Synthesis and Characterization of Hydrophobic Silica Aerogels Using Trimethylethoxysilane as a Co-Precursor

The hydrophobic property is one of the most important requirements for the long-term use of silica aerogels for transparent or translucent window insulation and opaque thermal insulating systems. Therefore, the present paper deals with the synthesis and characterization of hydrophobic silica aerogels using trimethylethoxysilane (TMES) as a co-precursor. Silica sol was prepared by keeping the molar ratio of tetramethoxysilane (TMOS) precursor, methanol (MeOH) solvent, water (H₂O) and ammonia (NH₄OH) catalyst constant at 1:12:4:3.7 × 10^–3 respectively throughout the experiments and the TMES/TMOS molar ratio (A) was varied from 0 to 2.35. The resulting silica alcogels were dried supercritically by high-temperature alcohol solvent extraction. Hydrophobicity of the aerogels was tested by measuring the percentage of water adsorbed by the aerogels after putting them directly on the surface of water under humid conditions. Alternately, the hydrophobicity was also tested by contact angle measurements. It was found that as the A value increased, the hydrophobicity of the aerogels increased but the optical transmission decreased from 93% to less than 5% in the visible range. The thermal stability of the aerogels was studied in the temperature range from 25 to 400°C. The hydrophobic nature of the aerogels was maintained up to a temperature of 300°C. The aerogels were characterized by infrared spectroscopy, optical transmittance, Scanning electron microscopy (SEM) and contact angle measurements. The results have been discussed by taking into account the hydrolysis and condensation mechanisms.     

Electrical and humidity characterization of m-NA doped Au/PVA nanocomposites

The Meta-Nitroaniline (m-NA) doped (by varying weight percentage (wt. %)) gold/polyvinyl alcohol (Au/PVA) nanocomposites were synthesized using gold salt and hydrazine hydrate (HH) by in situ process. The composite was coated on ceramic rods having two end electrodes by drop casting method for studying their electrical behavior at different relative humidity (RH) levels, ranging from 4 to 95% RH at room temperature. The optimized wt. % was used to prepare coatings of various thicknesses (20-40 μm) of the films. As the humidity decreases, the resistance increases. The low humidity sensing characteristic can be tailored by varying wt. % of m-NA and thicknesses of the nanocomposite films. The resistive-humidity sensor shows two regions of sensitivity having highest sensitivity for lower RH. The sensor response and recovery time is about 6-10 s and 52 s respectively. The dynamic range of variation of the resistance allows a promising use of the films as a humidity sensor. The material was characterized by X-ray diffraction (XRD) and impedance spectroscopy at 60% RH.     

Uncapped silver nanoparticles synthesized by DC arc thermal plasma technique for conductor paste formulation

Uncapped silver nanoparticles were synthesized by DC arc thermal plasma technique. The synthesized nanoparticles were structurally cubic and showed wide particle size variation (between 20–150 nm). Thick film paste formulated from such uncapped silver nanoparticles was screen-printed on alumina substrates and the resultant ‘green’ films were fired at different firing temperatures. The films fired at 600 °C revealed better microstructure properties and also yielded the lowest value of sheet resistance in comparison to those corresponding to conventional peak firing temperature of 850 °C. Our findings directly support the role of silver nanoparticles in substantially depressing the operative peak firing temperature involved in traditional conductor thick films technology.     

Preparation, characterization and non-linear optical properties of pristine m-nitroaniline (m-NA) and its recycled polystyrene (Re-PS) coated single crystals

Meta-nitroaniline (m-NA) is one of the organic single crystals extensively studied due to its high non-linear effect. m-NA is also known to exhibit comparable or even better non-linear optical (NLO) properties than known inorganic materials. In this paper, we report development of m-NA single crystals by solution growth technique using different solvent systems. The size of the single crystal varies depending on solvent. The highest average crystal size acquired was 10 mm×5 mm×5 mm using methyl ethyl ketone and acetone as solvent. These single crystals were characterized using various physico-chemical techniques such as XRD and scanning electron microscopy (SEM). The developed crystals were subsequently coated with recycled polystyrene (Re-PS) (1, 2, 5 and 10 wt% concentrations) to study the effect of polymer coating on the second harmonic generation (SHG) properties of the single crystals. The purpose of polymer coating on m-NA single crystal is to improve surface morphology of crystal (i.e. it makes surface smooth) and to enhance power handling capacity for pulse laser of a crystal which, in turn, improves the SHG intensity. The optimum percentage of coating was determined for the m-NA single crystals obtained from different solvent systems. Furthermore, the polymer coating also plays key role in preventing the degradation of the m-NA crystal (well-known as highly sublime material) and ultimately increasing the shelf life of the crystal for its device application.     

Superhydrophobic silica aerogels based on methyltrimethoxysilane precursor

The experimental results on the synthesis and physicochemical properties of superhydrophobic silica aerogels, with the highest ever obtained contact angle (173°), using methyltrimethoxysilane (MTMS) precursor, methanol (MeOH) solvent and ammonium hydroxide (NH₄OH) catalyst, are reported. The molar ratios of NH₄OH/MTMS (N), H₂O/MTMS (H) and MeOH/MTMS (M) were varied from 4.25 × 10⁻² to 3.5 × 10⁻¹, 2 to 10 and 1.75 to 17, respectively. It has been found that the gelation time decreases with increase in N and H values and it increases with increase in M values. The bulk density of the aerogels was found to decrease with increase in N, H and M values. It has been observed that the volume shrinkage increases with decrease in N and H values and increases with M values. In the case of catalyst concentration variation, the contact angle (θ) increases slightly from 159° to 167° with increase in N values. On the other hand, in the case of H₂O and MeOH variations, the θ first increases from 162° and 160° up to the values of 173° and 167° and then decreases to 160° and 159° with increase in H and M values, respectively. All the MTMS aerogels are opaque to the visible light. The aerogels retain their hydrophobicity up to a temperature of 480 ° C. The thermal conductivity of the aerogels was found to be around 0.095 W/m K except for the aerogels with higher bulk density (>0.3 g/cm³, at a lower H value of 2) whose thermal conductivity was around 0.109 W/m K. The aerogels have been characterized by Fourier transform infrared spectra (FTIR), thermogravimetric and differential thermal analyses (TGA-DTA) and scanning electron microscopy (SEM) techniques. The results have been discussed by taking into account the hydrolysis and condensation reactions and SEM observations.     

Influence of the deposition parameters on the microstructure and opto-electrical properties of hydrogenated nanocrystalline silicon films by HW-CVD

Hydrogenated nanocrystalline silicon (nc-Si:H) films were prepared at high deposition rates (> 13 Å/s) from pure silane without hydrogen dilution by hot wire deposition method by varying filament-to-substrate distance (d_s-f). In this study we have systematically and carefully investigated the effect of filament-to-substrate distance on structural, optical and electrical properties of the Si:H films. A variety of characterization techniques, including Raman spectroscopy, low angle X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, Atomic Force Microscopy (AFM), Field Emission Scanning Electron Microscopy (FE-SEM), UV-Visible-NIR spectroscopy and electrical dark and photoconductivity measurement were used to characterize these films. Films deposited at d_s-f > 5 cm are amorphous while those deposited at d_s-f < 5 cm are biphasic; a crystalline phase and an amorphous phase with nano-sized crystallites embedded in it. Low angle X-ray diffraction analysis showed that the crystallites in the films have preferential orientation along (111) directions. Decrease in d_s-f, the crystallinity and crystalline size increases whereas hydrogen bonding shifts from mono-hydride (SiH) to di-hydride (SiH₂) and poly-hydride (SiH₂)_n complexes. The band gaps of nc-Si:H films (~ 1.9-2.0 eV) are high compared to the a-Si:H films, while hydrogen content remains < 10 at.%. We attribute the high band gap to the quantum size effect. A correlation between electrical and structural properties has been established. Finally, from the present study it has been concluded that the filament-to-substrate distance is a key process parameter to induce the crystallinity in the films by hot wire method. The ease of depositing films with variable crystallite size and its volume fraction, and tunable band gap is useful for fabrication of tandem/micro-morph solar cells.     

The Effect of Zinc Ions on the Fluorescence Spectra of (Ln,Zn)of:Eu3+(Ln=Y,La and Gd) Powder Phosphors

This research note reports the fluorescence properties of Eu³⁺-doped in three sets of (Y-Zn, La-Zn and Gd-Zn) oxy fluoride powder phosphors. on excitation with a UV-source, these phosphors have displayed orangish-red color and for which the chromaticity coordinates ([Xbar], [Ybar] have been computed. the relative fluorescence intensity ratios (R) for the different measured emission transitions have been evaluated in order to examine the effect of substitution of zinc ions in the host matrix on the fluorescence behavior. Scanning electron microscopy studies have also been performed to investigate the average grain size of the synthesized phosphor material.