埋藏式钢管的抗外压稳定研究

应用壳体稳定理论结合某一工程实例研究了圆形加劲环式钢管和锚筋式钢管的抗外压稳定问题。首先分析了非对称外压对失稳荷载的影响;其次根据壳体稳定分析结果对锚筋式和加劲环式钢管的失稳形态和影响因素进行了分析,并对现有计算公式进行了评述。结果表明,对锚筋式和加筋环式钢管采用本文提出的按壳体稳定理论建立的有限元计算公式是可靠合理的。     

同时快速更换轧辊和导卫的高刚度机座

提出了一种可同时快速更换轧辊和导卫装置的高刚度轧机机座,适用于棒材、线材和型材轧制．该机座在机架上安装一个称为卡式箱的装置,卡式箱内可以预装轧辊和导卫,并在轧制线外调整好,可以实现轧辊和导卫一次吊装,快速更换．     

原子吸收光谱法测定拉伸断口铬镍钼钛钢样品中主成分

研究了毫克级铬镍钼风样品中主成分镍的火焰原子吸收光谱法（FAAS法）和铬、钼、钒、钛、铝的塞曼恒温平台石墨炉原子吸收光谱法（ZSTPF－AAS法）。采用了微波溶样技术作为防污染样品预处理技术，采用石墨管硅涂层改进技术提高了仪器的测试精度。其中铬、镍、钼、钒、钛、铝的相对标准偏差分别为2.7%,0.97%,8.6%,7.3%,1.7%,7.3%。其加标回收率分别为96.5%,97%,96.7%,93%,98%,91%。通过分析，发现在较低温度下铬镍钼钛钢断面上有轻微的钼偏析现象，可能是拉伸断裂的主要化学影响因素。     

Thermal analysis of low alloy Cr-Mo steel

The paper deals with results of thermal analysis of low-alloyed chromium-molybdenum steel. The methods of analysis were dilatometry, differential thermal analysis (DTA) and differential scanning calorimetry (DSC). The Ac₁ and Ac₃ temperatures of the steel samples measured by dilatometry and DTA during the heating period were in good agreement. Generated by cooling a martensitic structure first became apparent at 503 K. Tempering of the as-quenched samples showed the presence of the second tempering stage in the region between 473 and 573 K. At that stage heat capacity decreased from 0.48 to 0.32 J g^-1 K^-1, as a result of conversion of transition carbide due to heat consumption. After normalization of the as-quenched samples the heat capacity values were restored to between 0.42 and 0.47 J g^-1 K^-1 in the temperature range from 373 to 673 K. This revised version was published online in August 2006 with corrections to the Cover Date.     

Molecularly-imprinted polypyrrole-modified stainless steel frits for selective solid phase preconcentration of ochratoxin A

A molecularly-imprinted polymer (MIP) was prepared by electropolymerization of pyrrole (Py) onto a stainless steel frit, using ochratoxin A (OTA) as the template, in order to make a micro solid phase preconcentration (SPP) device. The OTA template was removed with 1% triethylamine (TEA) in methanol. Compared to non-imprinted polypyrrole (PPy), the molecularly-imprinted polypyrrole (MIPPy) enhanced the selective binding of OTA. The percentage recovery improved from 0 to 40% when the OTA sample solution was acidified with 1 M HCl (1% by volume). At a flow rate of 0.2 mL/min, maximum OTA binding was reached in 6 min after a total loading of 3.2 ng OTA. Final elution of the OTA was analyzed by high performance liquid chromatography (HPLC) with fluorescence detection, using 20:80 v/v acetonitrile–ammonia buffer (NH₄Cl/NH₃, 20 mM, pH 9.2) as the mobile phase. The MIPPy-SPP-HPLC results clearly demonstrated that the MIPPy-SPP device afforded selective preconcentration of OTA from red wine samples, at OTA concentration levels as low as 0.05 ppb, prior to HPLC analysis.     

Sol-gel ZrO2 coatings for chemical protection of stainless steel

ZrO₂ coatings deposited on 316 L stainless steel sheets were synthesized by sol-gel method using Zr(OC₃H₇)₄ as precursor and isopropanol, glacial acetic acid, and water as solvents for application with ultrasounds. Different solutions for dip-coating were prepared with compositions varying between 0.025 and 0.9 mol/dm³ of ZrO₂. X-ray diffraction shows that the films densified at 800°C are crystalline with a tetragonal structure. The thickness of the coatings varied from 0.35–0.75 m. The influence of the ZrO₂ coatings on the corrosion behavior of stainless steel substrates in aqueous NaCl was studied through potentiodynamic polarization curves at 1 mV/s. The values of the electrochemical parameters allow for an explanation of the role of the films in the increased resistance of steel against corrosion in moderately aggressive environments.     

Sample evaporation in conventional GC split/splitless injectors. Part 1: Some quantitative estimates concerning heat consumption during evaporation

During sample evaporation in conventional vaporizing injection, the supply of heat to the evaporating liquid is a problem, first because the amounts of heat consumed are relatively large and, secondly, because the heat must be transferred to the sample within a very short time. Times available for evaporation, required amounts of heat, possible sources of heat, and the time required to transfer the heat to the sample liquid are discussed. It is shown that mixing with carrier gas contributes little heat to the evaporation process, but also that packings with glass wool have too low a heat capacity to deliver the required amount of heat to the evaporating sample. Transfer of heat from the insert wall to the sample easily requires several seconds, even if cooling of the vaporizing zone by 20° is accepted. Thus “flash evaporation” is usually impossible and most liquids must be held in the vaporizing chamber to allow full evaporation.     

Assessment of corrosion resistance of surface-coated galvanized steel by analysis of the AC impedance spectra measured on the salt-spray-tested specimen

In the present work, corrosion resistance of surface-coated galvanized steel was quantitatively determined by an analysis of the alternating current (AC) impedance spectra measured on the salt-spray-tested specimen. To evaluate the corrosion resistance of the surface-coated galvanized steel, AC impedance spectroscopy was performed on the salt-spray-tested specimen previously exposed to salt-sprayed corrosive environment. From the analysis of the impedance spectra, the area fraction transient of white rust θ ₂(t) was theoretically derived from the equivalent circuit equation by using two fitting parameters. The values of the two fitting parameters were determined by fitting the empirical transient equations to the area fraction of the resin coating layer and to the total resistance obtained from the impedance spectra measured, respectively. From the analyses of θ ₂(t) for four kinds of surface-coated galvanized steels with various resin coating layers, it is indicated that as the values of the two fitting parameters decrease in the order of CP, GI, OD and OM (commercial trade names) specimens, the corrosion resistance increases in that order as well. Furthermore, from the quantitative comparison of the two fitting parameters with the polarization resistance of the upper resin coating layer R _p determined from the potentiodynamic polarization curve, it is suggested that the two fitting parameters decrease in value as well with increasing R _p.     

Protective properties of redox polymer film deposited on stainless steel

We propose a novel composite organic-inorganic coating in the form of a redox polymer film for protection of stainless steel against general corrosion in strong acid medium (2 M H₂SO₄). We utilize an anion exchange polymer, protonated poly(4-vinylpyridine), into which hexacyanoferrate anions have been introduced. Owing to the presence of Fe(CN)₆^3–/4– at the interface formed by the film and the steel, a sparingly soluble metal hexacyanoferrate (mostly Prussian blue, PB) is formed as an overcoating on the steels surface, presumably on the passive (metal oxide) layer. The redox polymer film on the steel seems to act as a composite three-dimensional bilayer-type coating in which hexacyanoferrate(III,II) anions (that are capable of effective charge storage) exist in the outer portions of the film, whereas the inner PB layer improves the systems overall adherence and stability. By analogy to a conducting polymer (e.g. polyaniline, polypyrrole), introduction of the redox polymer composite film leads to stabilization of the steel substrates potential within the passive range.Contribution to the 3rd Baltic Conference on Electrochemistry, Gdansk-Sobieszewo, Poland, 23–26 April 2003Dedicated to the memory of Harry B. Mark, Jr. (28 February 1934–3 March 2003)     

Evaluation of epifluorescence image analysis of biofilm growth on stainless steel surfaces

Biofilm growth of Bacillus subtilis, Pseudomonas fragi, Pediococcus inopinatus and Listeria monocytogenes was studied on stainless steel surfaces at room and low temperatures to evaluate the results of traditional hygiene measures. The results were compared with those of image analysis of stainless steel surfaces in an epifluorescence microscope. Statistical analyses were carried out to determine the variations between the conventional cultivation swab method, the glycocalyx amount obtained using swabbing, and the values of the areas of the biofilm, slime and cells. As a general rule, old biofilms showed total counts at approximately the same levels as the young biofilm. The results showed that temperature affected the results for all strains except B. subtilis. The strains of Pe. inopinatus and Ps. fragi showed increased attachment at 6°C and L. monocytogenes at 25°C. The biofilm slime was more easily detached than the cells. The results indicated that the traditional swab method is not reliable for the measurement of biofilm formation on surfaces.