Study on the Superhydrophilicity of the SiO2-TiO2 Thin Films Prepared by Sol-Gel Method at Room Temperature

Nanoscale SiO₂-TiO₂ composite thin films with the thickness of about 100 nm were prepared by sol-gel method at room temperature in air. The chemical states of the elements on the surface and near the surface were measured by XPS. The results showed that the Ti on/near the surface of the thin films existed not only as TiO₂ but also as Ti₂O₃. Part of the TiO₂ was changed to Ti₂O₃ after UV irradiation. The crystalline structure of the TiO₂ in the SiO₂-TiO₂ thin films was anatase with the crystallite size of 14–20 nm. It was found that the thin film prepared at room temperature in air has good superhydrophilic property and has strong adherence to the substrate.     

Electrospinning of ultrafine cellulose acetate fibers: Studies of a new solvent system and deacetylation of ultrafine cellulose acetate fibers

Electrospinning of cellulose acetate (CA) in a new solvent system and the deacetylation of the resulting ultrafine CA fibers were investigated. Ultrafine CA fibers (∼2.3 μm) were successfully prepared via electrospinning of CA in a mixed solvent of acetone/water at water contents of 10–15 wt %, and more ultrafine CA fibers (0.46 μm) were produced under basic pH conditions. Ultrafine cellulose fibers were regenerated from the homogeneous deacetylation of ultrafine CA fibers in KOH/ethanol. It was very rapid and completed within 20 min. The crystal structure, thermal properties, and morphology of ultrafine CA fibers were changed according to the degree of deacetylation, finally to those of pure cellulose, but the nonwoven fibrous mat structure was maintained. The activation energy for the deacetylation of ultrafine CA fibers was 10.3 kcal/mol. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 5–11, 2004     

Novel fixed‐site–carrier polyvinylamine membrane for carbon dioxide capture

Fixed‐site–carrier membranes were prepared for the facilitated transport of CO₂ by casting polyvinylamine (PVAm) on various supports, such as poly(ether sulfone) (PES), polyacrylonitrile (PAN), cellulose acetate (CA), and polysulfone (PSO). The cast PVAm on the support was crosslinked by various methods with glutaraldehyde, hydrochloric acid, sulfuric acid, and ammonium fluoride. Among the membranes tested, the PVAm cast on polysulfone and crosslinked by ammonium fluoride showed the highest selectivity of CO₂ over CH₄ (>1000). The permeance of CO₂ was then measured to be 0.014 m³ (STP)/(m² bar h) for a 20 μm thick membrane. The effect of the molecular weight of PVAm and feed pressure on the permeance was also investigated. The selectivity increased remarkably with increasing molecular weight and decreased slightly with increased pressure in the range of 1 to 4 bar. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4326–4336, 2004     

Statistical thermodynamics evaluation of polymer–polymer miscibility

The Simha and Somcynsky (S–S) statistical thermodynamics theory was used to compute the solubility parameters as a function of temperature and pressure [δ = δ(T, P)], for a series of polymer melts. The characteristic scaling parameters required for this task, P*, T*, and V*, were extracted from the pressure–temperature–volume (PVT) data. To determine the potential polymer–polymer miscibility, the dependence of δ versus T (at ambient pressure) was computed for 17 polymers. Close proximity of the δ versus T curves for four miscible polymer pairs: PPE/PS, PS/PVME, and PC/PMMA signaled the usefulness of this approach. It is noteworthy, that the tabulated solubility parameters (derived from the solution data under ambient conditions) propounded the immiscibility of the PVC/PVAc pair. The computed values of δ also suggested miscibility for polymer pairs of unknown miscibility, namely PPE/PVC, PPE/PVAc, and PET/PSF. In recognizing the limitations of the solubility parameter approach (the omission of several thermodynamic contributions), these preliminary results are auspicious because they indicate a new route for estimating the miscibility of any polymeric material at a given temperature and pressure. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2909–2915, 2004     

光参量啁啾脉冲饱和放大的增益稳定性

 光参量啁啾脉冲放大（OPCPA）在饱和放大区存在一个增益稳定点，据此设计了一个输出稳定的三级OPCPA系统；第一、二、三级分别选用准相位匹配的周期极化钛氧磷酸钾（PPKTP）晶体、LBO晶体和KDP晶体作为增益介质。饱和放大时，增益随泵浦光强度变化时的增益输出稳定性明显改善，在泵浦光强度抖动低于6%的情况下，各级光参量放大器OPA输出的增益抖动小于1%。前级采用准相位匹配的PPKTP晶体作为增益介质，在远低于破坏阈值的30MW/cm²的泵浦功率密度下，可得到2×10⁵的饱和放大增益和20%的能量转换效率。     

介质靶表面的充电效应对等离子体浸没离子注入过程中鞘层特性的影响

针对等离子体浸没离子注入技术在绝缘体表面制备硅薄膜工艺，采用一维脉冲鞘层模型描述介质靶表面的充电效应对鞘层厚度、注入剂量及靶表面电位等物理量的影响.数值模拟结果表明：随着等离子体密度的增高，表面的充电效应将导致鞘层厚度变薄、表面电位下降以及注入剂量增加，而介质的厚度对鞘层特性的影响则相对较小. 关键词： 等离子体浸没离子注入 脉冲鞘层 绝缘介质 充电效应     

电子束蒸发制备HfO_2高k薄膜的结构特性

使用高真空电子束蒸发在p型Si(1 0 0 )衬底上制备了高kHfO2 薄膜 .俄歇电子能谱证实薄膜组分符合化学配比 ;x射线衍射测量表明刚沉积的薄膜是近非晶的 ,高温退火后发生部分晶化 ;原子力显微镜和扫描电子显微镜检测显示在高温退火前后薄膜均具有相当平整的表面 ,表明薄膜具有优良的热稳定性 ;椭偏测得在 6 0 0nm处薄膜折射率为 2 0 9;电容 电压测试得到的薄膜介电常数为 1 9.这些特性表明高真空电子束蒸发是一种很有希望的制备作为栅介质的HfO2 薄膜的方法     

高压增氧T′相R_2CuO_(4+δ)(R=Nd～Tm)低温磁性研究

T′相R2CuO4稀土铜氧化合物由于尺度效应而产生弱铁磁性行为已经被人们关注,报导了通过高温高氧压(6GPa,1000℃)合成稀土T′相R2CuO4(R=Nd,Sm,Eu,Gd,Tb,Dy,Ho,Er和Tm)化合物的结构和磁学性能。磁化率曲线显示,在低温下所有的高压增氧R2CuO4样品都出现新的低温弱铁磁性反常行为,转变温度在28K附近。新的低温弱铁磁性行为是由于CuO2面上微量氧空穴的掺入,使处于反铁磁有序CuO2面形成局域化的铁磁性团簇造成。实验证明新发现的低温弱铁磁性行为与尺度效应产生弱铁磁性行为属于完全不同的物理机制。结果还预示T′相R2CuO4稀土铜氧化合物很难通过空穴掺杂而实现超导。     

三维光晶格中玻色凝聚气体基态波函数及干涉演化

基于Gross-Pitaevskii方程，运用有效化学势概念，研究了囚禁在组合势(由磁阱和三维光 晶格组成)中玻色凝聚气体在三维光晶格中的分布规律，并由此得到玻色凝聚气体的归 一化基态波函数.在取消组合势和仅取消光晶格而保留磁阱的两种情况下，运用传播子方 法求解出玻色凝聚气体密度分布的解析表达式.取消组合势后，理论计算所得到的玻色凝聚 气体聚随时间的演化规律与Greiner等的实验结果相一致.仅取消光晶格而保留磁阱时，研 究表明玻色凝聚气体的干涉模式呈现周期性的振荡行为.此外，在磁阱为各向异性的情况下 ， 关键词： 玻色凝聚气体 磁阱 光晶格 干涉模式     

聚乙烯基咔唑与Alq3混合薄膜的发光性能与能量传递过程

研究了Alq3与聚乙烯基咔唑(PVK)按不同比例的混合体系制备的薄膜的发光特性.通过对混合薄膜的吸收光谱、激发光谱和发射光谱的分析，研究了PVK与Alq3之间的 能量传递规律.当Alq3与PVK的质量比为1∶7时，能量传递效率最高.用一个由单链模 型扩展到包括杂质的哈密顿量对实验进行模拟，发现该模型能够较好地解释有关的实验结果. 关键词： 吸收光谱 激发光谱 发射光谱 能量传递