椭圆法用于阳极溶出伏安法测定微量银

用新物理量Ｖｏｐ的椭圆法对阳极溶出伏安法分析的含银离子浓度为１０＾５－１０＾－９ｍｏｌ／Ｌ的一系列溶液进行了研究。结果表明：光学方法与电化学方法所得分析结果相同；椭圆法可检测的浓度下限比电化学方法低一个数量级以上。而且测量的相对平均偏差也小于电化学方法。     

杂氮硅三环成环反应的研究

本文报导了与硅原子直接相连的有机基团(R)对杂氮硅三环成环速率的影响。利用气相色谱检测成环反应的产物之一——乙醇的生成速率和数量,并同与硅相连的R基团对成环反应速率的影响作比较。实验结果表明五种杂氮硅三环成环速度顺序为Cl_2CH—>ClCH_2—>ClCH_2CH_2CH_2—>CH_2=CH—>CH_3—,这与理论推断相符。     

Solid-state interactions and drug release of teicoplanin in binary combinations with peracetylated α-, β-, and γ-cyclodextrins

Triacetyl α-cyclodextrin, triacetyl β-cyclodextrin and triacetyl γ-cyclodextrin were tested as possible hydrophobic carriers to prolong the release of hydrophilic teicoplanin (TCP). Physical–chemical characterization of individual components, drug-carrier physical mixtures at 0.5, 0.67 and 0.75 mass fraction of carrier, and the respective interaction products by kneading or evaporative crystallization under microwave irradiation was carried out using differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). In vitro drug release in pH 7.4 phosphate buffer at 37 °C was determined by intrinsic dissolution rate (IDR) measurements on non disintegrating compressed discs. Solid-state interactions of TCP with triacetyl α-cyclodextrin by evaporative crystallization and kneading and with triacetyl β-cyclodextrin by evaporative crystallization (probably resulting in carrier amorphization) were demonstrated. The role of carrier hydrophobicity, carrier mass fraction and preparation method of solid drug-carrier combinations on solid-state drug-carrier interactions and slowing down of TCP release was assessed. Modulation of drug release can be achieved using TCP-triacetyl γ-cyclodextrin combinations at 0.5 mass fraction of carrier.     

Properties of ITO films prepared by reactive magnetron sputtering

Indium tin oxide (ITO) thin films were deposited by mid frequency pulsed dual magnetron sputtering using a metallic alloy target with 10 wt.% tin in an atmosphere of argon and oxygen. The aim of the work was to study the interdependence of structural, electrical and optical properties of ITO films deposited in the reactive and transition target mode, respectively. The deposition rate in the transition mode exceeds the deposition rate in the reactive mode by a factor of six, a maximum value of 100 nm·m min⁻¹ could be achieved. This corresponds to a static deposition rate of 200 nm min⁻¹. The lowest electrical resistivity of 1.1·10⁻³ Ω cm was measured at samples deposited in the high oxygen flow range in the transition mode. The samples show a good transparency in the visible range corresponding to extinction coefficients being below 10⁻². X-ray diffraction was used to characterise crystalline structure as well as film stress. ITO films prepared in the transition mode show a slightly preferred orientation in (211) direction, whereas films deposited in the reactive mode are strongly (222) oriented. Compared to undoped In₂O₃ all samples have an enlarged lattice. The lattice strain perpendicular to the surface is about 0.8% and 2.0% for films grown in the transition and the reactive mode, respectively. Deposition in the transition mode introduces a biaxial film stress in the range of −300 MPa, while stress in reactive mode samples is −1500 MPa.     

甲醇催化分解动力学之研究

甲醇的裂解产物为H_2与CO,故甲醇被视为一种方便、安全的贮氢材料,可作为汽油的代用燃料;其裂解气作为保护气氛可广泛应用于热处理工业。甲醇裂解有两种方法,高温热裂解(约930℃)与低温催化裂解(约300℃)由于低温催化裂解有诸多优点,在工业上的应用正在发展。     

钢坯磨削温度的若干试验研究

通过使用“可磨式”人工热电偶进行的不同条件下的磨削温度测量试验研究了钢坯磨削工件表层温度,结果表明钢坯被磨削表层温度分布与热强呈三角形分布时的理论分析结果相同,表层峰值温度随磨削压力及磨削功率增大而提高,且随工件进给速度提高而略有降低,峰值温度还随磨削角度减小而提高,90°磨削的峰值温度比0°磨削要低250℃左右,砂轮种类也对峰值温度有重要影响,使用锆刚玉砂轮时磨削温度低于棕刚玉砂轮,试验结果表明高效钢坯磨削的磨削区温度远比普通磨削为高,可达1200℃左右,还从不同方面探讨了磨削高温对钢坯磨削的影响,认为尽管磨削高温有若干不利影响,但对高效钢坯磨削却是重要条件,上述讨论,从一个方面揭示了钢坯磨削机理,并验证了关于钢坯磨削温度的理论分析结果。     

The crystallization characteristics of polypropylene and low ethylene content polypropylene copolymer with copolyesters

The crystallization characteristics of polypropylene (PP) and low ethylene content PP copolymers with and without nucleating agents were studied by differential scanning calorimetry (DSC). PP and PP copolymers was blended with three different kinds of co[poly(butylene terephthalate-p-oxybenzoate)] copolyesters, designated B28, B46, and B64, with the copolyester level varying from 5 to 15 wt.%. All samples were prepared by solution blending in hot xylene solvent at 50 °C. The crystallization behavior of samples was then studied by DSC. The results indicate that these three copolyesters accelerate the crystallization rate of PP and PP copolymers in a manner similar to that of a nucleating agent. The acceleration of crystallization rate was most pronounced in these blend systems with a maximum level at 5 wt.% of B28. The observed changes in crystallization behavior are explained by the effect of the composition and the amount of copolyester in the blends.     

Sorption properties of freshly precipitated alumogels

The influence of the pH of precipitation and the ionic medium nature on the composition, surface charge, and kinetic sorption characteristics of aluminum oxyhydroxides formed by alkaline hydrolysis of an aqueous solution of aluminum nitrate was studied. The methods of drop titration with alkali, argentometric titration, point of zero charge, and indicator reactions of heterogeneous hydrolysis were used. The composition of the freshly precipitated hydrogels of aluminum(iii) oxyhydroxide, rate constants of heterogeneous hydrolysis of the IrCl₆ ^2– ions as indicator reactions, and the pH of the point of zero charge were determined. The rate of indicator reactions (as for other oxyhydroxide hydrogels) depends strongly on the pH of precipitation. However, it is lower than the rates characteristics of iron(iii) and chromium(iii) oxyhydroxides obtained under similar conditions. The pH of the point of zero charge for the alumogels in a chloride medium is 8.3 and that in a sulfate medium is 9.5.     

SYNTHESIS AND PHOTOCHROMISM OF ACRYLIC ESTER COPOLYMERS BEARING PENDANT VIOLOGEN GROUPS

A series of acrylic ester copolymers with viologen group as pendant were synthesizedthrough the reaction of MMA-EBA (Ethenyl bromoacetate) copolymer with 4-(4'-pyridyl)-N-alkyl (or arylalkyl) pyridiniums. These viologen copolymers can exchange their anionwith NH_4PF_6 in methanol to improve their solubility in organic solvents such as DMFand acetone. Compared with the corresponding low molecular viologens, these viologencopolymers have relatively lower color development rate under UV light and fade fasterin air due to less affinity to photo-reductant and deficiency of association between theircation radicals. Their photofatigue resistant ability is also slightly better than that of lowmolecular vinlogens.     

Dependence of the rate constants on the treatment of internal rotation modes: the reaction OH + CH3SH --> CH3S + H2O as an example

The title reaction has been used as an example to test the importance of using a hindered rotor treatment instead of a harmonic oscillator model for calculating vibrational partition functions corresponding to low-frequency internal rotation modes. First, a normal-mode analysis according to the Ayala and Schlegel's algorithm has been used to identify the internal rotation modes of methanethiol and the transition state structure. Then, after calculation of the energy barrier for each internal rotation, the corresponding hindered rotor partition functions have been calculated following the CW scheme of Chuang and Truhlar. The results show that the anharmonic treatment produces a rather modest improvement of the rate constants at room temperature or below.