Luminescence investigations of the GaP-based dilute nitride Ga(NAsP) material system

Multi-quantum well heterostructures (MQWHs) of the novel Ga(NAsP)/GaP material system have been grown, pseudomorphically strained to GaP-substrate. The crystalline perfection is verified by transmission electron microscopy (TEM). For As-concentrations in excess of about 70%, a direct band structure and adequate luminescence efficiency for laser device application is observed. Temperature-dependent photoluminescence (PL) investigations show the influence of carrier localisation and non-radiative recombination processes typical for dilute nitride materials. With rising N content in the active material, the emission wavelength shifts towards longer wavelength, leading to Ga(NAs)/GaP MQW structures with photon energies below the indirect band gap of silicon (Si). At the same time the luminescence intensity drops due to an increase in non-radiative carrier traps and/or structural degradation.     

Fiber-optic reflex sensor for in-line production measurement

The paper describes experiments concerning distance measurement with fiber-optic sensor and improvement of the measurement principle. The sensor probe was well-designed with a small structure and multi-function. The novel optical fiber probe arrangement as well as the possibilities of use for complex measurement problems are explained using the measurement of an internal screw thread as an example. The experimental results show that the measurement uncertainty of the thread minor diameter can reach ±10 μm, and the stability of the measurement system is better than 0.07%.     

Laser induced copper electroless plating on polyimide with Q-switch Nd:YAG laser

The results of laser induced deposition of copper on polyimide substrate from copper electrolyte solution are reported. Unlike most work reported in the literatures where CW Ar⁺ lasers were used, a second harmonic (532 nm wavelength) Q-switch Nd:YAG laser was used for our experiments. The deposition process was conducted by laser-catalyzing of the polyimide surface and subsequent photothermal-accelerated reduction of copper-complex ions in an alkaline reducing environment. The characteristics of the deposited copper line were investigated in terms of laser beam scanning speed, and the number of scans. The surface morphology and chemical composition of the deposited copper were analyzed using field emission scanning electron microscope (FESEM) and energy dispersive spectrometer (EDX). The optimum processing conditions have been identified. The copper deposit was found to adhere well to the substrate.     

Polytetrafluoroethylene and metal structure convective-flow CO laser

A convective flow CO laser composed of polytetrafluoroethylene discharge tubes, nickel–chromium steel components, a cupric heat exchanger and other components is described. Operating in liquid nitrogen condition, output power of 60 W has been obtained from a non-selective cavity.     

New FIR laser lines and frequency measurements for optically pumped CD3OH

Twenty new cw FIR laser lines in CD₃OH, optically pumped by a CO₂ laser, are reported. The frequencies of 39 of the stronger laser lines were measured relative to stabilized CO₂ lasers with a fractional uncertainty, as determined by the reproducibility of the FIR frequency itself, of 2 parts in 10⁷.Contribution of the U.S. Government, not subject to copyright.     

用于机械振动实时监测的光纤光栅有源传感装置

把一对中心反射波长分别为1562.11nm和1562.71nm的光纤光栅粘贴在均质、等厚、等腰三角形悬臂梁上下表面作为环形腔光纤激光器端镜，当机械振动激励自由端时，通过观测激光输出脉冲，地施加于自由端的机械振动的频率进行了实时监测；观察两光栅波长漂移量差值的变化，可在0～6.1mm的范围内判断所测振动的振幅。低于100Hz时，实验结果与实际值基本吻合。     

应用型高技能数控人才实训模式的研究——以井冈山大学工学院为例

本文介绍了应用型高技能数控人才的培养目标,从加大设备投入、安装通用软件、保证学生实践时间、建立一支高水平师资队伍、加强校企合作这些方面着手,建立了一套较为完善的实训模式,以增强学生的编程、操作、软件应用等方面的能力。     

Fabrication and characterization of a PbTe quantum dots multilayer structure

Multilayer PbTe quantum dots (QDs) and SiO₂ were grown by pulsed laser deposition (PLD) and Plasma enhanced chemical vapor deposition (PECVD) techniques. The crystalline structure, QD size and size dispersion were observed by high-resolution transmission electron microscopy (HRTEM) measurements. This technique allows one to grow PbTe QDs as small as 1.8 nm diameter and 0.6 nm size dispersion. The whole structure can be used in a Fabry–Perot cavity for an optical device operating at the mid-infrared region.     

单光子态的产生与测量

报道了通过自发参量下转换产生单光子态的实验研究,使用中心波长425 nm的飞秒脉冲泵浦Ⅰ类非共线相位匹配的BBO晶体,在实验上得到单光子计数率为2.978×10-4,并分析了实验中的相关问题.