PTC热敏电阻器的电阻温度特性及应用

本文从半导体陶瓷PTC热敏电阻器入手，讨论了该热敏材料的电阻温度特性，给出了PTC热敏电阻器的测量结果和应用范围。     

CO2气体保护堆焊榨辊轴的组织分析

对CO2气体保护堆焊修复榨辊轴的组织性能进行分析，发现用此方法修复的榨辊轴表面有索氏体组织，所以既保持原有的强度和韧性又增加了表面的抗磨性，是目前修复榨辊轴最行之有效的方法之一。     

化学镍磷镀层微动磨损力学分析及应用

对化学镍磷镀层在微动磨损过程中的应力强度和分布作了详细分析，并进一步用位错理论对微动磨损破坏进行了讨论．根据理论分析结果，解释了镍磷镀层的耐磨性，提出了对镀层厚度的合理要求．     

用T-Ω法分析发电机转子三维涡流场

本文用位对Ｔ－Ω，分析导体间有接触电阻的发电机转子三维负序涡流场。文中讨论了：位对及其规范的选择、位对边值问题解的唯一性，提出了用Ｄ－Ｑ轴脉振电磁场迭加计算旋转电磁场的方法，还提出“预消去法”计算方法。     

锌钴合金及其耐蚀性的电化学研究

采用线性电位扫描、极化电阻、交流阻抗等实验方法，研究弱酸性氯化钠电解液中锌－钴共沉积及其耐蚀性．实验表明：镀层的钴含量随着镀液的钴含量和电流密度的增加而增加．在电解液含钴２．５ｇ／Ｌ左右，电流密度１．５～２．５Ａ／ｄｍ２，ｐＨ值５．０～５．６，温度范围２０—３０℃的条件下镀层的极化电阻Ｒｐ比较大。镀层的腐蚀电化学行为说明：镀层腐蚀产物的阻挡作用提高了锌钴微合金镀层的耐蚀性．在本实验条件下，在弱酸性氯化钠溶液中，锌—钴共沉积属于异常共沉积．     

Optical studies of local flow behaviour of a non-Newtonian fluid inside a porous medium

In this study the local flow of a polymeric solution inside a porous medium is studied visually. While the flow is quite uniform for low volume flow rates it shows pronounced nonuniformity for higher volume flow rates. That is to say, only certain preferred passages are taken and these passages change in time (they fluctuate). This flow irregularity is the reason for increased resistance. Received: 28 April 1997 Accepted: 30 December 1997     

半桥逆变式功率VMOSFET超声电发生器的研制

本文介绍了一种用于超声波电火花复合加工的超声发生器，它以功率ＶＭＯＳ场效应管作开关元件，以单片集成电路ＴＬ４９４作为信号源控制核心。发在具有工作稳定可行以的特点。     

空气粘滞阻尼对g的影响

在气垫导轨上测重力加速度时,空气粘滞阻尼力是产生误差的主要原因。在实验数据中考虑空气粘滞阻尼力的影响,可使实验误差从4.3%降低到0.3%。     

The temperature window of minimum flow resistance in melt flow of polyethylene. Further studies on the effect of strain rate and branching

The existence of a narrow temperature window (150–153°C) of smooth extrudability coupled with a minimum in flow resistance (extrusion pressure) in high-molecular weight polyethylene (>4 × 10⁵ g mol^?1) was the subject of a previous article where it was associated with strain-induced formation of the mobile hexagonal mesophase. The new findings of this note show that this minimum in flow resistance only sets in above a critical strain rate; this is interpreted in terms of the requirement of a critical strain rate in order to stretch molecules to their fully extended configuration. Furthermore, this critical strain rate is shown to be higher for lower molecular weight materials, in agreement with a priori considerations. Additionally, the temperature at which the pressure minimum occurs in a polyethylene containing methyl branches shifts to a significantly lower value than that for the linear material. This is interpreted in terms of the ? CH₃ groups raising the crystal free energy, thereby lowering the temperature at which the transition to the hexagonal phase occurs.