带空气腔芯轴型光纤水听器特性研究

对带空气腔芯轴型光纤水听器进行了研究和试验验证.分别建立了二维和三维模型对水听器性能进行分析,给出了两种模型下的水听器相移灵敏度计算公式;小批量制作了22个该结构的水听器并进行了测试.试验数据与模型计算结果十分吻合.结果表明,三维模型计算结果比二维模型更为准确,频带内均方根偏差大部分都小于0.3(dB·re·rad)/μPa.试验采用的水听器相移灵敏度为－153(dB·re·rad)/μPa,其归一化相移灵敏度达到－308(dB·re·1)/μPa.同时,该模型可以更好地根据实际需要来设计不同尺寸和性能的水听器结构.     

20 Hz~10 kHz光纤水听器相移灵敏度校准

利用相位生成载波解调技术精确测量光纤水听器的光相移量,在20 Hz~10 kHz频率范围实现了光纤水听器探头相移灵敏度的校准.20 Hz~1.25 kHz频段采用驻波管比较法进行校准,1.25 kHz~10 kHz频段采用自由场脉冲比较法进行校准.利用本文建立的校准系统,对TMD 35#光纤水听器的相移灵敏度进行校准,校准结果表明,两种方法测得的相移灵敏度具有很好的一致性,在1.25 kHz频率点的相移灵敏度值偏差为0.8 dB.不确定度分析表明,该校准系统的扩展不确定度(k=2)为0.9 dB.     

Fluorescence studies and semiempirical calculations on alkali ion indicators

Two newly synthesized cryptands act as sensitive Na⁺- and K⁺-selective indicators for cation concentrations above 20 M. The fluorescence properties change markedly upon cation binding. In addition, the free ligands exhibit a pronounced sensitivity to pH, which is considerably lower for the cation complexes. Time resolved fluorescence is characterized by a decay time of about 5 ns that is attributed to the diprotonated protolytic state of the uncomplexed ligands. Semiempirical calculations show the systematic influence of the nitrogen lone pairs or the N–H bond on the stability of the system. The cause of the strong fluorescence intensity increase observed upon protonation of the fluorescent cryptands may be attributed to an increase in the S₁–T _x energy gap as a consequence of bridgehead nitrogen protonation.This is a peer-reviewed conference proceeding article from the Third Conference on Methods and Applications of Fluorescence Spectroscopy, Prague, Czech Republic, October 18–21, 1993.     

关于《SZJ－10型沼泽检波器》主要技术指标的测试

作者受厂家委托，对美国制造的《ＳＺＪ－１０型沼泽检波器》的主要部件——《振荡探头》进行了有关技术参数的测试，测试结果基本符合实际，为生产厂家提供了测试方法和基本数据．本文《振荡钻探头》两个主要静态参数的测试方法做简单介绍。     

p型金属氧化物半导体场效应晶体管低剂量率辐射损伤增强效应模型研究

对一种非加固4007电路中p型金属氧化物半导体场效应晶体管(PMOSFET)在不同剂量率条件下的电离辐射损伤效应及高剂量率辐照后的退火效应进行了研究. 通过测量不同剂量率条件下PMOSFET的亚阈I-V特性曲线,得到阈值电压漂移量随累积剂量、退火时间的变化关系. 实验发现,此种型号的PMOSFET具有低剂量率辐射损伤增强效应. 通过描述H⁺在氧化层中的输运过程,解释了界面态的形成原因,初步探讨了非加固4007电路中PMOSFET低剂量率辐射损伤增强效应模型. 关键词： p型金属氧化物半导体场效应晶体管 60Co γ射线')" href="#">⁶⁰Co γ射线 电离辐射损伤 低剂量率辐射损伤增强效应     

用双灵敏度VISAR测量铜飞片自由面速度

 用双灵敏度VISAR干涉仪测量了在冲击波和爆轰波驱动下,铜飞片自由面的连续速度。干涉仪有两种条纹常数,每个条纹常数和相应的条纹计数同时用于产生一个速度历史。通过比较两个速度历史并结合其它条件,可以确定由于光电倍增管带宽限制而引起的条纹丢失的具体数目。     

Sensitivity improvement of aluminum-based far-ultraviolet nearly guided-wave surface plasmon resonance sensor

An aluminum (Al) based nearly guided-wave surface plasmon resonance (NGWSPR) sensor is investigated in the far-ultraviolet (FUV) region. By simultaneously optimizing the thickness of Al and dielectric films, the sensitivity of the optimized Al-based FUV-NGWSPR sensor increases from 183°/RIU to 309°/RIU, and its figure of merit rises from 26.47 RIU^-1 to 32.59 RIU^-1 when the refractive index of dielectric increases from 2 to 5. Compared with a traditional FUV-SPR sensor without dielectric, the optimized FUV-NGWSPR sensor can realize simultaneous improvement of sensitivity and figure of merit. In addition, the FUV-NGWSPR sensor with realistic materials (diamond, Ta₂O₅, and GaN) is also investigated, and 137.84%, 52.70%, and 41.89% sensitivity improvements are achieved respectively. This work proposes a method for performance improvement of FUV-SPR sensors by exciting nearly guided-wave, and could be helpful for the high-performance SPR sensor in the short-wavelength region.     

Tunable and highly sensitive temperature sensor based on graphene photonic crystal fiber

Optical fiber temperature sensors have been widely employed in enormous areas ranging from electric power industry, medical treatment, ocean dynamics to aerospace. Recently, graphene optical fiber temperature sensors attract tremendous attention for their merits of simple structure and direct power detecting ability. However, these sensors based on transfer techniques still have limitations in the relatively low sensitivity or distortion of the transmission characteristics, due to the unsuitable Fermi level of graphene and the destruction of fiber structure, respectively. Here, we propose a tunable and highly sensitive temperature sensor based on graphene photonic crystal fiber (Gr-PCF) with the non-destructive integration of graphene into the holes of PCF. This hybrid structure promises the intact fiber structure and transmission mode, which efficiently enhances the temperature detection ability of graphene. From our simulation, we find that the temperature sensitivity can be electrically tuned over four orders of magnitude and achieve up to ～ 3.34×10^-3 dB/(cm·℃) when the graphene Fermi level is ～ 35 meV higher than half the incident photon energy. Additionally, this sensitivity can be further improved by ～ 10 times through optimizing the PCF structure (such as the fiber hole diameter) to enhance the light-matter interaction. Our results provide a new way for the design of the highly sensitive temperature sensors and broaden applications in all-fiber optoelectronic devices.     

Modeling and testing of snow penetration

Penetration by a cone into snow is commonly used to characterize snow properties. However, the effects of the diameter and half-angle of the cone on the mechanical properties of snow have not been systematically studied. In addition, no estimation of material parameters in a physically-based model has been made such that the results from penetration provide only an index of snow properties. In this paper, modeling and experimental methods are used to examine the effects of cone geometry on the maximum penetration force and associated hardness, with penetrometers ranging from 2.5 to 4 mm in diameter, 15° to 45° in cone half-angle, and testing both fine-grained and coarse-grained snows. The material point method, in conjunction with the Drucker–Prager cap plasticity model, was used to obtain the theoretical penetration force-distance relationship. Global sensitivity studies were conducted that indicate that the cohesion accounts for 86% of the penetration force, followed distantly by friction angle which accounts for 27%. A general trend, for the simulation results was established: for a given half-angle, the penetration force increases with the increase of diameter which holds for most of the test data as well; for a given diameter, the penetration force decreases with the increase of half-angle, which holds for some of the test data. In addition, for a given half-angle, the hardness decreases with the increase of diameter; for a given diameter, the hardness decreases with the increase of half-angle. To take into consideration the uncertainty of test data, a simple interval-based metric was used to compare test data with simulation results; the comparison was satisfactory. The material parameters from the simulations can thus be considered as calibrated ones for the snow studied.     

AN EFFICIENT SEQUENTIAL DESIGN FOR SENSITIVITY EXPERIMENTS

In sensitivity experiments, the response is binary and each experimental unit has a critical stimulus level that cannot be observed directly. It is often of interest to estimate extreme quantiles of the distribution of these critical stimulus levels over the tested products. For this purpose a new sequential scheme is proposed with some commonly used models. By using the bootstrap repeated-sampling principle, reasonable prior distributions based on a historic data set are specified. Then, a Bayesian strategy for the sequential procedure is provided and the estimator is given. Further, a high order approximation for such an estimator is explored and its consistency is proven. A simulation study shows that the proposed method gives superior performances over the existing methods.