金属管(杆)横驻波演示实验

对两端自由金属管(杆)弯曲振动实验进行了分析,对观察到的现象给出了相应的解释.     

φ型风力机空气动力学特性研究

本文采用均匀多流管模型和多流管模型,建立了基于Troposkien曲线的Φ型垂直轴风力机气动性能的计算方法和程序。在多流管模型中加入了附加阻力系数修正和动态失速修正,提高了计算精度。分析了流管数目对流管模型计算结果,以及实度和高径比对Φ型风力机空气动力学特性的影响。     

Flexural vibration analyses of piezoelectric ceramic tubes with mass loads in ultrasonic actuators

Based on Timoshenko beam model, a theoretical model of radially polarized piezoelectric ceramic tubes is investigated. In the model, the piezoelectric effects are considered, and the shear correction factor is introduced which reveals effects of the size of the cross-section and Poisson’s ratio. Based on the model, the particular attentions are devoted to effects of the boundary conditions at two ends on flexural resonance frequencies of the piezoelectric ceramic tubes. Changing the sizes of the tubes and the mass loads at both free ends, the variations of the flexural resonance frequencies of free–free piezoelectric ceramic tubes are calculated theoretically. Besides, the flexural resonance frequencies of the piezoelectric ceramic tube cantilevers with mass loads at one free end are also investigated theoretically. To verify accuracy of the theoretical mode, the flexural resonance frequencies for different lengths of the piezoelectric ceramic tubes and different loaded masses are measured experimentally. The theoretical results agree well with the experimental measurement, which demonstrates that the model is accurate for analyzing the flexural resonance frequencies of the piezoelectric ceramic tubes with mass loads.     

舰载导弹振动环境状态实时监测系统设计

为了全面监测舰上导弹贮存的振动环境,设计了对舰艇横摇、纵摇和升沉条件下的加速度信号实时监测系统;该系统采用一体化、模块化设计的思想,应用堆栈式结构总线PC104,提高了系统的便携性、可靠性;采用两种供电方式提高了系统适应性;文章详细阐述了硬件系统和软件系统的设计,并重点对数据采集存储和数据显示功能实现进行了论述;在1 000 Hz采样频率的实验条件下,采集数据准确可靠,精确度为99.75%,达到了系统设计的要求。     

The Morphology and Mechanical Properties of Isotactic Polypropylene Injection-Molded Samples with the Presence of β-Nucleation Agent and Periodical Shear Field

The pressure vibration injection molding (PVIM) method was used to prepare β-nucleated isotactic polypropylene samples (PVIM β-iPP samples); a relatively low, periodical shear was imposed on the polymer melt in the mold at the filling and packing stages. The crystal structures and crystal orientation of the PVIM β-iPP samples were investigated by polarizing light microscopy (PLM), scanning electron microscopy (SEM), and synchrotron two-dimensional wide-angle X-ray diffraction (2D-WAXD). The PLM observations indicated that a cylindrite layer, rather than the transition layer, was found in PVIM β-iPP samples, which is different from the conventional injection-molded (CIM) samples. In addition, the thickness of the oriented layer of the PVIM samples was obviously greater than that of the CIM samples. The SEM observations demonstrated that a large amount of shish-kebab structures appeared in the shear layer of the PVIM β-iPP samples; at the same time, numerous β-spherulites were formed in the core layer. The 2D-WAXD data indicated that orientation homogeneity, to some degree, could be obtained by the periodical shear during PVIM. As a result, the above-mentioned morphology of the PVIM β-iPP samples leads to potentially useful prominent reinforcement and toughening of the material.     

A theoretical and numerical evaluation of the steady-state burning rate of vertically oriented PMMA slabs

The steady state burning rate of vertically oriented slabs of poly-methyl-methacrylate (PMMA) is numerically investigated. Model predictions are compared with measurements and results of the laminar boundary layer (LBL) theory. The numerical model provides a solution of the Favre-averaged Navier–Stokes equations coupled with sub-models for turbulence, combustion, soot production and radiation. The modelling of condensed phase processes is based on the one-dimensional heat transfer equation and pyrolysis is treated as a phase change using the latent heat approach. Results show that the pyrolysing region can be divided into three regions. In the laminar part of the flow (Gr _x < 4.3 × 10⁷), the predicted normalised burning rate, [mdot]″ _p x/μ_∞, is a power-law function of Gr _x with an exponent close to that of the LBL theory, surface re-radiation being the primary source of discrepancies. From the LBL theory for free flow, it is demonstrated that the local burning rate is inversely proportional to the shear velocity gradient. This is globally confirmed by numerical model results. At Gr _x = 4.3 × 10⁷ the change in slope of the burning rate observed experimentally, which indicates the end of the laminar flow region, is reproduced numerically. From Gr _x = 2.5 × 10⁹ model results show that the surface mass flux of pyrolyzate increases with x, in agreement with experimental data in literature.     

The resonant secondary emission of the F center in alkali halides

The secondary radiation after resonant excitation of F center and its linear polarization P correlated to the polarization of resonant light have been measured for five alkali halides at low temperatures. In KC1, the spectrum of P over the whole Stokes region is divided into three successive regions, the depolarization range at the one-phonon Raman scattering, the near plateau range, and the depolarization range down to vanishing. The former two have common relevance to resonant energy and symmetries of coupled phonons. These relevances are interpreted adopting a configuration coordinate model for 2s- and 2p-like excited states.     

驻波实验中一个经常出现的错误

对驻波演示实验中出现的立体驻波的原因及特点进行分析,并提出改进实验的建议.     

弹簧耦合摆小振动的简正模与简正频率

将耦合摆弹簧作为弹性均匀杆,导出了对称简正模与反对称简正模的本征方程,给出各角频率值的近似式,并进行了讨论。     

带隙可调各向同性蛋白石光子晶体的制备与研究

用旋涂法将聚苯乙烯微球组装成光子晶体,研究了此光子晶体的特点,并分析了在单一微球粒径下旋涂参数对光子带隙的影响.结果表明:旋涂法制备的光子晶体具有各向同性特点,其光子带隙由旋涂参数决定.光子晶体的反射波段取决于乳液中微球的质量分数,而反射强度取决于旋涂层数.因此,在设计光子晶体时,可以根据需要,通过微球的质量分数和旋涂...