热连轧棒材三切分轧制的实践

介绍萍乡钢铁有限责任公司三轧厂引进的三切铲轧制技术、主要设备概况、生产过程中存在的问题及改进措施：分析三线切分轧制稳定生产的关键是保证切分后轧件尺寸的均匀性，并给出了预切分轧件的偏移量与三线活套高度差的关系。     

冷轧压下率分配对IF钢深冲性能的影响

冷轧压下率对IF钢的深冲性能有重要的影响。采用两次冷轧，在总压下率一定的情况下，两次冷轧压下率的分配是影响IF钢深冲性能的关键。通过冷轧实验，得出在总压下率一定时，两次冷轧比一次冷轧的塑性应变比r值要高；总压下率一定，一次冷轧压下率较小，两次冷轧压下率较大时，可使r值提高；同时，冷轧总压下率提高，也可使r值提高。     

轧制法生产高复基比不锈复合钢板和钢带的开发应用

不锈钢复合板既具有不锈钢的耐腐蚀性、耐磨性、抗磁性、豪华性和装饰性;又具碳钢良好的可焊性、成型性、拉延性和导热性,还可节约镍铬合金、降低成本,因而具有广阔的发展前景,值得大力推广应用.     

棒材切分轧制过程中三维弹塑性有限元模拟

采用三维弹塑性有限元法对棒钢三线切分轧制过程的金属变形区进行了模拟。通过建立数学模型和计算，对切分轧件的变形特征、应力与应变进行了分析，提出了预切孔金属流动变形的稳定性问题。如果预切孔内轧件的变形过大，切分楔附近的金属网格发生了很大的扭曲畸变，造成变形不均匀和金属的流动不稳定。根据模拟分析的结果，设计了直径为Φ12mm带肋钢筋的三线切分孔型系统，轧制生产实验结果表明：采用优化的新切分孔型系统进行生产，提高了轧机的生产率，改善了产品质量。     

CVC轧机的应用及技术问题分析

文章主要分析了CVC轧机的板形控制原理,应用中轴向力、磨损、轧辊热凸度及设备结构等技术问题。     

热轧层流冷却系统优化与模型参数自适应

针对热轧带钢卷取温度控制的不确定性和时变性, 利用系统优化与模型参数的自适应控制热输出辊道上带钢温度. 从控制模式、冷却策略、段跟踪和模型的再计算以及学习系数的读取等方面对系统进行了优化. 根据实际工艺状况, 实时采集现场数据对层冷模型中的参数进行自适应调整, 并就组别分类、空冷/水冷系数的回归分析进行了研究. 实践结果表明： 采用这种方法能满足现场需要, 卷取温度控制精度较高, 基本在-15～15 ℃范围内;控制效果和带钢性能良好.     

Influence of chemistry and hot rolling conditions on high permeability non-grain oriented silicon steel

This paper discusses the influence of chemical composition on the final electromagnetic properties in higher permeability material. Furthermore, the effect of the hot rolling practice and the end of austenite transformation temperature range on the hot band microstructure is described. The magnetic polarization J₅₀₀₀ better than 1.7 T, using hot rolling conditions 40 mm transfer bar thickness, finish mill entry temperature 1000 °C, and finishing temperature 800–840 °C and after decarburization heat treatment and grain growth treatment, was obtained.     

Identification of chlorinated sulfur compounds in pulp mill effluents by GC-MS and GC-AED

Summary Three chlorinated dimethyl sulfones and five chlorinated thiophenes have been identified in the alkaline extraction liquor from a bleach plant by gas chromatography with atomic emission detection (GC-AED) and with mass spectrometry (GC-MS). The information on elemental content obtained by GC-AED enabled a rapid screening of the sulfur compounds and provided important structural information complementary to the mass spectral data. Quantitation was accomplished by GC-AED based on universal calibration.     

平辊薄件轧制的刚塑性有限元计算

本文用钢塑性有限元方法,对平辊同步和异步薄件轧制进行了计算,求出力能参数、速度场和应力应变场,并对二者加以比较。之后,又对异步轧制的特征进行了分析。     

Enhancing the enzymatic hydrolysis of cellulosic materials using simultaneous ball milling

One of the limiting factors restricting the effective and efficient bioconversion of softwood-derived lignocellulosic residues is the recalcitrance of the substrate following pretreatment. Consequently, the ensuing enzymatic process requires relatively high enzyme loadings to produce monomeric carbohydrates that are readily fermentable by ethanologenic microorganisms. In an attempt to circumvent the need for larger enzyme loadings, a simultaneous physical and enzymatic hydrolysis treatment was evaluated. A ball-mill reactor was used as the digestion vessel, and the extent and rate of hydrolysis were monitored. Concurrently, enzyme adsorption profiles and the rate of conversion during the course of hydrolysis were monitored. α-Cellulose, employed as a model substrate, and SO₂-impregnated steam-exploded Douglas-fir wood chips were assessed as the cellulosic substrates. The softwood-derived substrate was further posttreated with water and hot alkaline hydrogen peroxide to remove >90% of the original lignin. Experiments at different reaction conditions were evaluated, including substrate concentration, enzyme loading, reaction volumes, and number of ball beads employed during mechanical milling. It was apparent that the best conditions for the enzymatic hydrolysis of α-cellulose were attained using a higher number of beads, while the presence of air-liquid interface did not seem to affect the rate of saccharification. Similarly, when employing the lignocellulosic substrate, up to 100% hydrolysis could be achieved with a minimum enzyme loading (10 filter paper units/g of cellulose), at lower substrate concentrations and with a greater number of reaction beads during milling. It was apparent that the combined strategy of simultaneous ball milling and enzymatic hydrolysis could improve the rate of saccharification and/or reduce the enzyme loading required to attain total hydrolysis of the carbohydrate moieties.