Effect of cold rolling process on microstructure and mechanical properties of high strength β titanium alloy thin sheets

The microstructure and mechanical properties of Ti-3.5Al-5Mo-6V-3Cr-2Sn-0.5Fe high strength titanium alloy sheets prepared by unidirectional cold rolling and two-step cross cold rolling were investigated. Results showed that the β phase grains were refined significantly by cold rolling followed by solution treatment for a short time.Compared to unidirectional cold rolling, the short time solution treatment after two-step cross rolling could significantly reduce the non-uniformity of the microstructure of the alloy sheets. After aging treatment at 550 ℃,the anisotropy of the mechanical properties still existed in the unidirectional rolled sheets, and the tensile strength was highest along the rolling direction. After solution and aging treatment, the anisotropy of the mechanical properties of the two-step cross rolling process sheet was not obvious than unidirectional cold rolling,and alloy had good strength and plasticity matching.     

Application of DEM modified with enlarged particle model to simulation of bead motion in a bead mill

We applied the discrete element method （DEM） of simulation modified by an enlarged particle model to simulate bead motion in a large bead mill. The stainless-steel bead mill has inner diameter of 102 mm and mill length of 198 mm. The bead diameter and filling ratio were fixed respectively at 0.5 mm and 85%. The agitator rotational speed was changed from 1863 to 3261 rpm. The bead motion was monitored experimentally using a high-speed video camera through a transparent mill body. For the simulation, enlarged particle sizes were set as 3-6 mm in diameter. With the DEM modified by the enlarged particle model, the motion of enlarged particles in a mill was simulated.The velocity data of the simulated enlarged particles were compared with those obtained in the experiment. The simulated velocity of the enlarged particles depends on the virtual frictional coefficient in the DEM model. The optimized value of the virtual frictional coefficient can be determined by considering the accumulated mean value. Results show that the velocity of the enlarged particles simulated increases with an increase in the optimum virtual frictional coefficient, but the simulated velocity agrees well with that determined experimentally by optimizing the virtual frictional coefficient in the simulation. The computing time in the simulation decreases with increased particle size.     

我国铁矿消费强度与钢铁冶炼及加工业的关系

简要分析了我国改革开放以来铁矿消费强度的阶段性变化特征,建立了铁矿消费强度的增量分解模型,应用国民经济投入产出表中数据,分时段对铁矿消费强度进行了增量分解计算和分析.结果表明,2002年前,资本形成以低于或基本等于GDP的增速增长,钢铁冶炼及加工业的铁矿消耗系数下降,致使铁矿消费强度降低;2002~2010年间,资本形成增速高于GDP增速,钢铁冶炼及加工业产出效益下降、铁矿消耗系数升高,致使铁矿消费强度大幅上升.因此,钢铁冶炼及加工业需要解决的主要矛盾是淘汰过剩的低端产能和推动产品结构升级,降低整个经济的铁矿消费强度,达到产业健康稳定发展的目的.     

基于数值积分与功率损耗测试的冷轧电机功率模型

为提高冷轧电机功率的计算精度,提出了一种新型的电机功率在线计算模型,模型中将电机功率分为轧制功率和机械功率损耗.其中,轧制功率采用基于简易有限元的数值积分方法计算获得,而电机机械功率损耗采用实验测试回归方法获得.基于本文设计的测试方案和模型结构,通过对某1 450 mm五机架冷连轧机组的现场测试,回归得到了功率损耗模型中的系数,并将其应用到了该机组中.现场实际应用表明该电机功率模型的计算偏差可控制在±5%以内,证明该模型具有较高的计算精度,符合现场控制要求,具有广泛的应用前景.     

基于条元法的异步轧制金属三维塑性变形分析

采用条元法分析了异步轧制条件下金属在变形区内的变形情况,建立了适用于异步轧制的轧制压力公式及中性点坐标公式,并在计算摩擦力时考虑了粘着区的存在。通过仿真分析,得到了异步轧制条件下变形区内摩擦力的分布规律及应力、应变的分布规律,最后分析了不同速比对等效应力的影响以及不同入口厚度对轧制压力的影响。     

歪斜安装对组配轴承转子系统动力学特性影响

针对多联组配轴承歪斜安装情况,推导了一个轴承外圈发生绕竖直方向歪斜时滚动轴承的非线性支承力形式,并借助Timoshenko梁轴单元建立了主轴模型,利用打靶法和Floquet理论分析了歪斜对系统全局非线性稳定特性和振动特性的影响。通过与正常安装组配轴承转子系统对比发现:外圈歪斜后系统在大间隙时的低转速区域容易出现倍周期分叉,在高转速区域易表现为伪周期分叉;在小间隙工况时容易获得大范围的周期运动参数区域。同时,歪斜使得系统的一临界峰峰值右移且明显放大,从而导致系统在高转速区域的水平方向振动明显增大。研究结果表明,掌握且合理利用轴承歪斜后的非均匀间隙特性,有助于改善系统运行的动力特性。     

Z-164D溶液对铝土矿强度的影响及其作用机理

以Z-164D为助磨剂，对广西田阳铝土矿进行了邦德球磨功指数试验和单轴抗压强度试验.结果表明:铝土矿经水和Z-164D溶液浸泡后，邦德球磨功指数分别下降了105%和379%，单轴抗压强度分别下降了2684%和4279%.红外光谱分析及X射线能谱微区元素分析表明，Z-164D只能在铝土矿表面发生物理和化学吸附，并不能够渗入铝土矿内部.建立了Z-164D溶液对铝土矿强度影响的作用机理模型，水分子与Z-164D相互促进，共同导致铝土矿缺陷程度增加、强度降低.     

Synergetic catalytic effect of rGO,Pd, Fe3O4 and PPy as a magnetically separable and recyclable nanocomposite for coupling reactions in green media

In this paper, rGO/Pd–Fe₃O₄@PPy as an efficient stable nanocomposite was synthesized. To understand the synergetic effects of rGO, Pd, Fe₃O₄ and PolyPyrrole, the performance of rGO/Pd–Fe₃O₄@PPy as a heterogeneous recyclable nanocatalyst in the green synthesis of C‐C and C‐O coupling products, as well as different conditions are studied. Synthesized rGO/Pd–Fe₃O₄@PPy was characterized by FT‐IR, XRD, FE‐SEM, EDS, TGA and AFM analysis. Best results are obtained under sonication in H₂O for C‐C coupling and by ball‐milling for C‐O coupling. The benefits of this method include: green solvents and conditions, absence of external base, low reaction times with high yield and easy work‐up method.     

Protein-Mediated Suppression of Rolling Circle Amplification for Biosensing with an Aptamer-Containing DNA Primer

We report a method to detect proteins via suppression of rolling circle amplification (RCA) by using an appropriate aptamer as the linear primer (denoted as an aptaprimer) to initiate RCA. In the absence of a protein target, the aptaprimer is free to initiate RCA, which can produce long DNA products that are detected via binding of a fluorescent intercalating dye. Introduction of a target causes the primer region within the aptamer to become unavailable for binding to the circular template, inhibiting RCA. Using SYBR Gold or QuantiFluor dyes as fluorescent probes to bind to the RCA reaction product, it is possible to produce a generic protein-modulated RCA assay system that does not require fluorophore- or biotin-modified DNA species, substantially reducing complexity and cost of reagents. Based on this modulation of RCA, we demonstrate the ability to produce both solution and paper-based assays for rapid and quantitative detection of proteins including platelet derived growth factor and thrombin.     

热模拟平面应变条件下的热轧织构研究

以微合金钢为材料,采用光学显微镜和EBSD,研究热模拟平面应变实验条件下再结晶奥氏体和变形奥氏体的织构演变.研究发现,在热模拟平面应变实验的压缩过程中,试样的两个自由端限制了变形区金属的宽向流动,达到了很好的平面应变状态.对于再结晶奥氏体相变工艺,由于相变前奥氏体发生再结晶,无畸变保留,奥氏体分解为仿晶界铁素体、贝氏体和少量的珠光体,织构为{100}011α;对于变形奥氏体相变工艺,未再结晶区的变形促进了铁素体相变,使奥氏体分解为铁素体和珠光体组织,织构为{332}113α和{113}110α.此两种工艺条件下的织构,皆为平面应变条件下的奥氏体相变织构,即热模拟平面应变实验可以达到很好的平面应变状态,可用于研究热轧过程的织构演变.