Mechanical behavior of films of miscible polyamide 6/polyamide 6I‐6T blends

The deformation behavior of miscible PA6/aPA blends films under uniaxial and biaxial tensile drawing has been investigated in relation to blend composition. Whatever be the composition, the initial crystalline structure is ill‐ordered and no evidence of spherulitic morphology was shown. At temperatures beyond the activation of the viscoelastic α relaxation, a ductility improvement upon addition of aPA has been revealed in both uniaxial and biaxial stretching. The decrease in the yield stress with increasing aPA content mainly originates from the reduction in crystal fraction. Regarding the observed evolution in ultimate drawability and strain hardening upon addition of aPA, the latter component of the blend is considered to act as a diluent of the macromolecular network, and the experimental data are fairly well accounted for according to Graessley's theory. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1690–1701, 2006     

Design and Implementation of a Fibre Channel Target Driver Supporting SCSI

Fibre channel storage area networks (FC-SAN) are effective solutions to address storage management problems caused by very large volumes of data. But the expense of fibre channel devices limits FC-SAN applications. The use of IP networks instead of fibre channel networks will reduce SAN cost, but will also reduce the performance. Therefore, small computer system interface (SCSI) devices were considered to replace FC disks to reduce the SAN cost. A driver for the FC network adapter and the FC target, designed and implemented to support this structure, obeys the SCSI protocol and works in target mode with 200 MB/s bandwidth. The FC target architecture and implementation were compared with the FC initiator.The SCSI command transfer process in the FC layer was described. The performance test results show that the maximum I/O throughput reachs 167 MB/s for read requests and 196 MB/s for write requests (FC bandwidth is 200 MB/s), verifying that the FC target is very efficient. The modularization, efficiency, and low cost of the FC target will enable SAN and fibre channel to be more widely used in applications.     

在高盐碱地区利用微区改土进行城市绿化

在盐碱地利用微区改土植树技术，对微区的土壤环境进行有效改良，创造有利于植物生长的立地条件，是在高盐碱地区进行城市绿化的一种行之有效地新方法。     

豆乳的乳酸菌发酵研究

从发酵酸牛乳手工业生产菌株中筛选出菌种活力高，产酸能力强的两株乳酸菌：ＨＬｂ（保加利亚乳杆菌）和ＨＳｔ（嗜热乳酸链球菌）二者协同作用，使酸豆乳的生产周期较以往资料所报道的缩短３７．５％，酸度提高２０％。     

软塑状土质隧道施工技术

通过对神延铁路羊马河隧道DK437 600～DK437 682长82m、七楞山隧道DK428 550～DK428 471长79m的软塑状黄土、羊马河隧道DK438 349～ 380长31m土质隧道塌方段的施工，总结了小管棚结合管桩快速通过软塑状土质隧道及土质隧道塌方地段的施工经验．     

Small ball probabilities for Gaussian processes with stationary increments under Hölder norms

Small ball probabilities are estimated for Gaussian processes with stationary increments when the small balls are given by various Hölder norms. As an application we establish results related to Chung's functional law of the iterated logarithm for fractional Brownian motion under Hölder norms. In particular, we identify the points approached slowest in the functional law of the iterated logarithm.Supported in part by NSF Grant DMS-9024961.     

方环形力传感器变形的边界元分析

本文对某方环形力传感器的变形进行了边界元分析，在此基础上确定了应变片的贴片部位及组桥方式．     

论村镇建设的安全质量问题

从几起房屋质量安全事故为案例,分析了事故产生的原因,指出了村镇建设中工程质量安全管理方面存在的问题,提出了提高村镇建设工程质量安全管理水平的建议。     

Long-term prediction of compressive creep development in expanded polystyrene

The results obtained in investigating the creep of expanded polystyrene (EPS) boards under compressive stress are presented. Power and exponential equations were used for describing creep compliance. It was found that the curves of creep compliance approximated by both equations adequately represent the research results, taking into account the scatter of the experimental data. Based on the calculation and empirical estimate of long-term creep of EPS under compressive stress σ_c=(0.25–0.45)σ_10%, its creep compliance was determined for a period of 10 years in the future. The dependence of on the density of polystyrene boards and the value of long-term compressive stress σ_c was established. The expected values of creep strain development in expanded polystyrene boards EPS 80–EPS 250 under constant compressive stress σ_c=(0.25–0.45)σ_10% are presented for the prediction period of 10 years. To obtain the expected creep values for any other period of time in the interval of 5T50 years, the values of should be multiplied by the empirical coefficient .