微通道板真空体电阻与Ⅱ代倒象微光管匹配关系的研究

国内研制的20/30Ⅱ代倒象微光管经常出现微通道板真空体电阻偏高或偏低的问题,直接影响Ⅱ代倒象微光管荧光屏的亮度和目标分辨力,严重影响微光管的质量。经过对20/30Ⅱ代倒象微光管的研制和理论分析,证明英国马拉德公司对用于××1383Ⅱ代倒象微光管的H36微通道板技术条件中真空体电阻技术指标的规定也存在一定的问题。本文从目前国内外工艺水平和有关文献资料的分析出发,进行专题研究。本文中所推导的计算公式和对文献资料提供的技术数据的推导分析,同样适用于其他型号微通道板的真空体电阻与相应Ⅱ代、Ⅲ代微光管匹配关系的计算与研究。     

应变Si1-xGex层中p型杂质电离常温和低温特性

本文采用解析的方法计算了应变Si1-xGex层中p型杂质电离度与Ge组分x、温度T以及掺杂浓度N的关系.发现常温时,在同一Ge组分下,随着掺杂浓度的升高,杂质的电离度的先变小,而后又迅速上升到1.在同一掺杂浓度下,轻掺杂时,杂质的电离度随Ge组分的增加先变大,而后几乎不变;重掺杂时,杂质电离能变为0后,杂质电离度为1.低温下,轻掺杂时,载流子低温冻析效应较为明显,杂质的电离度普遍较小,当掺杂浓度大于Mott转换点时,载流子冻析效应不再明显,电离率迅速上升到1.在同一Ge组分下,随着掺杂浓度的升高,杂质的电离度先变小,后变大,而后又迅速上升到1.在同一掺杂浓度下,轻掺杂时,杂质的电离度随Ge组分的增加变大;重掺杂时,杂质电离能变为0后,杂质电离度为1.     

现代热力学的完整分类系统--非平衡非耗散热力学新领域

在同一体系中同时有多个不可逆过程时，不可逆过程之间会有相互影响，原来的非自发过程有可能在其他自发过程的影响下得以进行，这种现象就称为热力学耦合或反应耦合，长期以来，经典热力学把热力学第二定律的等式作为平衡体系的充分必要条件，其中隐含了一个前提性的假定，即经典热力学的对象只限于非耦合的体系，摈弃这一隐含的前提性假定以后，热力学自身就发展成为一个现代热力学的完整学术体系，适用于任何宏观体系（包括极其复杂的生命体系），现代热力学的完整学术体系中包含了一个崭新的非平衡非耗散热力学新领域，由于该领域属于热力学第二定律的等式部分，因此可以定量计算，并得到一系列理论计算的非平衡相图，与文献上报道的激尖低压金刚石合成等的大量实验数据相符。     

Assessment of thermal expansion coefficient of methylsilsesquioxane thin film

For the methylsilsesquioxane film whose optical birefringence is almost zero, it was recently reported that its vertical thermal expansion coefficient (CTE) was approximately one order of magnitude larger than the lateral CTE. Though the birefringence is not an absolute predictor of anisotropic behavior, the discrepancy in both the CTEs was so remarkable that it was essential to investigate whether the anisotropy was intrinsic property or not. If the effect of Poisson's ratio is considered in the calculation of the vertical CTE and when elastic modulus measured by surface acoustic wave spectroscopy is used in the assessment of the lateral CTE, both the CTEs are coincident with each other. Therefore, it can be concluded that the discrepancy in the CTEs can be attributed to a higher in‐plane polymer chain orientation but it can also arise from the misleadingly assumed modulus and Poisson's ratio. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3109–3120, 2006     

Asymptotic analysis of elastic curved rods

We consider a sequence of curved rods which consist of isotropic material and which are clamped on the lower base or on both bases. We study the asymptotic behaviour of the stress tensor and displacement under the assumptions of linearized elasticity when the cross‐sectional diameter of the rods tends to zero and the body force is given in the particular form. The analysis covers the case of a non‐smooth limit line of centroids. We show how the body force and the choice of the approximating curved rods can affect the strong convergence and the limit form of the stress tensor for the curved rods clamped on both bases. Copyright © 2006 John Wiley & Sons, Ltd.     

A 24-GHz Patch Array with a Power Amplifier/Low-Noise Amplifier MMIC

This paper presents an active patch array designed at 24 GHz. It can be used as a front-end component for a phased array. A series resonant array structure is chosen which is compact and easy excite. With 5 elements, the array proved a 12-dB antenna gain. A power amplifier and a low noise amplifier are designed on a single GaAs chip (PALNA). Bias switch is used in the PALNA, which greatly reduces the switch loss in a transceiver and increases the efficiency. 20-dB small signal gain is achieved in both power amplifier and low noise amplifier. The active patch array is built by the combination of the patch array and PALNA. The measured active gain of this antenna is 35-dB for the PA mode and 31-dB for the LNA mode. This active patch array can obtain an EIRP of 34 dBm with a total radiated power of 22dBm and a maximum PAE of 32%. To check the noise performance, we applied sources at both normal temperature and 77K (liquid nitrogen) and extracted the noise figure (3.5 dB) of the active antenna by the Y factor method. The results proved that the active antenna is working efficiently as both a transmitting and receiving antenna.     

粘合衬对服装舒适性影响的研究

探讨了粘合衬与粘合工艺对服装透气性、透湿性及透水性影响的规律。得出服装的舒适性虽由面料决定,但辅料(粘合衬)的影响也不可忽视。粘合衬的涂胶种类,粘合衬本身的透气性与透湿性,以及非织造粘合衬底布的单位重量,机织粘合衬底布的覆盖系数等,均对服装舒适性有影响,从而为衬料的选择,以及粘合工艺参数的设定,提供了依据。     

铸膜液溶剂体系的物理参数与BCA不对称膜的透气性

铸膜液的溶剂体系（溶剂和非溶剂）对不对称膜形态的形成有重要作用。为了探索溶剂和透气性间的关系，本文考虑到了制备ＢＣＡ梯度密度不对称膜的各种溶剂的一系列物理参数，得到了一些定性结果，并指出了更全面、明确、解释两者关系的研究方向。