正电子产生靶上初级电子束半径的最小化研究

为获得尽可能高的正电子(e⁺)产额,严格控制初级电子(e^－)束在e⁺产生靶上的束半径是至关重要的.首先分析了使e^－束半径增大的各因素和对这些因素的制约;然后以北京正负电子对撞机(BEPC)的正电子源为例,给出了束半径的实测值和计算值的比较,以具体说明这些因素的影响;最后讨论了北京正负电子对撞机二期工程(BEPC-Ⅱ)的相应优化设计研究,提出了获得靶上最小束半径的若干途径.     

Low-lying states of 6He studied via the 6Li(t,3He)6He reaction

We present the recent experimental results on the ⁶He structure studied by the ⁶Li(t, ³He)⁶He reaction at 336 MeV. Above the conspicuous peaks for ground and first excited states for ⁶He, we have observed a broad structures at E _x∼ 5 MeV, and E _x∼ 15 MeV. The angular distribution of this structure exhibits the dominance of a ΔL = 1 transition, indicating the existence of intruder dipole states at low excitation energies in ⁶He. A slight admixture of positive-parity states in this structure has been indicated as well. Received: 1 May 2001 / Accepted: 4 December 2001     

Influence of SiO2 in SiCp on the microstructure and impact strength of Al/SiCp composites fabricated by pressureless infiltration

The effect of SiO₂ in SiC_p and the following processing parameters on the microstructure and impact strength of Al/SiC_p composites fabricated by pressureless infiltration was investigated: Mg content in the aluminum alloy, SiC particle size, and holding time. Preforms of SiC_p in the form of rectangular bars (10 × 1 × 1 cm) were infiltrated at 1150°C in an argon→nitrogen atmosphere for 45 and 60 min by utilizing two aluminum alloys (Al-6 Mg-11 Si and Al-9 Mg-11 Si, wt.%). The results obtained show that the presence of SiO₂ in SiC affects the microstructure and impact strength of the composites significantly. When Al₄C₃ is formed, the impact strength decreases. However, a high proportion of SiC to SiO₂ limits the formation of the unwanted Al₄C₃ phase in the composites. Also, a higher content of Mg in the Al alloy lowers the residual porosity and, consequently, increases the composite strength. The impact strength grows with decrease in SiC particle size and increases considerably when the residual porosity is less than 1%. Russian translation published in Mekhanika Kompozitnykh Materialov, Vol. 42, No. 3, pp. 401–418, May–June, 2006.     

新型噻吩基取代卟啉的合成及其荧光光谱研究

合成了两种新型噻吩基卟啉－5，15－二（2－噻吩基）－2，8，12，18－四乙基－3，7，13，17－四甲基卟啉7a（45．1％）和5，15－二（2－联噻吩基）－2，8，12，18－四乙基－3，7，13，17－四甲基卟啉7b(61.2%),并研究了它们的光谱性质，其中荧光光谱的最大发射峰蜂都在631nm处，量子产率分别为4．1％（7a)和1．4％（7b)。     

谈青少年业余运动员的力量训练

对青少年业余运动员力量训练的作用、影响因素和训练方法进行探讨,提出力量训练要针对青少年的身心特点和专项要求,长期坚持,重视质量,其效果取决于计划的系统性和训练方法的选择。     

某库岸滑坡稳定分析及治理措施研究

从地质条件出发,详细分析了滑坡的成因,以大型的岩土工程数值分析软件(ADINA)为研究手段,建立有限元计算模型,用强度折减的方法分析了滑坡体在初始工况、蓄水工况、暴雨工况、水位骤降工况和地震工况下的稳定情况,根据滑坡的失稳情况,在综合考虑的基础上,提出了削坡减载和地表排水相结合的治理措施,计算结果表明,治理措施是可行的,研究结果对设计和施工具有较大的参考价值.     

影响DPF焦点装置中子稳定性的因素和改进措施

简要叙述了稠密等离子体聚焦装置作为中子发生器的工作原理，对影响稠密等离子体聚焦装置放电出中子产额及其稳定性的一些因素和改进措施进行了简单讨论．通过使用不同电极形状的场畸变开关很好地提高了焦点装置的运行，使装置输出中子的起伏得到明显的改善．通过对腔内电极的清洁，在不更换气体的条件下，聚焦装置放电出中子产额稳定.The principle of dense plasma focus(DPF) as neutron generator has been investigated in this paper. We have stated briefly some factors that mainly influnce the DPF s neutron yield and some methods improving the stability of neutron yields on the dense plasma focus. It is showed that the fluctuation of DPF output neutron becomes smaller by using different types of field-distortion elements. Over 100 consecutive shots without purging the test gas the neutron yields has no obvious change.     

A study on anisotropy of L2 to L3 Coster-Kronig transition (f23) for Th and U elements

The Coster-Kronig transition, f₂₃, was determined using differential fluorescence cross sections of L_l X-ray for Th and U. The targets were irradiated an Am-241 radioisotope at the different incident angle. The L_l X-rays were counted with a Si (Li) detector at the different scattering angle varying from 60° to 90° at 10° intervals. For each angle, the Coster-Kronig transition probability, f₂₃, was found. An obtained Coster-Kronig transition probability value was fitted versus emission angle. According to present results we can say that the Coster-Kronig transition probability, f₂₃, shows isotropic distribution.     

Liminf results on the increments of an (N,d)-Gaussian process

We establish some liminf theorems on the increments of a (N,d)-Gaussian process with the usual Euclidean norm, via estimating upper bounds of large deviation probabilities on the suprema of the (N,d)-Gaussian process. This revised version was published online in June 2006 with corrections to the Cover Date.     

Load-Carrying Capacity of Circular Plates Made of a Fiber-Reinforced Composite

The load-carrying capacity of circular plates made of a fiber-reinforced composite and loaded with axisymmetric transverse forces under axisymmetric boundary conditions is investigated. The plates can be freely supported or clamped along their contour. To the known yield condition used, in the plane of main bending moments, there correspond irregular hexagons, which depend on the mechanical properties of composite constituents and some characteristic geometrical parameters. It is shown that, depending on the ratio of ultimate radial and circumferential bending moments, in the plastic state, the circular plates (the central part of the clamped plates) take the form of a cone or a frustum of cone. For each of the cases, the limit load is found, which is a function of the above-mentioned mechanical parameters. The statically allowable fields of bending moments and the corresponding allowable fields of deflection rates are determined. The solutions found are exact. Special cases for the freely supported plates are analyzed, and the results obtained are presented in the form of graphs.__________Translated from Mekhanika Kompozitnykh Materialov, Vol. 41, No. 2, pp. 177–192, March–April, 2005.