyelectrolyte and oppositely charged surfactant probed by scattering and NMR

A low charge density polyelectrolyte with a high graft density of 45 units long poly(ethylene oxide) side-chains has been synthesized. In this comb polymer, denoted PEO(45)MEMA:METAC-2, 2 mol% of the repeating methacrylate units in the polymer backbone carry a permanent positive charge and the remaining 98 mol% a 45 unit long PEO side-chain. Here we describe the solution conformation of this polymer and its association with an anionic surfactant, sodium dodecylsulfate, SDS. It will be shown that the polymer can be viewed as a stiff rod with a cross-section radius of gyration of 29 A. The cross section of the rod contracts with increasing temperature due to decreased solvency of the PEO side-chains. The anionic surfactant associates to a significant degree with PEO(45)MEMA:METAC-2 to form soluble complexes at all stoichiometries. A cooperative association is observed as the free SDS concentration approaches 7 mM. At saturation the number of SDS molecules associated with the polymer amounts to 10 for each PEO side-chain. Two distinct populations of associated surfactants are observed, one is suggested to be molecularly distributed over the comb polymer and the other constitutes small micellar-like structures at the periphery of the aggregate. These conclusions are reached based on results from small-angle neutron scattering, static light scattering, NMR, and surface tension measurements.     

Adsorption characteristics of bottle-brush polymers on silica: effect of side chain and charge density

The adsorption behavior of bottle-brush polymers with different charge/PEO ratio on silica was studied using optical reflectometry and QCM-D. The results obtained under different solution conditions clearly demonstrate the existence of two distinct adsorption mechanisms depending on the ratio of charge/PEO. In the case of low-charge density brush polymers (0-10 mol %), the adsorption occurs predominantly through the PEO side chains. However, the presence of a small amount of charge along the backbone (as low as 2 mol %) increases the adsorption significantly above that of the uncharged bottle-brush polymer in pure water. As the charge density of the brush polymers is increased to 25 mol % or larger the adsorption occurs predominantly through electrostatic interactions. The adsorbed layer structure was studied by measuring the layer dissipation using QCM-D. The adsorbed layer formed by the uncharged brush polymer dissipates only a small amount of energy that indicates that the brush lie along the surface, the scenario in which the maximum number of PEO side chains interact with the surface. The adsorbed layers formed by the low-charge density brush polymers (2-10 mol %) in water are more extended, which results in large energy dissipation, whereas those formed by the high-charge density brush polymers (50-100 mol %) have their backbone relatively flat on the surface and the energy dissipation is again low.     

Competitive adsorption of neutral comb polymers and sodium dodecyl sulfate at the air/water interface

The interfacial behavior of aqueous solutions of four different neutral polymers in the presence of sodium dodecyl sulfate (SDS) has been investigated by surface tension measurements and ellipsometry. The polymers comprised linear poly(ethylene oxide) with low and high molecular masses (10(3) and 10(6) Dalton (Da), respectively), and two high molecular mass methacrylate-based comb polymers containing poly(ethylene oxide) side chains. The adsorption isotherms of SDS, determined by Gibbs analysis of surface tension data, are nearly the same in the presence of the high molecular mass linear polymer and the comb polymers. Analysis of the ellipsometric data reveals that while a single surface layer model is appropriate for films of polymer alone, a more sophisticated interfacial layer model is necessary for films of SDS alone. For the polymer/surfactant mixtures, a novel semiempirical approach is proposed to determine the surface excess of polymer, and hence quantify the interfacial composition, through analysis of data from the two techniques. The replacement of the polymer due to surfactant adsorption is much less pronounced for the high molecular mass linear polymer and for the comb polymers than for the low molecular mass linear polymer. This finding is rationalized by the significantly higher adsorption driving force of the larger polymer molecules as well as by their more amphiphilic structure in the case of the comb polymers.