The photon transmission technique was used to monitor the evolution of transparency during film formation from nanosized copolymeric latex particles. The latex films were prepared from poly(methyl methacrylate-co-butyl methacrylate) (P(MMA-co-BMA)) particles which were produced by microemulsion polymerization. These films were annealed at elevated temperatures in various time intervals above the glass transition temperature (T(g)) of P(MMA-co-BMA). It is observed that the transmitted photon intensity (I(tr)) from these films increased as the annealing temperature increased. There are three different film formation stages. These stages are explained by the void closure, healing, and interdiffusion processes, respectively. The activation energies for viscous flow (DeltaH approximately 16 kcal/mol), minor chains (DeltaE(H) approximately 27 kcal/mol), and backbone motion (Delta E(b) approximately 132 kcal/mol) were obtained using various models. Void closure (tau(v), T(v)) and healing points (tau(H), T(H)) were determined. Using the time-temperature pairs, void closure and healing activation energies were measured and found to be 21 and 30 kcal/mol, respectively. Copyright 2001 Academic Press. 相似文献
Recently the connection between oxidative stress and various diseases, including cancer and Alzheimer's, attracts notice as a pathway suitable for diagnostic purposes. 8‐Oxo‐deoxyguanosine and 8‐oxo‐deoxyadenosine produced from the interaction of reactive oxygen species with DNA become prominent as biomarkers. Several methods have been developed for their determination in biofluids, including solid‐phase extraction and enzyme‐linked immunosorbent assays. However, still, there is a need for reliable and fast analytical methods. In this context, solid‐phase microextraction offers many advantages such as flexibility in geometry and applicable sample volume, as well as high adaptability to high‐throughput sampling. In this study, a solid‐phase microextraction method was developed for the determination of 8‐oxo‐deoxyguanosine and 8‐oxo‐deoxyadenosine in biofluids. The extractive phase of solid‐phase microextraction consisted of hydrophilic–lipophilic balanced polymeric particles. In order to develop a solid‐phase microextraction method suitable for the determination of the analytes in saliva and urine, several parameters, including desorption solvent, desorption time, sample pH, and ionic strength, were scrutinized. Analytical figures of merit indicated that the developed method provides reasonable interday and intraday precisions (<15% in both biofluids) with acceptable accuracy. The method provides a limit of quantification for both biomarkers at 5.0 and 10.0 ng/mL levels in saliva and urine matrices, respectively. 相似文献
Fuel-rich combustion of methane in a homogeneous-charge compression-ignition (HCCI) engine can be used as a polygeneration process producing work, heat, and useful chemicals like syngas. Due to the inertness of methane, additives such as dimethyl ether (DME) are needed to achieve ignition at moderate inlet temperatures and to control combustion phasing. Because significant concentrations of DME are then needed, a considerable part of the fuel energy comes from DME. An alternative ignition promotor known from fuel-lean HCCI is ozone (O3). Here, a combined experimental and modelling study on the ignition of fuel-rich partial oxidation of methane/air mixtures at Φ = 1.9 with ozone and DME as additives in an HCCI engine is conducted. Experimental results show that ozone is a suitable additive for fuel-rich HCCI, with only 75 ppm ozone reducing the fuel-fraction of DME needed from 11.0% to 5.3%. Since ozone does not survive until the end of the compression stroke, the reaction paths are analyzed in a single-zone model. The simulation shows that different ignition precursors or buffer molecules are formed, depending on the additives. If only DME is added, hydrogen peroxide (H2O2) and formaldehyde (CH2O) are the most important intermediates, leading to OH formation and ignition around top dead center (TDC). With ozone addition, methyl hydroperoxide (CH3OOH) becomes very important earlier in the compression stroke under these fuel-rich conditions. It is then later converted to CH2O and H2O2. Thus, ozone is a very effective additive not only for fuel-lean, but also for fuel-rich combustion. However, the mechanism differs between both regimes. Because less of the expensive additives are needed, ozone could help improving the economics of a polygeneration process with fuel-rich operated HCCI engines. 相似文献
Metallocenes are organometallic compounds with reversible redox profiles and tunable oxidation and reduction potentials, depending on the metal and substituents at the cyclopentadienyl rings. Metallocenes have been introduced in macromolecules to combine the redox‐activity with polymer properties. There are many examples of such hydrophobic polymer materials, but much fewer water‐soluble examples are found scattered across the polymer literature. However, in terms of drug delivery and other biological applications, water solubility is essential. For this very reason, all the synthetic routes to water‐soluble metallocene containing polymers are collected and discussed here. The focus is on neutral ferrocene‐ and ruthenocene‐containing and charged cobaltocenium‐containing macromolecules (i.e., symmetrical sandwich complexes). The synthetic protocols, self‐assembly behavior, and other benefits of the obtained materials are discussed.
Approximate analytical solutions of the Dirac equation are obtained for the Yukawa potential plus a tensor interaction with any κ-value for the cases having the Dirac equation pseudospin and spin symmetry. The potential describing tensor interaction has a Yukawa-like form. Closed forms of the energy eigenvalue equations and the spinor wave functions are computed by using the Nikiforov–Uvarov method. It is observed that the energy eigenvalue equations are consistent with the ones obtained before. Our numerical results are also listed to see the effect of the tensor interaction on the bound states. 相似文献