Sensitivity analysis of an optimized bar-spring model with hill-top branching

Summary Characteristics of optimal solutions under nonlinear buckling constraints are investigated by using a bar-spring model. It is demonstrated that optimization under buckling constraints of a symmetric system often leads to a structure with hill-top branching, where a limit point and bifurcation points coincide. A general formulation is derived for imperfection sensitivity of the critical load factor corresponding to a hill-top branching point. It is shown that the critical load is not imperfection-sensitive even for the case where an asymmetric bifurcation point exists at the limit point.     

Viscoelastic behavior of polypropylene/nitrile rubber thermoplastic elastomer blends: Application of Kerner's models for reactively compatibilized and dynamically vulcanized systems

The viscoelastic properties of binary blends of nitrile rubber (NBR) and isotactic polypropylene (PP) of different compositions have been calculated with mean‐field theories developed by Kerner. The phase morphology and geometry have been assumed, and experimental data for the component polymers over a wide temperature range have been used. Hashin's elastic–viscoelastic analogy principle is used in applying Kerner's theory of elastic systems for viscoelastic materials, namely, polymer blends. The two theoretical models used are the discrete particle model (which assumes one component as dispersed inclusions in the matrix of the other) and the polyaggregate model (in which no matrix phase but a cocontinuous structure of the two is postulated). A solution method for the coupled equations of the polyaggregate model, considering Poisson's ratio as a complex parameter, is deduced. The viscoelastic properties are determined in terms of the small‐strain dynamic storage modulus and loss tangent with a Rheovibron DDV viscoelastometer for the blends and the component polymers. Theoretical calculations are compared with the experimental small‐strain dynamic mechanical properties of the blends and their morphological characterizations. Predictions are also compared with the experimental mechanical properties of compatibilized and dynamically cured 70/30 PP/NBR blends. The results computed with the discrete particle model with PP as the matrix compare well with the experimental results for 30/70, 70/30, and 50/50 PP/NBR blends. For 70/30 and 50/50 blends, these predictions are supported by scanning electron microscopy (SEM) investigations. However, for 30/70 blends, the predictions are not in agreement with SEM results, which reveal a cocontinuous blend of the two. Predictions of the discrete particle model are poor with NBR as the matrix for all three volume fractions. A closer agreement of the predicted results for a 70/30 PP/NBR blend and the properties of a 1% maleic anhydride modified PP or 3% phenolic‐modified PP compatibilized 70/30 PP/NBR blend in the lower temperature zone has been observed. This may be explained by improved interfacial adhesion and stable phase morphology. A mixed‐cure dynamically vulcanized system gave a better agreement with the predictions with PP as the matrix than the peroxide, sulfur, and unvulcanized systems. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1417–1432, 2004     

On practical metrology and chemical analysis: etalons and traceability systems

 National measurement systems are infrastructures to ensure, for each nation, a consistent and internationally recognised basis for measurement. Such complex systems have historical, technical, legal, organisational and institutional aspects to connect scientific metrology with practical measurements. Underlying any valid measurement is a chain of comparisons linking the measurement to an accepted standard. The ways the links are forged and the etalons (measurement standards) to which they connect are defining characteristics of all measurement systems. This is often referred to as traceability which aims at basing measurements in common measurement units – a key issue for the integration of quantitative chemical analysis with the evolving physical and engineering measurement systems. Adequate traceability and metrological control make possible new technical capabilities and new levels of quality assurance and confidence by users in the accuracy and integrity of quantitative analytical results. Traceability for chemical measurements is difficult to achieve and harder to demonstrate. The supply of appropriate etalons is critical to the development of metrology systems for chemical analysis. An approach is suggested that involves the development of networks of specialised reference laboratories able to make matrix-independent reference measurements on submitted samples, which may then be used as reference materials by an originating laboratory using its practical measurement procedures. Received: 31 July 1995 Accepted: 19 August 1995     

Butyltins in california river and lake marina waters

Butyltins were analyzed in waters from California river and lake marinas and were detected at the part per trillion (ppt) level in most locations. The tributyltin:dibutyltin (TBT/DBT) ratios in the fresh waters were similar to those in their saline counterparts indicating like rates of degradation in the two salinity regimes.     

Determination of tributyltin oxide in coastal marine sediments and mussels by electrothermal atomic absorption spectrometry

We have devised a new method for bis(tributyltin)oxide (TBTO) determination in marine sediments and mussels. This technique involves an n-hexane/methylene chloride mixture extraction and extract purification with a sodium hydroxide wash in order to eliminate interfering compounds. TBTO is then extracted again by nitric acid and converted into an inorganic tin species; the analysis has been effected using Zeeman graphite furnace-atomic absorption spectrophotometry. The method detection limit for the matrices examined is 0.004 μg TBTO g^?1 (wet weight) and is sufficient for the analysis in real samples. The percentage recovery of TBTO from sediments and mussels samples is higher than 85% and 95% respectively. This method has been applied to TBTO level determination in sediments and mussels (Mytilus galloprovincialis) sampled in the harbour area in Taranto, where mussel culture activities are much developed; the TBTO levels obtained in sediments and mussels were in the range 15-47 ng g^?1 (wet weight) and 11-30 ng g^?1 (wet weight) respectively. Such values are comparable with those found in other harbour areas in the Mediterranean Sea.     

Numerical analysis of time-dependent Boussinesq models

In this paper we analyse numerical models for time-dependent Boussinesq equations. These equations arise when so-called Boussinesq terms are introduced into the shallow water equations. We use the Boussinesq terms proposed by Katapodes and Dingemans. These terms generalize the constant depth terms given by Broer. The shallow water equations are discretized by using fourth-order finite difference formulae for the space derivatives and a fourth-order explicit time integrator. The effect on the stability and accuracy of various discrete Boussinesq terms is investigated. Numerical experiments are presented in the case of a fourth-order Runge-Kutta time integrator.     

A numerical study of an unsteady laminar flow in a doubly constricted 3D vessel

Unsteady flow dynamics in doubly constricted 3D vessels have been investigated under pulsatile flow conditions for a full cycle of period T. The coupled non‐linear partial differential equations governing the mass and momentum of a viscous incompressible fluid has been numerically analyzed by a time accurate Finite Volume Scheme in an implicit Euler time marching setting. Roe's flux difference splitting of non‐linear terms and the pseudo‐compressibility technique employed in the current numerical scheme makes it robust both in space and time. Computational experiments are carried out to assess the influence of Reynolds' number and the spacing between two mild constrictions on the pressure drop across the constrictions. The study reveals that the pressure drop across a series of mild constrictions can get physiologically critical and is also found to be sensitive both to the spacing between the constrictions and the oscillatory nature of the inflow profile. The flow separation zone on the downstream constriction is seen to detach from the diverging wall of the constriction leading to vortex shedding with 3D features earlier than that on the wall in the spacing between the two constrictions. Copyright © 2002 John Wiley & Sons, Ltd.     

Amending cultures of selenium-resistant bacteria with dimethyl selenone

A possible biological intermediate in the reduction and methylation of selenium oxyanions, dimethyl selenone, was synthesized, and the first experiments involving the amendment of selenium resistant bacterial cultures with this compound are reported. The amount of volatile, reduced selenium-containing species released from these cultures into the headspace is significantly more than that produced in analogous experiments involving sodium selenate amended cultures. Dimethyl selenone is reduced in the presence of dimethyl sulfide and dimethyl disulfide in a complex growth medium, trypticase soy broth with 0.1% nitrate. This reduction occurs whether or not the reduced sulfur compounds are biologically produced.     

Towards understanding the increase in strength of thermotropic polyesters with heat treatment

Thermotropic copolyester fibers of oxynaphthoate and oxybenzoate have been subjected to conditions that promote solid-state polymerization as well as annealing. The annealing process causes the crystals to perfect with a simultaneous increase in heat of fusion and melting temperature. Solid-state polymerization, a reaction rate-controlled process, causes the polymer viscosity average molecular weight to increase by chain extension from about 14,000 g/mole to more than 87,000 g/mole with a simultaneous impressive increase in tenacity from about 10 g/d (1.2 GPa) to almost 30 g/d (3.7 GPa). To understand the changes in mechanical properties, we have modeled the fiber structure as short rod-like molecules poorly bonded to a continuous matrix of parallel molecules. Lengthening of the reinforcing molecules facilitates better transfer of load from matrix to molecules, resulting in higher tenacity fibers. © 1994 John Wiley & Sons, Inc.