Toward Fuzzy Optimization without Mathematical Ambiguity

Fuzzy programming has been discussed widely in literature and applied in such various disciplines as operations research, economic management, business administration, and engineering. The main purpose of this paper is to present a brief review on fuzzy programming models, and classify them into three broad classes: expected value model, chance-constrained programming and dependent-chance programming. In order to solve general fuzzy programming models, a hybrid intelligent algorithm is also documented. Finally, some related topics are discussed.     

场协同理论在椭圆型流动中的数值验证

本文用数值模拟的方法，通过四个椭圆型流动传热的例子验证了场协同理论的正确性．结果表明，场协同理论不仅适合于抛物型流动，亦适合于复杂的有回流的椭圆型流动．     

机翼大攻角下失速颤振的气动弹性研究

本文采用流固耦合的数值方法研究了机翼在0°～50°攻角下的颤振。计算结果表明,随着来流攻角α0的增大,机翼的固有频率对颤振的影响越来越大,颤振由线性的强迫振动逐渐发展成为非线性的自激振动,而当α0增加到一定程度以后,大尺度分离流交替地从机翼头部和尾部产生,机翼和流场会发生共振,引起机翼的失速颤振。     

1+1/2对转涡轮叶排轴向间距对性能影响的研究

木文对1+1/2对转涡轮中轴向间距影响进行了初步研究。对不同轴向间距叶栅流场进行了大量时间精确模拟。研究表明,1+1/2对转涡轮高低压转叶间轴向间距成为追求高效率的制约因素,轴向间距为高压转叶喉部宽度是关键点。因此有关小轴向间距下强激波/叶排干扰的研究应该加强。     

轴流风扇叶片端导叶作用的研究

本文采用数值方法研究了叶片端导叶对轴流风扇性能的影响。通过与普通开式轴流风扇比较,分析了叶片端导叶对内部流动作用的机理.数值计算结果表明:叶片端导叶的安装位置将影响轴流风扇气动效率,安装叶片端导叶不能提高风扇静压升,但是在压力面安装时能有效地减小风扇叶顶泄漏流与主流的掺混损失;在设计流量下,压力面安装叶片端导叶使泄漏涡的作用范围较小,涡核更靠近吸力面;吸力面安装叶片端导叶弱化了泄漏涡的强度但没有减小泄漏涡的作用范围。     

液压支架压力变送器的电路设计

分析了液压支架的压力特性并提出对压力变送器的技术要求，阐述了压力传感器的选择和外围电路的设计，对压力变送器的信号调理电路进行了仿真分析。     

Tensile behaviour of corroded and hydrogen embrittled 2024 T351 aluminum alloy specimen

The synergetic effect of corrosion and corrosion induced hydrogen embrittlement damage processes which occur at local scale has been found to result in a dramatic macroscopic tensile ductility loss of the 2024 aluminum alloy. In the present work, the tensile behaviour of corroded 2024 T351 specimens has been estimated on the basis of FE analysis by taking into account the local material properties in the damaged areas. A parametric study is involved to account for the effect of thickness in the results. Calculated tensile properties obtained with the analysis agree well with experimental data.     

基于MATLAB的控制系统CAI设计

基于MATLAB开发平台，利用其可视化编程能力的GUI，对控制系统进行分析、设计与仿真，开发了控制系统CAI应用软件，它具有较强的教学、实验、工程应用价值。     

MATLAB/SIMULINK在电力系统仿真中的应用

介绍了Matlab／Simulink仿真工具在电力系统仿真中的应用方法．     

Atomic-scale simulation of nano-grains:structure and diffusion properties

Nanograins are characterized by a typical grain size from lto 100 nm.Mclecular dynamics aimubations have been carried out for the nanograin sphere with the diameters from 1.45 to 10.12 nm.We study the influence of grain size on structure and diffusion properties of the nanograins.The results reveal that as the grain size is reduced,the fraction of grain surface increases significantly,and the surface width is approximately constant；the diffusicn coefficlent is increased sharply,and the relation of the diffusion coefficient and the grain size is close to exponential relation below 10nm.