火花激发原子发射光谱分析不锈钢线材

火花激发原子发射光谱法应用于直径小于8mm的不锈钢线材的分析，对此类试样应用了一种特制的夹具，用块状标准样品制作工作曲线。由于线状试样和块状标准样品之间的形状差异所产生的系统不确定度借采用同类型标样作校正，对共存元素的相互干扰也采用了相应的校正方法。其它分析条件，包括严格的制样工序，氩气的纯度要求及其流量控制，以及光源的最佳条件等，作了深入的试验。按所提出的方法测定了不锈钢线材试样中碳、硅、锰、磷、硫、铬、镍及钛等8个元素。经校正后的结果与化学法测得结果相符。     

32Cr2MoVA合金结构钢标准物质的研制

本标准物质系合金钢。主要成份有碳、硅、锰、磷、硫、铬、镍、钼、钒,同时还含有锡、铅、砷、锑、铋等微量元素,每种元素成份都具有良好的线性关系。它可作为量值传递和仲裁分析的依据,同时也可用于校验分析仪器与分析方法的正确性和可靠性。     

原子吸收分光光度法测定钢铁中的铬

在稀硝酸介质中,不需分离其它干扰杂质,用原子吸收分光光度法直接测定中、低合金钢中的铬。该法测定铬的特征浓度(灵敏度)为0.08μg/mL,铬含量在0~6μg/mL内与吸光度线性相关,检出限为0.003μg/mL。该法测定速度快,与标准法测定结果的相对误差在±4.6%以内,回收率为97%~115%。     

应变速率和电位对应力腐蚀裂纹扩展的影响

以滑移-溶解-再钝化模型为基础,推导出应力腐蚀裂纹扩展速率与裂尖应变速率和电位之间的理论公式.计算表明,在裂纹扩展速率与裂尖应变速率的关系曲线中有两个特征区域.裂纹扩展速率在区域I随裂尖应变速率增加而增大,而在区域II不随裂尖应变速率的改变而变化.用慢应变速率拉伸技术（SSRT）测量了304L不锈钢的裂纹增长速率.当电位控制在区域II的阳极区时,理论计算的裂纹扩展速率与实验得到的结果比较吻合.     

Metal Nanoparticles on Stainless Steel Surfaces as Novel Heterogeneous Catalysts

The goal of this work was the development of a novel type of heterogeneous catalyst, consisting of bare metal nanoparticles on stainless steel foils, which can be shaped to any kind of architecture and, if necessary, heated electrically. Solutions of pre-prepared, ligand protected and monodispersed gold, palladium, platinum and rhodium nanoparticles were sprayed onto stainless steel foils, followed by the careful removal of the ligand molecules by an oxygen plasma treatment. Due to this, bare particles become irreversibly fixed on the steel support. It could be shown that the original particle sizes do not change during the plasma treatment. Foils, densely coated with the nanoparticles, were used for gas phase catalyses in a self-made reactor at room temperature or at 60 °C. Hydrogenation of 1,3-butadiene at 15 nm Pd and 2 nm Pt, CO oxidation at 16 nm, 8 nm and 1.4 nm gold and NO reduction with NH₃ at 2 nm Rh particles were performed, indicating that the novel catalysts might in principle be applicable in technical processes if the experimental conditions like form and temperature would be optimized. Dedicated to Professor Dieter Fenske on the occassion of his 65th birthday.     

稀土在低硫铌钛钢中的作用

在实验条件下采用50kg真空感应炉炼和两段控制轧制工艺，并采用WE－60型万能拉伸试验机，JB－30B型冲击试验机，MM6型及OLYMPUS－PME3型光学金相显微镜，IBAS－2000图相分析等手段研究了稀土对低硫铌钛钢性能，组织及夹杂物的影响。在低硫铌钛钢中的试验结果表明，稀土元素的加入使力学性能变化各异，它使钢的横向屈服点和抗拉强度先下降而后上升；延伸率则无下降而后上升；稀土对钢的横向冲击功则表现为先上升而后下降，并且在－20℃以上，适量的稀土加入可以明显改善其冲击功的各向异性；稀土的加入并不能改变钢的显微组织类型，钢的组织为铁素体＋珠光体，但稀土会使钢中珠光体数量增加，铁素体数量减少，在钢中夹杂物方面，稀土加入则表现为它一方面 化钢液，使钢中夹杂物数量减少，另一方面是使钢中夹杂物的颗粒球化，细化和弥散化，从而改善夹杂物的分布。     

高镍钢中镍的测定

以王水溶解试样，用氨水作沉淀剂，并加入适量三乙醇胺及柠檬酸进行掩蔽，以消除铁及铬等元素的干扰，在pH=3-6的酸性介质中，加入过量的EDTA标准溶液，使镍与EDA形成稳定的络合物，以PAN为指示剂，用硫酸铜标准溶液滴定过量的EDTA标准溶液，从而求得镍的含量。     

Determination of boron in boron-alloyed steels by inductively coupled plasma atomic emission spectrometry

An inductively coupled plasma atomic emission spectrometry (ICP-AES) procedure has been developed and examined for the determination of boron content (0.01 up to about 2% B) in boron-alloyed steels such as POLDI ATA BOR (65% Fe, 19%Cr, 12% Ni, 1.5% Mn, 1% B), POLDI ATA BOR EXTRA (62% Fe, 18% Cr, 13% Ni, 2.5% Mo, 1.5% Mn, 1% B) and POLDI ATA BOR-R (75% Fe, 18% Cr, 3.5% Ti, 1.8% B). The steel sample is dissolved with a mixture of hydrochloric, nitric, sulfuric and phosphoric acids in a quartz vessel. Borides of alloyed metals, especially of iron and chromium, are quantitatively decomposed. The presence of phosphoric acid in a sample solution reduces the volatility of boric acid with water vapour.Presented in part at the 1989 European Winter Conference on Plasma Spectrochemistry, Reutte, Austria     

稀土变质热锻模具铸钢高温磨损性能的研究

研究了稀土（RE）变质热锻模具铸钢的高温磨损性能，并与热锻模具钢H13钢和3Cr2W8V钢进行对比，探讨了稀土元素的作用和热锻模具铸钢的高温磨损机理。结果表明：随着RE加入量的增加，热锻模具铸钢的磨损率先减后增，RE加入量在质量分数为0．05％时热锻模具铸钢具有最佳的高温磨损性能。RE变质热锻模其铸钢的高温耐磨性明最高于H13钢和3Cr2W8V钢。高温磨损机理为氧化磨损和氧化物的疲劳剥落，磨屑为块状的Fe2O3和Fe3O4。     

Extraction-spectrophotometric study on the vanadium(V)-2,3-dihydroxynaphthalene — iodonitrotetrazolium chloride — water — chloroform system and its analytical application

The formation of a new ternary ion-associate complex of vanadium(V) with 2,3-dihydroxynaphthalene and iodonitrotetrazolium chloride with a composition ratio of 1:2:1 is reported. The complex is quantitatively extracted from water into chloroform. The molar absorptivity (ɛ) of the extract at λ _max=340 nm is 2.5 × 10⁴ dm³/mol cm, and Beer’s law is obeyed for concentrations ranging from 0.1 to 0.9 μg/cm³ V(V). The following constants are determined: the extraction constant, the association constant, the distribution constant, and the recovery factor. The effects of foreign ions and reagents are studied. A selective and sensitive method is developed for determination of vanadium in steels.