Low dielectric thermoset. II. Synthesis and properties of novel 2,6‐dimethyl phenol–dipentene epoxy

A 2,6‐dimethyl phenol–dipentene adduct was synthesized from dipentene (DP) and 2,6‐dimethyl phenol, and then a 2,6‐dimethyl phenol–DP epoxy was synthesized from the reaction of the resultant 2,6‐dimethyl phenol–DP adduct and epichlorohydrin. The proposed structures were confirmed by Fourier transform infrared, elemental analysis, mass spectra, NMR spectra, and epoxy equivalent weight titration. The synthesized 2,6‐dimethyl phenol–DP adduct was cured with 4,4‐diamino diphenyl methane, phenol novolac, 4,4‐diamino diphenyl sulfone, and 4,4‐diamino diphenyl ether. The thermal properties of the cured epoxy resins were studied with differential scanning calorimetry, dynamic mechanical analysis, dielectric analysis, and thermogravimetric analysis. These data were compared with those for the bisphenol A epoxy system. The cured 2,6‐dimethyl phenol–DP epoxy exhibited a lower dielectric constant (ca. 3.1), a lower dissipation factor (ca. 0.065), a lower modulus, lower thermal stability (5% degradation temperature = 366–424 °C), and lower moisture absorption (1.21–2.18%) than the bisphenol A system but a higher glass‐transition temperature (ca. 173–222 °C) than that of bisphenol A system. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 4084–4097, 2002     

近红外光谱法在红曲菌固态发酵过程参数检测中的应用

研究了近红外光谱技术快速检测红曲菌固态发酵过程参数水分含量和pH值的可行性。针对传统基于间隔策略波长选择方法忽略非线性因素的缺点,采用一种基于最小二乘支持向量机(Least squares support vector machines,LS-SVM)非线性模型的波长筛选算法：联合区间最小二乘支持向量机(Synergy interval least squares support vector machines,siLS-SVM),并将新算法与相关系数法、iPLS算法、siPLS算法对比。实验结果显示,联合siLS-SVM算法和LS-SVM模型取得了最好的预测效果,水分含量、pH值的预测集相关系数(Rp)分别为0.962 1、0.976 1,预测均方根误差(RMSEP)分别为0.012 9、0.145 2,表明模型具有较好的拟合度和预测性能。应用近红外光谱法进行红曲菌固态发酵过程的水分含量和pH值的快速检测可行,该方法为进一步实现其过程参数的在线检测及发酵条件优化提供了技术基础。     

Phytochemical Analysis and Habitat Suitability Mapping of Glycyrrhiza glabra L. Collected in the Hatay Region of Turkey

The growth and quality of licorice depend on various environmental factors, including the local climate and soil properties; therefore, its cultivation is often unsuccessful. The current study investigated the key factors that affect the contents of bioactive compounds of Glycyrrhiza glabra L. root and estimated suitable growth zones from collection sites in the Hatay region of Turkey. The contents of three bioactive compounds (glycyrrhizic acid, glabridin, and liquiritin), soil factors (pH, soil bearing capacity, and moisture content), and geographical information (slope, aspect, curvature, elevation, and hillshade) were measured. Meteorological data (temperature and precipitation) were also obtained. An analysis of variance (ANOVA) and multivariate analysis of variance (MANOVA) were performed on the data. The soil bearing capacity, moisture content, slope, aspect, curvature, and elevation of the study area showed statistically significant effects on the glycyrrhizic acid and liquiritin contents. A habitat suitability zone map was generated using a GIS-based frequency ratio (FR) model with spatial correlations to the soil, topographical, and meteorological data. The final map categorized the study area into four zones: very high (15.14%), high (31.50%), moderate (40.25%), and low suitability (13.11%). High suitability zones are recommended for further investigation and future cultivation of G. glabra.     

Properties of High-Swelling Native Starch Treated by Heat–Moisture Treatment with Different Holding Times and Iterations

Tapioca and potato starches were used to investigate the effect of heat–moisture treatment (HMT; 95–96 °C, 0–60 min, 1–6 iterations) on gelatinization properties, swelling power (SP), solubility and pasting properties. Tapioca starch had similar content and degree of polymerization of amylose, but a higher amylopectin short/long chain ratio, to potato starch. After HMT, the gelatinization temperature range was narrowed for tapioca starch, but was widened for potato starch. Decreases in SP and solubility were less for tapioca than potato starches, coinciding with a progressive shift to the moderate-swelling pasting profile for tapioca but a drastic change to the restricted-swelling profile for potato. Moreover, decreasing extents of SP and maximum viscosity for HMT tapioca starch were, respectively, in the range of 47–63% and 0–36%, and those of HMT potato starch were 89–92% and 63–94%. These findings indicate that the granule expansion and viscosity change of starch during gelatinization can be tailored stepwise by altering the HMT holding time and iteration.     

Determining moisture absorption/desorption properties of commercial membranes by thermogravimetry (TG)

A series of different commercial membranes were characterized by their moisture absorption and desorption properties under controlled humidity and temperature conditions. This work was made possible by combining the features of a constant humidity conditioning chamber with those of a thermogravimetric (TG) apparatus. These two modules were interconnected by tubing, rotameters, an atmosphere-recycling microbellows pump and switching valves. Under programmed heating and isothermal conditions reproducible data were obtained in terms of weight-gain or weight-lossvs. time and pore size. Evaluation of the resulting TG curves allowed us to report reasonable differences in the materials, some of which had been previously surface-modified by the manufacturer.     

金催化CO氧化湿度增强效应的理论研究

实验发现纳米金催化的CO氧化有良好的湿度增强效应,但有关机制仍不清楚.我们应用密度泛函理论研究了湿度增强效应的微观机制,以Au4团簇为例,研究了金催化CO氧化的微观机理,考察了H2O在反应中的角色和作用.计算结果表明,H2O与Au4团簇一样,在反应中扮演催化剂的角色,参与反应的进行、改变反应历程、降低反应能垒.催化循环包含4个基元步骤：O2＋H2O→OOH＋OH,CO＋OOH→CO2＋OH,CO＋OH→COOH,和COOH＋OH→CO2＋H2O,其中自由基OOH和OH的形成是催化循环的速控步骤,其能垒为100.31kJ/mol,明显低于非水参与反应的能垒（161.41kJ/mol）.目前的结果合理地解释了实验观测的CO催化氧化的湿度增强效应,给出了其微观反应机制.     

壳聚糖季铵化衍生物的吸湿性与保湿性

壳聚糖季铵化衍生物的吸湿性与保湿性许晨，卢灿辉（福建师范大学高分子研究所福州３５０００７）关键词壳聚糖季铵盐，壳聚糖衍生物，吸湿性，保湿性壳聚糖是从虾、蟹等废弃甲壳中提取得到的一种生物活性物质［１，２］，由于其特有的直链聚阳离子结构，成膜附于角蛋白与...     

低分子量N-羧丁酰壳聚糖的合成及其吸湿保湿性

低分子量N-羧丁酰壳聚糖的合成及其吸湿保湿性;低分子量壳聚糖;低分子量N-羧丁酰壳聚糖;吸湿性;保湿性     

静水压下胶粘涂层的吸湿应力研究

根据半无限体的轴对称模型，对静水压下的胶粘涂层因填充粒子与胶层基体间吸湿性能的差别而引起的吸湿应力进行了研究，以达到饱和吸湿浓度的抗水力磨蚀胶粘涂层为例，对吸湿应力作了数值计算，并进行了结果分析