稀土元素在LD30铝合金真空钎焊中的作用

研究了添加La和Ce的Al-Si基钎料真空钎焊LD30铝合金接头的力学性能，微观组织形貌和EDS，并与未添加稀土元素的Al-Si基钎料真空钎焊接头进行对比。结果表明，添加稀土元素的LD30铝合金真空钎焊接头抗拉强度为288MPa，达母材抗拉强度的97．6％，明显高于未添加稀土的LD30合金真空钎焊接头。其机制在于La,Ce能够明显提高Al-Si基钎料与LD30铝合金的润湿性能，改善LD30铝合金真空钎焊接头焊缝及其基体中杂质元素的分布，促进钎料和母材中各元素的均匀扩散，从而提高真空钎焊接头的力学性能。     

The structure factor for liquid lead

Abstract

The structure factor for liquid lead at the temperatures 613 K, 643 K, 863 K and 1163 K are measured by neutron diffraction. Extensive comparisons to earlier measurements are made as well as comparisons to different hard-core models.     

Cellulase retention and sugar removal by membrane ultrafiltration during lignocellulosic biomass hydrolysis

Technologies suitable for the separation and reuse of cellulase enzymes during the enzymatic saccharification of pretreated corn stover are investigated to examine the economic and technical viability of processes that promote cellulase reuse while removing inhibitory reaction products such as glucose and cellobiose. The simplest and most suitable separation is a filter with relatively large pores on the order of 20–25 mm that retains residual corn stover solids while passing reaction products such as glucose and cellobiose to form a sugar stream for a variety of end uses. Such a simple separation is effective because cellulase remains bound to the residual solids. Ultrafiltration using 50-kDa polyethersulfone membranes to recover cellulase enzymes in solution was shown not to enhance further the saccharification rate or overall conversion. Instead, it appears that the necessary cellulase enzymes, including β-glucosidase, are tightly bound to the substrate; when fresh corn stover is contacted with highly washed residual solids, without the addition of fresh enzymes, glucose is generated at a high rate. When filtration was applied multiple times, the concentration of inhibitory reaction products such as glucose and cellobiose was reduced from 70 to 10 g/L. However, an enhanced saccharification performance was not observed, most likely because the concentration of the inhibitory products remained too high. Further reduction in the product concentration was not investigated, because it would make the reaction unnecessarily complex and result in a product stream that is much too dilute to be useful. Finally, an economic analysis shows that reuse of cellulase can reduce glucose production costs, especially when the enzyme price is high. The most economic performance is shown to occur when the cellulase enzyme is reused and a small amount of fresh enzyme is added after each separation step to replace lost or deactivated enzyme.     

Mechanical properties of single motor molecules studied by three-dimensional thermal force probing in optical tweezers.

A new method combining three-dimensional (3D) force measurements in an optical trap with the analysis of thermally induced (Brownian) position fluctuations of a trapped probe was used to investigate the mechanical properties of a single molecule, the molecular motor kinesin. One kinesin molecule attached to the probe was bound in a rigorlike state to one microtubule. The optical trap was kept weak to measure the thermal forces acting on the probe, which were mainly counterbalanced by the kinesin tether. The stiffness of kinesin during stretching and compression with respect to its backbone axis were measured. Our results indicate that a section of kinesin close to the motor domain is the dominating element in the flexibility of the motor structure. The experiments demonstrate the power of 3D thermal fluctuation analysis to characterize mechanical properties of individual motor proteins and indicate its usefulness to study single molecule in general     

Preparation of Copper Chromite by Vaccum Freezing Drying Method and Its Catalytic Activity for Sulfuric Acid Decomposition

Iodine sulfur (IS) process is one of the most promising routes for massive and CO₂‐free hydrogen production. Among the three reactions IS process composed, decomposition of sulfuric acid is the most energy intensive step and has to be conducted in the presence of catalyst. In this work, copper chromite (CuCr₂O₄) was prepared, characterized, and used as the catalyst for sulfuric acid decomposition reaction. The co‐precipitation preparation method of CuCr₂O₄ which featured in vacuum freezing drying (VFD), was applied, and the main factors which influence the structure of CuCr₂O₄ such as pH values of the co‐precipitation solution and calcination temperature were investigated. Results showed that pH value affected the size of copper chromite granule, when pH was between 7 and 8, the size of prepared CuCr₂O₄ was in nanometer scale. Calcination temperature influenced the purity of the crystal. The samples were characterized by XRD, TEM and BET. The catalytic activity of CuCr₂O₄ prepared by VFD was evaluated and compared with CuCr₂O₄ prepared by usual co‐precipitation method and Pt/Al₂O₃. Results showed that the activity of CuCr₂O₄ was close to that of Pt catalyst, but apparently higher than that of CuCr₂O₄ prepared by usual method. In addition, it presents good stability in the 70 h test. Therefore, it was promising to be used in the sulfuric acid decomposition step of IS process.     

The preparation of 7-substituted norbornadiene-2,3-dicarboxylic anhydrides and an experimental and theoretical study of their reactivity

Four new substituted methano-bridged or heteroatom-bridged norbornadienomaleic anhydrides have been prepared and converted to sesquinorbornadiene anhydrides by reaction with cyclic 1,3-dienes. The versatility of parity reversal, in conjunction with N-substituent steric effects, has been used to produce all three possible stereoisomers of the N,O-sesquinorbornadiene anhydrides in separate, stereoselective cycloadditions. The anhydrides have been synthesized by cyclization of their diacids (in situ production) or by flash vacuum pyrolysis of their furan adducts (yielding crystalline products); further fragmentation occurs at these or higher temperatures to produce five-membered carbocyclic or heterocyclic anhydrides. Activation energies have been evaluated for the fragmentation and cycloaddition processes using DFT calculations (B3LYP/6-31G∗) and these calculations correctly predict, which reaction can be intercepted at the norbornadienomaleic anhydride stage and preferred stereochemistry of cycloadducts.     

The sound velocity in ideal liquid mixtures from thermal volume fluctuations.

The selection of the correct mixing rule for sound velocity in ideal liquid mixtures determines the interpretation of the sound velocity in real mixtures. This is especially important for the determination of apparent properties of solutes, such as their apparent compressibility. There are different approaches reported in the literature, and this article presents a new derivation of the mixing rule based on statistical mechanics. It is shown that the correlation of volume fluctuations between adjacent components has a crucial influence on the ideal mixing rule.     

Unexpected valence bond isomerization of [1,2,4]triazolo[3,4-c][1,2,4]benzotriazines under flash vacuum pyrolytic (fvp) conditions

Flash vacuum pyrolysis (fvp) of some substituted [1,2,4]triazolo[3,4-c][1,2,4]benzotriazine derivatives (1a-d) has been studied between 450 and 600 °C. The only transformation observed up to 525 °C was the unexpected valence bond isomerization of the angularly fused starting compounds to the isomeric linearly fused [1,2,4]triazolo[4,3-b][1,2,4]benzotriazine derivatives (9a-d), whereas at higher temperatures fragmentation products such as aromatic nitriles were also formed. Kinetic measurements revealed negative entropies of activation in the isomerization process, which suggest a concerted ring closure reaction to an intermediate antiaromatic diazirine. Reversibiblity of the title isomerization reaction was also proved by FVP experiments.     

Small angle X-ray scattering investigations of thermodynamic properties of fluid mixtures

Absolute small angle X-ray studies of concentration fluctuations were performed in order to determine thermodynamic properties of a model blend, consisting ofn-hexane and perfluoro-n-hexane. The quantities which we determined were the second derivate of the Gibbs free energy of mixing with respect to the concentration of the components, the location of the spinodal, interaction and solubility parameters, the energy gradient density coefficient as well as the correlation length of the fluctuations at various compositions and temperatures, particularly in the neighbourhood of the spinodal and the critical point. The data obtained were compared with those obtainable from the well known location of the binodal, to test the reliability of the scattering method.     

High performance carbon–carbon composites obtained by a two-step process from phthalonitrile matrix composites

Carbon–carbon composites (C/C) were produced from carbon fiber reinforced phthalonitrile (CFRP) matrix composites in a two-step impregnation–carbonization procedure. After graphitization at 1800 °C, the obtained C/C composites demonstrated highly crystalline structure and properties characteristic of composites derived from phenolic matrix CFRP by the industrial procedure: d = 1.73 g cm^?3, interlaminar shear strength was 14.1 MPa, compression strength was 139.8 MPa, and coefficient of friction was in the range 0.32–0.34.