二元合金微观偏析的相场法数值模拟

使用耦合溶质场的相场模拟研究了Ni-Cu二元合金枝晶生长过程中固相溶质扩散系数D_s 对枝晶形貌和微观偏析等的影响.计算结果表明，随着D_s的减少，固液界 面前沿溶质扩散层越薄，枝晶生长越有利，枝晶尖端生长的速度越大，侧向分支越发达；D< sub>s越小，固相中溶质成分的波动越强烈，随着D_s的增大，固相中溶质 成分的波动相应减小；溶质微观偏析程度随D_s的增大而减小. 关键词： 相场方法 微观偏析 固相扩散系数 数值模拟     

Synthesis and characterization of poly(ethylene oxide‐co‐ethylene carbonate) macromonomers and their use in the preparation of crosslinked polymer electrolytes

Methacrylate‐functionalized poly(ethylene oxide‐co‐ethylene carbonate) macromonomers were prepared in two steps by the anionic ring‐opening polymerization of ethylene carbonate at 180 °C, with potassium methoxide as the initiator, followed by the reaction of the terminal hydroxyl groups of the polymers with methacryloyl chloride. The molecular weight of the polymer went through a maximum after approximately 45 min of polymerization, and the content of ethylene carbonate units in the polymer decreased with the reaction time. A polymer having a number‐average molecular weight of 2650 g mol^?1 and an ethylene carbonate content of 28 mol % was selected and used to prepare a macromonomer, which was subsequently polymerized by UV irradiation in the presence of different concentrations of lithium bis(trifluoromethanesulfonyl)imide salt. The resulting self‐supportive crosslinked polymer electrolyte membranes reached ionic conductivities of 6.3 × 10^?6 S cm^?1 at 20 °C. The coordination of the lithium ions by both the ether and carbonate oxygens in the polymer structure was indicated by Fourier transform infrared spectroscopy. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2195–2205, 2006     

Assessment of filtered gas–solid momentum transfer models via a linear wave propagation speed test

The propagation speeds of linear waves in gas–solid suspensions depend strongly on the solids volume fraction and the wave frequency. The latter is due to gas–solid momentum transfer and allows a simple test on filtered gas–solid momentum transfer models. Such models may predict linear wave propagation speeds different from those obtained with the non-filtered model at wave frequencies higher than the filter frequency, but not at wave frequencies lower than the filter frequency.     

Nd掺杂的Bi4Ti3O12变温X射线衍射分析

利用变温X射线衍射技术，在预烧过程中分析了Nd掺杂Bi4Ti3O12后生成Bi3.15Nd0.85Ti3O12（BNT）相的形成过程以及微结构的变化．实验观察到以30℃／min的升温速率，BNT相在700℃时开始形成，其衍射峰强度随温度的继续升高而增强，衍射峰半高宽随烧结时间延长而减小．X射线衍射分析结果表明，在900℃恒温条件下，烧结约2h，可形成单一的BNT相．     

Pulsed pump: Thermal effects in solid state lasers under super-Gaussian pulses

Solid state laser (SSL) powers can be realistically scaled when pumped by a real, efficient and multimode pulse. In this work, a fourth-order super-Gaussian pulse was assumed as a pump for SSL’s and a complete analytical expression for the thermal phase shift is given. Moreover, the focal length of thermal lens in paraxial ray approximation regime was studied. The results when applied to a Ti: sapphire crystal show an appreciable correction for abberation compared to a top-hat pulse.     

Mechanical analysis on rocket propellants

The mechanical properties of solid rocket propellants are very important for good functioning of rocket motors. During use and storage the mechanical properties of rocket propellants are changing, due to chemical and mechanical influences such as thermal reactions, oxidation reactions or vibrations. These influences can result in malfunctioning, leading to an unwanted explosion of the rocket motor. Most of modern rocket propellants consist of a polymer matrix (i.e. HTPB) filled with a crystalline material (i.e. AP, AN). However, the more conventional double base propellants consist of a solid gel matrix with additives, such as stabilizers. Both materials show a mechanical behaviour, quite similar to that of general polymers. To describe the material behaviour of both propellants a linear visco-elastic theory is often used to describe the mechanical behaviour for small deformations. Because the time-temperature dependency is also valid for these materials a mastercurve can be constituted. With this mastercurve the response properties (stiffness) under extreme conditions can be determined. At TNO-PML a mastercurve of a double base propellant was constituted using dynamical mechanical analysis (DMA) and compared with a mastercurve reduced from conventional (static) stress relaxation tests. The mechanical properties of this double base propellant determined by DMA were compared with conventional (quasi-static) tensile test results. This revised version was published online in July 2006 with corrections to the Cover Date.     

LiCoO2中锂离子固相扩散系数随循环次数的变化

The solid diffusion coefficient of lithium-ion in LiCoO₂ cathode material has been investigated by the capacity intermittent titration technique (CITT) at different voltages and at different charge/discharge cycles. By SEM, XRD and FTIR techniques, the structure of LiCoO₂ was studied before and after charge-discharge cycles, and the relationship between solid diffusion coefficient and crystal structure was further discussed. CITT results show that the value of Li⁺ solid diffusion coefficient of LiCoO₂ is about 10^-12 cm²·s^-1. During the whole charge-discharge cycles, the Li⁺ solid diffusion coefficient decreased within the voltage of 4.0～4.3 V, which is attributed to the change of the structure of LiCoO₂.     

WS2 超细粉体的固相法合成

WS2 超细粉体的固相法合成;WS2;固相反应;过硫系数;高能球磨;粒度