炼镁还原罐材质的成份设计

本文针对炼镁还原罐在使用条件下的破坏形式及对该材质的成份设计进行了分析 ,还原罐材质在具有单一奥氏体的基础上 ,进行良好的合金化处理是提高其抗蠕变性和热强性的有效方法 ,对提高材质的使用寿命起到良好的作用。     

Lanthanum nitrate decomposition by both temperature programmed heating and citrate gel combustion

Thermal decomposition of lanthanum nitrate to lanthanum oxide was carried out by both temperature programmed heating (TPH) and citrate-gel combustion. The temperature programmed heating was carried out under flow of oxidizing (air), neutral (nitrogen) and reducing (25 vol.% hydrogen+argone mixture) gases, and the processes were controlled by simultaneous thermogravimetry and differential thermal analysis. It was shown that hydrogen atmosphere helps to reduce temperatures of all decomposition steps. The results of TPH were utilized to check the nature of residues in the products of lanthanum nitrate-to-oxide conversion performed via citrate-gel combustion technique.     

非设计工况下叶轮进口附近的流动及其控制

对叶轮进口附近流动在偏离设计工况下的回流和汽蚀(空化)两大特性进行了系统的描述,阐述了它们的诱发机理及其对泵性能的影响.根据回流的诱发机理对诱导轮的作用进行了全面的分析,提出了控制回流发生的有效方法,从叶片进口流动这一角度完善了离心泵叶片设计理论.     

Intrinsic thermal stability and quenching recovery of thin-film superconductors with thermal boundary resistance

The stability behaviour of a thin-film superconductor under a localized release of thermal disturbance is investigated. Two-dimensional conjugate film/substrate conduction equation with anisotropic thermal conductivity of the film, and Joule heat are employed to investigate effects of substrate and thermal properties on the intrinsic stability and quenching recovery. To consider the thermal boundary resistance between film and substrate, an interfacial-layer model (ILM) with very low diffusivity and an acoustic mismatch model (AMM) are employed. Results show that the thermal boundary resistance influences strongly the intrinsic stability. Thermal boundary resistance increases intrinsic stability if the thermal conductivity of the substrate or the disturbance energy is large. Higher Biot numbers and thermal conductivity ratios of film to substrate in longitudinal direction influence stability favorably. We demonstrate also that operation of a film/substrate system, such as YBCO/MgO, is either intrinsically stable or irrecoverably unstable.The authors wish to express their sincere appreciation to Dr. R. C. Chen for his invaluable advice and suggestions during the course of this paper. This research was supported by the National Science Council of the R. O. C. through grant NSC 83-0401-E-009-006. The computations were performed on the IBM ES/9000 at the National Center For High-Performance Computing.     

人体形态学参数的回归方程

在汉纳范模型的基础上，增加了３个有关躯干的围度指标。通过代表人体主要特征的形态学参数，利用逐步回归分析法，建立回归方程。用以预测那些不易测准或需专门测量仪器检测的参数，简化了模型的个体化过程。     

Relations among eigenvalues of Sturm-Liouville problems with different types of leading coefficient functions

For any Sturm-Liouville problem with a separable boundary condition and whose leading coefficient function changes sign (exactly once), we first give a geometric characterization of its eigenvalues λn using the eigenvalues of some corresponding problems with a definite leading coefficient function. Consequences of this characterization include simple proofs of the existence of the λn's, their Prüfer angle characterization, and a way for determining their indices from the zeros of their eigenfunctions. Then, interlacing relations among the λn's and the eigenvalues of the corresponding problems are obtained. Using these relations, a simple proof of asymptotic formulas for the λn's is given.     

Ageing of wet-synthesized oxide powders

Wet chemical synthesis of precursor oxide ceramics is a method to obtain small particulate powders. Such powders are far more prone to ageing in air than more traditional precursors. Thermogravimetric analysis is used to highlight the species responsible for the ageing of ceramic precursors. Indeed water and carbon dioxide are observed to evolve from aged powders. Ceramics obtained from aged precursors can reach a very low final density with respect to the theoretical value. A large degree of the original sintering properties can be recovered after washing the aged powders with ethanol in a basic medium.     

On the Use of the Restitution Condition in Flexible Body Dynamics

The difference between the classical treatment offlexible body impact and the treatment of impact in flexiblemultibody dynamics is due to several fundamental reasons. Inthe classical impact theory, simple structures such as beamsand plates are used. Infinite dimensional models can bedeveloped for these simple structural elements to study theimpact dynamics and the wave propagation problem. Flexiblemultibody impact problems, on the other hand, involve bodieswith complex geometry that cannot be modeled using infinitenumber of degrees of freedom. Furthermore, the classicalimpact theory has been mainly concerned with the impactbetween a rigid mass that moves without constraints beforeit impacts a simple flexible structure. This is not amultibody simulation scenario in which the impact occursbetween kinematically constrained bodies that are subjectedto impulsive constraint forces in addition to the impactforces. These constraint forces can influence the motion ofthe two bodies immediately after impact, and as aconsequence, the simple classical theory scenario of impactdoes not apply. It is the objective of this paper to discussthe use of the restitution condition in flexible multibodyimpact problems and demonstrate that the use of thisapproach does not exclude the classical formulation.Nonetheless, the impulse momentum balance approach can serveas an effective and efficient procedure for solving theimpact problem in finite dimensional models that do not obeythe classical wave theory. Energy results of simplestructural elements are presented in order to demonstratethe consistency of using the impulse momentum balanceapproach in solving impact problems in finite dimensionalflexible body applications.     

Graphitic nanofillers in PMMA nanocomposites—An investigation of particle size and dispersion and their influence on nanocomposite properties

Mechanical, thermal, and electrical properties of graphite/PMMA composites have been evaluated as functions of particle size and dispersion of the graphitic nanofiller components via the use of three different graphitic nanofillers: “as received graphite” (ARG), “expanded graphite,” (EG) and “graphite nanoplatelets” (GNPs) EG, a graphitic materials with much lower density than ARG, was prepared from ARG flakes via an acid intercalation and thermal expansion. Subsequent sonication of EG in a liquid yielded GNPs as thin stacks of graphitic platelets with thicknesses of ～10 nm. Solution‐based processing was used to prepare PMMA composites with these three fillers. Dynamic mechanical analysis, thermal analysis, and electrical impedance measurements were carried out on the resulting composites, demonstrating that reduced particle size, high surface area, and increased surface roughness can significantly alter the graphite/polymer interface and enhance the mechanical, thermal, and electrical properties of the polymer matrix. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2097–2112, 2007