Column preconcentration of gold by adsorbing AuCl<Stack><Subscript>4</Subscript><Superscript>−</Superscript></Stack> onto methyltrioctyl ammonium chloride–naphthalene and subsequent atomic absorption spectrometric determination

A sensitive, selective and simple preconcentration method for ultra-trace gold determination has been developed that uses naphthalene–methyltrioctyl ammonium chloride (Aliquat 336s) as an adsorbent. Gold, in the form of AuCl₄^–, was retained by the adsorbent in the column at a flow rate of 1 ml min^–1. After filtration, the solid mass consisting of the gold complex and naphthalene was dissolved out of the column with 5 ml of N,N-dimethylformamide (DMF), and the metal was then determined by atomic absorption spectrometry. In the initial solution, the calibration graph of absorbance versus gold concentration was found to be linear in the range 0.5–150 ng ml^–1 Au(III) with r=0.997 (n =9), and the 3 s detection limit was 0.428 ng ml^–1. The relative standard deviation for eight replicate measurements of 20 g of gold was 2.14%. Preconcentration factors of 390 and 650 were achieved using 5 ml and 3 ml of DMF, respectively. The proposed method was successfully applied to the determination of gold in wastewater, processed pool water, slurry pool water, and raw well-water from the Moteh gold mine, and synthetic samples.     

Dipyrromethane as a new organic reagent for the synthesis of gold nanoparticles: preparation and application

Condensation reaction of several ketones with pyrrole in the presence of ferric hydrogen sulfate as a green homogenous acidic catalyst furnished the corresponding pure dipyrromethanes in good yields. Gold nanoparticles were produced through reduction of HAuCl₄ with substituted dipyrromethanes as new reducing agents at room temperature with the exclusion of any capping agent or surfactant. Gold nanoparticles were characterized by transmission electron microscopy, scanning electron microscopy, XRD and UV–visible absorption spectroscopic measurements. It is proposed that in situ formed oxidative products of dipyrromethane, such as polydipyrromethane could serve effectively as a capping agent to preferably adsorb the {111} facets of gold crystals during the reduction process, which leads to the formation of gold nanoparticles.     

Air‐assisted liquid–liquid extraction coupled with dispersive liquid–liquid microextraction and a drying step for extraction and preconcentration of some phthalate esters from edible oils prior to their determination by GC

In this work, a new, cheap, simple, fast, and low organic solvent consuming procedure is proposed for isolation, enrichment, and gas chromatographic determination of some phthalate esters in edible oils. The method is based on a combination of air‐assisted liquid–liquid extraction and dispersive liquid–liquid microextraction followed by a drying step under N₂ gas. Several experimental parameters affecting both extraction and preconcentration steps were investigated and optimized. Under the optimum conditions for the proposed method, wide linear ranges (0.05–800 μg/L) and low detection limits (0.007–0.023 μg/L) were observed. The ranges of enrichment factors and extraction recoveries were 68–340 and 14–68%, respectively. Eventually, the target analytes were successfully determined in different edible oils using the proposed method.     

Highly stable copper/carbon dot nanofluid

Copper/carbon dot nanohybrids (Cu/CD NHs) were prepared via a facile precipitation method through a disproportionation reaction. The surface characterization was performed by various techniques such as XRD, FTIR and TEM. Then, water-based nanofluids composed of Cu/CD NHs at 0.1 and 0.5 mass% were prepared, and their thermo-physical properties including thermal conductivity, viscosity, density and specific heat were evaluated at various temperatures. The water-based Cu/CD nanofluid demonstrated to be a potential heat transfer fluid with a high stability. It was found that the thermal conductivity can be enhanced by increasing the nanoparticle concentration and temperature. Almost 1.25-fold increase in thermal conductivity has been achieved by raising the temperature up to 50 °C and at the concentration of 0.5 mass%. The heat capacity was found to increase with increasing concentration. Moreover, by increasing temperature the density and viscosity of the as-prepared nanofluid decreased, whereas the heat capacity showed an increasing trend.     

Flotation-assisted dispersive liquid–liquid microextraction method for preconcentration and determination of trace amounts of cobalt: Orthogonal array design

A simple, rapid, and efficient flotation-assisted dispersive liquid–liquid microextraction method was developed for preconcentration of trace amount of cobalt(II) ions. In this technique, a mixture of toluene and methanol (20: 80, v/v) was injected through the septum in the bottom of a narrow-bore tube containing cobalt solution. Afterwards, the fine droplets of extraction solvent were formed and cobalt (as 1-nitroso-2- naphtol complex) was collected on the surface of solution by aeration. The effect of different variables on the extraction efficiency of cobalt such as pH of solution, ligand concentration and injection volume was investigated using orthogonal array design. At optimum conditions, the calibration curve was linear over the range of 10–1000 μg/L. The detection limit, relative standard deviation and enrichment factor were 3 μg/L, 3.9% (n = 10) and 120, respectively. The developed method was successfully applied to the determination of cobalt in water and drug samples.     

A very efficent column for the separation of 60 volatile organochlorine priority pollutants and for other environmental problems

Summary The complete separation of the sixty volatile organochlorine (VOC) priority pollutants has been achieved by coupling two different liquid-modified adsorption chromatography columns. Two temperature programs were used to obtain the complete separation in a relatively short analysis time. Detection was by FID alone     

Narrow bore silica capillary columns for liquid-modified adsorption gas chromatography

Summary The preparation of narrow bore capillary columns for liquid-modified adsorption chromatography is described, and the advantages of this technique for rapid analysis of complex mixtures are discussed.Several applications to the analysis of complex mixtures are reported, and the possibility of on-column injection is demonstrated.     

Synthesis and characterization of new derivatives of bis(1,4-diazepinium) salts and bis(γ-substituted pentamethine cyanine(dyes using vinamidinium salt

The preparation of several bis(1,4-diazepinium) salts from the reaction of three 1,2-diamines with a bis(vinamidinium) salt is described. Bis(γ-substituted pentamethine cyanine(dyes are also prepared from the reaction of vinamidinium salt with 1,2-dimethylquinolinium perchlorate and 1,2,3,3-tetramethyl-3H-indolium perchlorate. Data from elemental analyzes, IR, ¹H-NMR, ¹³C-NMR, and mass spectra (MS) confirm the molecular structure of the obtained products.     

New GC quartz-lined aluminum capillary columns coated with graphitized carbon black modified by liquid phases

Summary Fused silica is by far the best material for most kinds of GC capillary columns but in some particular conditions, when a drastic or alkaline treatment is required, this material and especially the polyimide protector layer do not possess high chemical resistance and could easily break down. In order to overcome this disadvantage, in this paper, we present a new type of column — a quartz-lined aluminum capillary coated with graphitized carbon black modified by liquid phases by using a new coating procedure. With the above material a capillary column for amine analysis, and another for the analysis of VOCs and oil products are obtained. Some characteristic applications of both columns are reported.