CuZnAl水滑石衍生催化剂上甲醇水蒸气重整制氢Ⅰ. 催化剂焙烧温度的影响

 以类层柱CuZnAl水滑石为前体,经不同温度焙烧制备了一系列甲醇水蒸气重整制氢催化剂. 在250 ℃、 水/甲醇比1.3和重时空速2.5 h-1下的反应结果表明, 600 ℃焙烧的催化剂具有优异的活性和稳定性,而≤500 ℃和≥700 ℃焙烧后的催化剂活性较差. 热重、 X射线衍射、 傅里叶变换红外光谱和程序升温还原分析结果表明, 600 ℃焙烧时水滑石分解较为完全,析出纳米CuO粒子的同时伴生CuAl2O4尖晶石相,进而在反应过程中对金属Cu纳米粒子和ZnO起到良好的隔离和稳定作用. 焙烧温度≥700 ℃时CuO纳米粒子发生二次团聚,同时CuAl2O4尖晶石相大量生成,造成催化活性位减少,活性较低; 而焙烧温度≤500 ℃时水滑石分解不完全,生成 (Cu,Zn)AlxOy(CO3)z复合物且无尖晶石相伴生,造成反应中金属Cu纳米粒子和ZnO聚集,导致催化剂活性较低.     

醋酸H2O精馏中萃取剂的计算机辅助筛选

醋酸H2O精馏中萃取剂的计算机辅助筛选;Flash;萃取剂筛选;萃取精馏;醋酸     

有机液体化学试剂馏程测定注意事项

对有机液体化学试剂馏程测定过程中应注意的一些问题如加热源选择、蒸馏速度控制、温度计选择、蒸馏收率以及同一样品不同特性测量结果的相关性分析等进行了分析，为正确测定馏程提供经验和依据。     

湿混法制备甲醇氧化重整制氢CuZnAlZr催化剂

用简易湿混法制备了用于甲醇氧化重整制氢的CuZnAlZr催化剂,与共沉淀法制备的催化剂比较,结果表明,湿混法制备的催化剂具有相当的中高温活性和略低的低温活性,有较高的CO2选择性。XRD、TPR、TG-DSC等表征结果显示,湿混法制备的催化剂中铜组分易于向表面迁移和富集,并可能与氧化铝作用生成铜铝复合氧化物,具有了更高的Cu分散度和Cu0比表面浓度。湿混法制备的催化剂对甲醇氧化重整反应有较好的稳定性,经100 h的连续反应,在275 ℃时甲醇转化率在90％以上,重整气中氢气体积分数大于60％,CO2选择性接近99％。     

蜂窝催化剂上甲醇自热重整制氢的动力学研究

400 ℃～460 ℃,400 h－1～1 600 h－1,O2/CH3OH(mol ratio)=0.10～0.25,H2O/CH3OH (mol ratio) =1.0～1.8下,通过正交实验设计方法,用BSD-2A型内循环无梯度反应器研究了Zn-Cr/CeO2-ZrO2蜂窝催化剂上甲醇自热重整制氢反应的宏观动力学。以甲醇水蒸气重整反应、甲醇分解反应和甲醇完全氧化反应为独立反应进行了研究,得出了幂指数型反应速率表达式,并根据实验结果,利用最小二乘法求解了动力学参数值。F检验表明该动力学模型是高度显著的。该多重反应动力学方程的得出为蜂窝反应器的进一步模拟、优化和设计提供了数据。     

Evaluation of tocopherol recovery through simulation of molecular distillation process

DISMOL simulator was used to determine the best possible operating conditions to guide, in future studies, experimental works. This simulator needs several physical-chemical properties and often it is very difficult to determine them because of the complexity of the involved components. Their determinations must be made through correlations and/or predictions, in order to characterize the system and calculate it. The first try is to have simulation results of a system that later can be validated with experimental data. To implement, in the simulator, the necessary parameters of complex systems is a difficult task. In this work, we aimed to determe these properties in order to evaluate the tocopherol (vitamin E) recovery using a DISMOL simulator. The raw material used was the crude deodorizer distillate of soya oil. With this procedure, it is possible to determine the best operating conditions for experimental works and to evaluated the process in the separation of new systems, analyzing the profiles obtained from these simulations for the falling film molecular distillator.     

Spectrophotometric determination of boron in complex matrices by isothermal distillation of borate ester into curcumin

In situ distillation of borate ester into the curcumin solution has been developed for the spectrophotometric determination of boron in a variety of complex matrixes. A polypropylene vessel containing the sample solution was placed inside a vessel (PP) containing 10 ml of curcumin solution and the distillation was carried out at room temperature/on a water bath. The borate ester collected in to the curcumin solution was evaporated to dryness on the water bath, taken in acetone and the absorbance was measured at 550 nm. In situ distillation of borate ester directly into the chromogenic reagent eliminates tedious sample treatment (before and/or after borate separation), use of methanol, complicated quartz set up, possible loss of boron and reduces the analysis time significantly. In situ dehydration of sample solution by ethanolic vapour in the absence of dehydrating acid prevents the formation of fluoborate and co-distillation of potential anionic interferents (nitrate and fluoride). This developed method has been applied for the determination of traces of boric acid in boron powder by the distillation of methyl borate at room temperature. For other matrixes (water, uranium oxide, uranyl nitrate, fluoride salt, etc.) distillation of ethyl borate was carried out on the water bath. LOD (3σ) was 5 ng g⁻¹ for water and 30 ng g⁻¹ for solid samples.     

高性能纳米碳材料改性Cu/ZnO/Al2O3甲醇水蒸汽重整制氢催化剂

由铜基催化剂催化甲醇水蒸汽重整制氢是有效解决车载燃料电池等制氢需求的潜在途径．但传统铜基催化剂对该反应的低温催化活性及制氢选择性均不理想．近年来碳纳米管及活性碳纤维等因具有独特的纳米孔结构、高比表面积和优异的吸附性能作为潜在的新型催化材料而备受关注．     

乙醇水汽重整制氢反应中钯铜合金膜的透氢性能

 采用真空化学镀技术制备了厚度较薄的具有 fcc 结构的 Pd0.9Cu0.1/Al2O3 合金复合膜, 在 250~500 °C, 160~310 kPa 的乙醇水汽重整制氢模拟反应条件下, 考察了不同醇/水比的 H2-Ar-C2H5OH-H2O 混合气体系中该膜的透氢性能. 结果表明, 乙醇和水的存在均相同程度地降低了膜的透氢性能, 但测试条件下 Pd-Cu 合金膜仍保持完整的膜致密性和稳定的相结构. 在 500 °C, 310 kPa, H2-Ar-C2H5OH-H2O (H2:Ar:(C2H5OH+H2O) 体积比为 60:30:10) 混合气中, 膜的最大透氢量为 11.3 m3/(m2?h), H2 回收率大于 62.5%. Pd-Cu 合金膜在乙醇水汽重整制氢反应中具有潜在的应用前景.     

高温法和烘箱法测定水体中总氮的比较

分别采用烘箱法和高压蒸汽消解法对纯水和电解质溶液中的含氮有机化合物进行了消解,并用镉铜还原法测定了溶液中总氮的含量。实验表明,这两种消解方式无显著性差异,可以采用烘箱法代替压力蒸汽消毒器在电解质溶液中对含氮有机化合物进行消解,且烘箱法操作简单。