步进扫描时间分辨光谱及其在太阳电池光电导上的应用

建立傅里叶变换步进扫描时间分辨光电导光谱，并研究太阳电池中与转换效率密切相关的少数载流子寿命.实验选取三种典型的硅太阳电池(单晶硅样品1、多晶硅样品2和多晶硅样品3 )，发现其瞬态光电导的上升和衰退曲线可以分别用两个简单的指数函数描述.由于有复合中心的参与，复合过程中少数载流子的寿命比产生过程中的寿命短.为验证实验结果的可靠性，采用了提取样品少数载流子的体寿命和计算其有效扩散长度两种方法.通过与太阳电池暗伏安特性和负载特性研究相结合，进一步分析和讨论了少数载流子寿命与短路电流、开路电压和转换效率的关系.同时探讨了步进扫描时间分辨光谱实验的其他用途. 关键词： 步进扫描 时间分辨 硅太阳电池 瞬态光电导     

轻质建筑中定形相变内隔墙板冬季应用效果研究

现代轻质建筑热容较小,窗墙比较大,冬季在利用透射太阳辐射采暖的同时易造成室内温度波动过大。本文提出将定形相变蓄能板安装在建筑内隔墙表面,以增加建筑热容,减小室温波动。采用经实验验证程序,模拟分析了相变板热物性、表面换热系数和用量对冬季室内温度波动的影响,给出了北京地区相变内隔墙房间的设计原则。     

An investigation on planar dielectric light collectors for illumination and solar energy applications

In this paper the performances of inhomogeneous dielectric slabs as solar light collectors for both illumination and solar energy applications are analysed.     

Possible triggering of solar activity to big earthquakes (Ms ≥ 8) in faults with near west-east strike in China

A big earthquake (Ms = 8.1) occurred at western Kunlun Mts gap on November 14, 2001. It is the biggest earthquake in China in the past 50 years and the only one with a magnitude bigger than 8 in China after Dangxiong Earthquake (M = 8) in Tibet in 1951. The big earthquake has drawn wide attention of scientists in seismological, geophysical, geological and astro-geodynamic circles. Scientists are interested in the occurrence regularity of the very big earthquakes and try to find out the fac…     

蓄能型液体除湿冷却空调系统的建立与实验研究

本文提出了一种蓄能型液体除湿蒸发冷却空调系统的设计方案,并基于此方案搭建了一个制冷量为3 kW的蓄能型液体除湿蒸发冷却空调系统实验台。通过电加热器模拟60~80℃的低品位热源(太阳能、发动机排气余热、工业余热等),以LiCl水溶液作为除湿溶液,主要研究了在系统稳定运行时,各环境参数对此除湿蒸发冷却空调系统性能系数COP的影响情况。     

Al2O3钝化及其在晶硅太阳电池中的应用

介绍了Al₂O₃的材料性质及其原子层沉积制备方法, 详细阐述了该材料的钝化机制(化学钝化和场效应钝化), 并从薄膜厚度、热稳定性及叠层钝化等角度阐释其优化方案. 概述了Al₂O₃钝化在晶体硅太阳电池中的应用, 主要包括钝化发射极及背面局部扩散电池和钝化发射极及背表面电池. 最后, 对Al₂O₃钝化工艺的未来研究方向和大规模的工业应用进行了展望.     

19.4%‐efficient large‐area fully screen‐printed silicon solar cells

We demonstrate industrially feasible large‐area solar cells with passivated homogeneous emitter and rear achieving energy conversion efficiencies of up to 19.4% on 125 × 125 mm² p‐type 2–3 Ω cm boron‐doped Czochralski silicon wafers. Front and rear metal contacts are fabricated by screen‐printing of silver and aluminum paste and firing in a conventional belt furnace. We implement two different dielectric rear surface passivation stacks: (i) a thermally grown silicon dioxide/silicon nitride stack and (ii) an atomic‐layer‐deposited aluminum oxide/silicon nitride stack. The dielectrics at the rear result in a decreased surface recombination velocity of S_rear = 70 cm/s and 80 cm/s, and an increased internal IR reflectance of up to 91% corresponding to an improved J_sc of up to 38.9 mA/cm² and V_oc of up to 664 mV. We observe an increase in cell efficiency of 0.8% absolute for the cells compared to 18.6% efficient reference solar cells featuring a full‐area aluminum back surface field. To our knowledge, the energy conversion efficiency of 19.4% is the best value reported so far for large area screen‐printed solar cells. (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Understanding the junction degradation mechanism in CdS/CdTe solar cells using a Cd-deficient CdTe layer

It is known that CdTe solar cells are often degraded under solar illumination. But the degradation mechanism is not fully proved because it does not appear consistently. The junction degradation in CdS/CdTe solar cells was investigated using a CdTe layer with Cd deficient composition, where Cd vacancy concentration is high. It was found that the Cu atoms easily filled the Cd vacancies in CdTe and transport to junction area from Cu back contact. PL measurement and spectral quantum efficiency measurement showed that the incorporation of Cu atoms in CdS forms a defect energy level at 1.55 eV below the conduction band in CdS. As a result, the junction built-in potential is decreased and light penetration into CdTe absorber is shielded. For reliable and stable CdTe cells, the formation of Cd vacancy in CdTe should be avoided by careful control of CdTe.     

基于薄膜电极溶胶修饰的染料敏化太阳电池光电特性研究

染料敏化太阳电池(DSC)中的纳米薄膜电极 是决定太阳电池光电转换性能的重要组成部分. 为改善薄膜电极特性, 采用了不同浓度的TiO₂溶胶对DSC光阳极导电玻 璃和纳米TiO₂多孔薄膜进行不同方式的界面处理. 利用X射线衍射方法对制备得到的多孔薄膜以及溶胶经高温处理 后致密层中纳米TiO₂颗粒的尺寸及晶型进行了测试. 采用高分辨透射电子显微镜和场发射扫描电子 显微镜观察了纳米颗粒及薄膜微结构形貌. 采用强度调制光电流谱/光电压谱分析了TiO₂溶 胶的不同处理方式对电子传输和复合的影响. 在100 mW· cm^-2光强以及暗环境下分别测试了DSC的伏安输出性能以及暗电流. 结果表明, 不同浓度和处理方式均能较好地抑制暗电流. 溶胶处理后光生电子寿命τ_n延长, 电子传输平均时间τ_d相应缩短. 采用浓度为0.10 mol·L^-1的 溶胶对导电玻璃和多孔膜同时处理, DSC的宏观输出特性最佳, 短路电流密度J_sc提高了10.9%, 光电转换效率η提高了11.9%.     

Ag纳米颗粒对有机小分子太阳能电池性能的改善

在有机小分子太阳能电池CuPc/C60和TiOPc/C60的阳极ITO表面分别制备了一层Ag纳米颗粒,并采用MoO3作为阳极缓冲层,器件的性能均得到有效改善.Ag纳米颗粒的引入所形成的表面等离子激元共振可显著提高有机光活性层的吸收效率和光生激子的分解效率;而MoO3有效抑制了光生激子在有机/金属界面处发生的猝灭,提高了...