激光溅射Ni等离子体与气相CH3OH团簇的反应

用激光溅射 分子束技术研究了气相中Ni的等离子体与甲醇分子团簇的反应 .观察到Ni+ (CH3 OH) n、NiO+ (CH3 OH) n、H+ (CH3 OH) n、H3 O+ (CH3 OH) n 四个种类的团簇正离子和CH3 O-(CH3 OH) n(n≤ 2 5 )一种团簇负离子 .详细考察了激光烧蚀等离子体作用于脉冲分子束的不同位置时 ,对团簇产物种类和团簇尺寸大小的影响 .发现NiO+ (CH3 OH) n 是由Ni+ (CH3 OH) n 团簇内的脱甲烷反应生成的 ,而H+ (CH3 OH) n、H3 O+ (CH3 OH) n主要是激光等离子体中的电子与甲醇团簇碰撞电离产生的     

某些类氖离子和类镍离子等离子体状态对应关系的研究

利用一维拉格朗日流体动力学程序Med103详细研究了产生类镍Ag,Cd,In,Sn, Sb离子和类氖Fe,Co,Ni,Cu,Zn离子的等离子体状态.通过对电子温度、离子丰度、离子数密度等状态参量的分析比较，得到了这两类等离子体状态之间的对应关系.即类镍银的等离子体状态与类氖铁 的相近，类镍镉的与类氖钴的相近，依次类推.利用这一对应关系可以方便地由类氖机理x射线激光的等离子体状态来对相应元素的类镍x射线激光的等离子体状态进行判断. 关键词： 类氖 类镍 等离子体状态 x射线激光     

Microstructure and high-temperature wear resistance of a laser surface alloyed γ-TiAl with carbon

TiC reinforced composite coating on γ-TiAl alloy was successfully fabricated by laser surface alloying with carbon. The fine TiC reinforcing phase had a gradient distribution in the coating, and its growth morphology of TiC in laser surface alloyed coating was in unique faceted platelet-like. The composite coating exhibited high hardness and excellent high-temperature sliding wear resistance.     

Load-Carrying Capacity of Circular Plates Made of a Fiber-Reinforced Composite

The load-carrying capacity of circular plates made of a fiber-reinforced composite and loaded with axisymmetric transverse forces under axisymmetric boundary conditions is investigated. The plates can be freely supported or clamped along their contour. To the known yield condition used, in the plane of main bending moments, there correspond irregular hexagons, which depend on the mechanical properties of composite constituents and some characteristic geometrical parameters. It is shown that, depending on the ratio of ultimate radial and circumferential bending moments, in the plastic state, the circular plates (the central part of the clamped plates) take the form of a cone or a frustum of cone. For each of the cases, the limit load is found, which is a function of the above-mentioned mechanical parameters. The statically allowable fields of bending moments and the corresponding allowable fields of deflection rates are determined. The solutions found are exact. Special cases for the freely supported plates are analyzed, and the results obtained are presented in the form of graphs.__________Translated from Mekhanika Kompozitnykh Materialov, Vol. 41, No. 2, pp. 177–192, March–April, 2005.     

制备介孔复合环境材料的酸洗刻蚀工艺

探索了一种制备介孔复合环境材料的方法--破坏式造孔与有机复合相结合,使最终产品可大量吸附污染水体中的各种污染物并具有一定的杀菌功能.该方法通过酸洗刻蚀,达到了去除原材料中的杂质和刻蚀孔径的目的,所制备的中间产品24h吸湿率为原材料的2倍,染料吸附量为原材料的1.6倍.     

CRP复合材料板复合型裂纹扩展方向预测理论研究

本文对碳纤维增强的复合材料板裂纹扩展方向预测理论进行了研究。介绍了最新发展起来的复合材料Z断裂理论 ,并通过试验证明了新理论的正确性     

集中荷载下叠合梁抗剪强度

本文对低叠合面钢筋破简支在合梁二阶段受力的斜截面抗剪性能进行了试验研究，并运用非线性有限元分析和试验实测数据，得出了一个适合于集中荷载下高低叠合面叠合梁的抗剪强度计算公式．     

电磁相分离法制备自生表层复合材料

采用电磁相分离法制备出以初生富铁相（AlSiFeMn复杂金属间化合物）为增强相，表层硬度为HB62．25，基体硬度为HB59．00的Al-11.70%Si-1.20?-1.50%Mn合金自生表层复合材料，增强相的显微硬度为HV 842。87，大小为20－80μm，该表层复合材料同基体材料相比，耐磨性提高了57．41％，所用方法工艺过程简单，成本低，为解决材料在服役环境中不同部位，不同性能的问题提供了新途径。     

强直电流伸展弧CVD硬质合金金刚石涂层工具

采用自行研制的强电流直流扩展电弧设备对酸浸和渗硼预处理的YG6刀片进行了金刚石薄膜涂层沉积，并对放于不同位置的沉积刀片表面涂层的激光Raman谱和SEM形貌进行了分析、研究。结果表明：渗硼预处理工艺优于酸浸预处理工艺；在渗硼处理的GY6刀片上，沉积的金刚石薄膜涂层具有大面积、均匀性好和质量高的特点。     

Charge density fluctuation of low frequency in a dusty plasma

The charge density fluctuation of low frequency in a dusty plasma, which is derived from the longitudinal dielectric permittivity of the dusty plasma, has been studied by kinetic theory. The results show that theP value, which describes the relative charge density on the dust in the plasma, and the charging frequency of a dust particle Ω _c , which describes the ratio of charge changing of the dust particles, determine the character of the charge density fluctuation of low frequency. For a dusty plasma ofP≪1, when the charging frequency Ω _c , is much smaller than the dusty plasma frequency ω_d, there is a strong charge density fluctuation which is of character of dust acoustic eigenwave. For a dusty plasma ofP≫1, when the frequency Ω _c , is much larger than ω _d there are weaker fluctuations with a wide spectrum. The results have been applied to the ionosphere and the range of radius and density of dust particles is found, where a strong charge density fluctuation of low frequency should exist.