Experimental investigation and numerical simulation of the influence of resonator-length detuning on the output power,pulse duration and spectral width of a cw mode-locked picosecond optical parametric oscillator

We report on a cw mode-locked non-critically phase matched KTP optical parametric oscillator synchronously pumped by a picosecond Ti:Sapphire laser. High average signal output power of up to 950 mW over a large tuning range has been achieved. For this OPO the influence of resonator-length detuning on the output power, pulse duration and spectral bandwidth has been investigated. The measured data are in good agreement with the results of a numerical simulation using a split-step Fourier method which considers the group-velocity mismatch, the group-velocity dispersion and the self-phase modulation. The numerical simulation also describes the measured strong pump depletion and its influence on the OPO output and efficiency.     

Stability testing in an integrated scheme

ISO Guide 35 deals with RM stability issues and scrutinizes the evaluation of stability testing results under the assumption that either there is no trend at all (a rather rare situation), or any observed deterministic change is insignificant and thus can be neglected. However, market demands for reliable reference materials are obviously not limited to stable or at least seemingly stable materials. In many analytical applications, analytes and measurands under consideration are known, or at least suspected, to be unstable on time scales that may vary widely from measurand to measurand. The Federal Institute for Materials Research and Testing (BAM) has developed (and successfully uses) an integrated approach in its certification practice. The approach is based on an initial stability study and subsequent post-certification monitoring. Data evaluation is model-based and takes advantage of all information collected in the stability testing scheme(s). It thus allows one to deal with any kind of instability observed, to assess limiting time intervals at any stress condition in the range tested, to estimate a final expiry date for materials with detected instabilities or the maximum admissible re-testing interval for seemingly stable materials, and to assess maximum admissible stress loads during delivery of the material to the customer. The article describes (and exemplifies) typical study layout, the model selection, and the integrated data assessment.     

Conceptual continuity as a mode of understanding complex systems: Applications to the dynamics sociopolitical systems

In complex biological systems, entities that are conceptually distinct but empirically related—such as sunlight and plant growth or antigene and immune response—are being explicitly linked through the identification of highly specific uninterrupted interaction sequences that take place between their macromolecular system components. These uninterrupted sequences of causation include common elements that are shared by the empirically related but conceptually distinct entities. Through the identification of specific shared elements, “conceptual continuity” is established between these entities. Examples are introduced to suggest that in sociopolitical systems, an analogous conceptual continuity can be established between distinct sociopolitical entities. The identification of specific shared elements, essential for the well being of each of the entities, can play a significant role in resolving conflicts between those separated by seemingly insurmountable obstacles such as race or religion or ideology. © 2006 Wiley Periodicals, Inc. Complexity 11:20–24, 2006     

Realisation and metrological characterisation of thickness standards below 100 nm

High-accuracy film thickness measurements in the range below 100 nm can be made by various complex methods like spectral ellipsometry (SE), scanning force microscopy (SFM), grazing incidence X-ray reflectometry (GIXR), or X-ray fluorescence analysis (XRF). The measurement results achieved with these methods are based on different interactions between the film and the probe. A key question in nanotechnology is how to achieve consistent results on a level of uncertainty below one nanometre with different techniques.Two different types of thickness standards are realised. Metal film standards for X-ray techniques in the thickness range 10 to 50 nm are calibrated by GIXR with monochromatised synchrotron radiation of 8048 eV. The results obtained at four different facilities show excellent agreement. SiO₂ on Si standards for SE and SFM in the thickness range 6 to 1000 nm are calibrated by GIXR with monochromatised synchrotron radiation of 1841 eV and with a metrological SFM. Consistent results within the combined uncertainties are obtained with the two methods. Surfaces and interfaces of both types of standards are additionally investigated by transmission electron microscopy (TEM). PACS 61.10.Kw; 68.55.Jk; 06.20.Fn; 06.60.Mr; 07.79.Lh     

Efficient indirect electrochemical in-situ regeneration of nadh:electrochemically driven enzymatic reduction of pyruvate catalyzed by d-ldh

Using [Cp(Me)₅Rh(bipy)C1]C1 (1) as redox catalyst for the continous NADH regeneration it was possible to perform an electrochemically driven enzymatic reduction of pyruvate to D-lactate catalyzed by D-LDH at a rate of 5 turnovers per hour. This is by a factor of 20 faster than the best results obtained until now. Current yields of 50 to 70 % may be obtained.     

Behavior of iodododecane in nuclear fuel reprocessing

By simulation experiments with a 10^–5 mol/l solution of iodododecane labeled with¹³¹I in n-dodecane the influence of various materials and conditions, which are possible in nuclear fuel reprocessing, has been investigated. The formation of decomposition products was detected via HPLC with a radioactivity monitor. By means of²⁵²Cf plasma-desorption mass spectrometry (PDMS) the decomposition products were identified. It was found that a temperature of 100°C favored the formation of iodoalkanes with chain lengths of C₁ to C₁₁. The presence of TBP(tri-n-butyl-phosphate) accelerated the decomposition of iodododecane. In pure TBP only iodobutane was formed as a decomposition product.     

Spin Axioms in Different Geometries of Relativistic Continuum Physics

The 24 components of the relativistic spin tensor consist of 3 + 3 basic spin fields and 9 + 9 constitutive fields. Empirically only three basic spin fields and nine constitutive fields are known. This empirem can be expressed by two spin axioms, one of them denying purely relativistic spin fields, and the other one relating the three additional basic fields and the nine additional constitutive fields to the known (and measurable) ones. This identification by the spin axioms is material-independent and does not mix basic spin fields with constitutive properties. The approaches to the Weyssenhoff fluid and the Dirac-electron fluid found in literature are discussed with regard to these spin axioms. The conjecture is formulated, that another reduction from six to three basic spin fields which does not obey the spin axioms introduces special material properties by not allowed mixing of constitutive and basic fields.