尾水管水力振动的监测与故障判断

从模型及真机试验结果出发，叙述混流式水轮机一般的水力故障形式，研究了尾水管的水力振动特点及振动随运行工况而变化的情况，介绍了以压力脉动频率及幅值作为特征参量对尾水管进行振动监测及故障判断的方法。     

幅相一致行波管高频电路CAD研究

 在行波管的设计和装配过程中，各部件的尺寸必须严格控制，高频电路参数的离散对行波管色散特性有极大的影响。使用螺旋导电面模型，模拟计算了高频结构各主要参数离散对色散特性和轴向互作用耦合阻抗的影响。分析计算了夹持杆宽度、翼片高度、螺旋线平均半径、螺距、夹持杆介电常数等离散时对色散特性和轴向互作用耦合阻抗的影响，为新型幅相一致行波管的设计和生产提供了很有价值的参考建议。     

水轮机水力稳定性的分析

根据收集国内外水轮机水力稳定性资料 ,分析了引起水轮机水力不稳定性的因素 ,并结合实例分析可能引起的危害 ,最后提出了解决问题的方法和建议     

The push-out region of an immersed manifold

We consider immersions: and construct a subspace of which corresponds to a set of embedded manifolds which are either parallel to f, tubes around f or, in general, partial tubes around f. This space is invariant under the action of the normal holonomy group, We investigate the case where is non-trivial and obtain some results on the number of connected components of . Received 24 March 2000.     

Polytetrafluoroethylene and metal structure convective-flow CO laser

A convective flow CO laser composed of polytetrafluoroethylene discharge tubes, nickel–chromium steel components, a cupric heat exchanger and other components is described. Operating in liquid nitrogen condition, output power of 60 W has been obtained from a non-selective cavity.     

双面加热环形通道内干涸点的确定

根据环形管通道内流体流动和换热的特点,以Kirillov和Smogalev提出的干涸点理论模型假设为基础,从最基本的质量守恒方程出发,并引入临界液膜厚度等相应的辅助模型,得到了双面加热环形通道内流动沸腾干涸点的理论模型。同时针对间隙为1.0mm和1.5mm的环形窄缝进行了低压低质量流速工况下干涸点的实验研究。比较发现理论模型预测值与实验结果基本相符。说明本文提出的理论模型适用于低压低流量条件下的窄环形通道。实验同时发现:环状流临界热流密度在系统压力为2.2MPa达到最大值,临界含汽量随质量流速的增大呈缓慢下降趋势。     

Fully developed mixed convection in horizontal and inclined tubes with uniform heat flux using nanofluid

Fully developed laminar mixed convection of a nanofluid consists of water and Al₂O₃ in horizontal and inclined tubes has been studied numerically. Three-dimensional elliptic governing equations have been solved to investigate the flow behaviors over a wide range of the Grashof and Reynolds numbers. Comparisons with previously published experimental and numerical works on mixed convection in a horizontal and inclined tube are performed and good agreements between the results are observed. Effects of nanoparticles concentration and tube inclinations on the hydrodynamics and thermal parameters are presented and discussed. It is shown that the nanoparticles concentration does not have significant effects on the hydrodynamics parameters. Heat transfer coefficient increases by 15% at 4 Vol.% Al₂O₃. Skin friction coefficient continually increases with the tube inclination, but the heat transfer coefficient reaches a maximum at the inclination angle of 45°.     

用毛细管测量纯水表面张力系数的误差讨论

通过用毛细管测量纯水表面张力系数实验，得到管内径d与接触角θ的相对误差之间的关系曲线，由此说明实验测得的表面张力系数α和理论公式相比呈现一定的偏差，并简单地讨论了实验的理想状态与实际情况的差别．     

螺旋线径向挤压变形对其慢波结构冷测特性的影响

 介绍了用MAFIA软件的准周期边界条件计算螺旋线行波管慢波结构的色散和耦合阻抗，以及用ANSYS软件对螺旋线径向挤压变形建模的方法，并对螺旋线受挤压径向变形对其冷测特性的影响进行了详细的分析。结果表明:螺旋线径向挤压变形会导致相速增大，而在通常的变形范围内耦合阻抗也会增加；当变形继续增大时耦合阻抗上升到最大值后开始下降。     

Dielectric effect on the rf characteristics of a helical groove travelling wave tube

A new type of partial-dielectric-loaded helical groove slow-wave structure (SWS) for millimetre wave travelling wave tube (TWT） is presented in this paper.The radio-frequency characteristics including the dispersion properties,the longitudinal electric field distribution and the beam-wave coupling impedance of this structure are analysed.The results show that the dispersion of the helical groove circuit is weakened,the phase velocity is reduced and the position of the maximum Ez is moved from the mouth to the inside of the groove after partially filling the dielectric materials in the helical groove SWS.Therefore,the dielectric-loaded helical groove SWS is suitable for a multi-beam TWT with broad band and high gain.